How Do I Connect Multiple Routes? How to connect multiple routers

Feasible is feasible.

First of all, you need to have a router as the main router, this router is used to dial numbers, assign IP addresses (DHCP), and send wireless signals or not up to you.

Secondly, the remaining 8 wireless routers have to turn off the DHCP function (very important!! Then manually assign addresses to these 8 TP-links, for example, your main router gateway is, then you can set the remaining 8 as, so that not only will there be no conflict, but also it will be much easier to manage these wireless APs, you can enter the IP address of each route in IE to enter the management.

In short, there are two points, one is to set up a main router, and the second is to turn off the DHCP of the 8 secondary wireless routes. If there's anything unclear, h, I'll do it.

Another point I forgot to mention that the line of the ADSL cat coming in from the telecom is plugged into the WAN port of the main router, and the line coming out of the 8 ports of the LAN port should be plugged into the LAN of the remaining 8 secondary wireless routes (note that it is not the WAN port!! Very important).

If DHCP is turned off, how can guests access the Internet?

In fact, it's very simple, set it as the main router, set it separately for other routers, don't be the same x, and then the upper LAN is connected to the lower WAN, it's as simple as that. However, it may have an impact on internet speed.

The connection of multiple routers is as follows:

1.Use the router used to connect to the Internet as the first router and this router as the primary router. If the router is newly bought, it has been restored to factory defaults.

2.Connect to your network via a network cable or wirelessly, and use a wired connection with Bucket Tsai Branch.

3.Open a web browser, enter the router login address in the address bar, and press Enter to confirm. Enter your username and password in the pop-up login box.

4.Set up this router to connect to an external network. Click on "Network Parameters" on the left and select "WAN Port Settings".

5.Select "PPPoe" in "WAN port connection type", enter the correct password, click "Save" at the bottom, save the relatives for about 10 minutes, and then click "Connect".

6.Second, the first router needs to start the DHCP service. Select the DHCP server on the left, and then select the DHCP service.

7.Just set the "DHCP Server" on the right to "Enabled".

8.Confirm or change the network segment of the background management IP of the router that is the same as the IP address in the DHCP sensitive address pool. Select "Network Parameters" on the left, and then select "LAN Port Settings".

9.Set the "IP Address" to the IP in the DHCP range you just set.

Specific steps:

First, the main (first) router configuration

Let's say that the router used to connect to the external network is the first router, and we use this router as the primary router. If your router is newly bought and more restored to factory defaults, then its IP should be. Connect to the network with a network cable or wirelessly, it is recommended to use a wired connection;

Open a web browser, enter the router login address in the address bar, and press enter to confirm. Enter the username admin and password admin in the pop-up login box, and set the router to connect to the Internet.

Click "Network Parameters" on the left, and then select "WAN Port Settings".

Select "PPPoe" in the "WAN port connection type", enter the correct password, click "Save" at the bottom, save it about 10 minutes, and then click "Connect", secondly, the first router needs to turn on the DHCP service. Select "DHCP Server" on the left, and then select "DHCP Service": Set the "DHCP Server" on the right to "Enable", and finally, in order to log in to the router in the future, it is necessary to confirm or change the same network segment as the IP address in the router background management IP and the IP address pool in the DHCP address pool.

Select Network Parameters on the left, and then select LAN Port Settings

Set the "IP address" to the IP address in the DHCP range you just set, for example, as shown in the figure above. Otherwise if separate from DHCP. If the address is different from the network segment, you need to manually change the IP address of the computer to static and set the gateway to the router IP when logging in to the router in the future.

Restart the router after the setup is complete. If the router does not reboot automatically, you can select "Reboot System" under "System Tools" on the left

Set the "IP address" to the IP address in the DHCP range you just set, for example, as shown in the figure above. Otherwise, if the IP address is different from DHCP, you need to manually change the IP address of the computer to static and set the gateway to the router IP address when logging in to the router in the future.

Restart the router after the setup is complete. If the router does not reboot automatically, you can select "Reboot System" under "System Tools" on the left

2. Configure the second router

All but the first router need to disable their DHCP function.

Similarly, connect the second router with a network cable and log in to the background management interface of the second router. If its IP is.

Open the browser, enter the background management IP", and then press the enter key

After entering the administrator account and password, click OK to open the background management interface.

On the left, select DHCP Server, and then select DHCP Service

Set the DHCP server on the right to "Do not enable".

Once you're done, restart your router.

Router bridging (WDS) is the connection of multiple routers to the first router through wired or wireless, and the Internet is accessed through the network of the first router. The main part of this experience is wired WDS. Here's how to set up multiple router connections that I've carefully organized, I hope it can help you.

The routing method of all devices is the same, but the difference may be that the configuration interface is different. Note: This document only describes the second router'Setup steps. The default login IP address is: Account: admin Password: admin.

The first connection method: the first router (LAN port) is connected to the second router (WAN port).

1) First, change the routing management IP of the second unit. (Restart is required after the change).

2) Configure the parameters of the second routing WAN interface.

3) Refer to the second router WAN port information.

Note that the following WAN interface information (because my first routing IP is the first one, and this IP is assigned from the first route) has obtained the first routing IP and can access the Internet normally.

The second connection method: the first router (LAN interface) is connected to the second router (WAN interface).

1) First, change the route management IP of the second unit. You need to restart the settings after the settings are complete.

2) Configure the WAN interface parameters of the second route (this method can be used in the case that the first route of the individual enterprise does not open the DHCP table, in this case, the second route can only be set to static IP).

The third connection method: the first router (LAN interface) is connected to the second router (LAN interface).

1) Disable the DHCP service of the second router (the DHCP server is actually the IP allocation function).

You need to restart the settings after the settings are complete.