How to adjust the display board of the 1438 fire floor?

If you want to adjust the process of the display board, you will have an idea of some of the distribution of the whole floor in the future.

If the main display board of the fire building adjusts the height of the floor, then the display on that floor can be adjusted upward.

1438 fire floor display gas version adjustment floor how to adjust this consulting architecture. Personnel.

This must be replaced with a new monitor, otherwise it will be adjusted from the high floor to the bottom floor, and its size will not match.

If you want to adjust the display of the fire protection system, then it must be adjusted according to the design drawings, if you do not adjust it according to the design drawings, it will be chaotic and inaccurate.

How to adjust the 1438 fire wave display foot board wall? Take a look at this, how do you send it?

1438's fire floor display board adjustment, floor, his debugging method can generally be adjusted through the background, this can also be cleaned up by one of his background data, and then re-**.

The fire floor display adjusts the floor, and then selects the floor settings.

1438 consumption can adjust the floor from the display palette how to adjust this drawing,You can adjust it to the middle,The middle is a problem of the middle layer。

If you go to work, the fire building, the display board is adjusted, and the floor is adjusted, I think you still have to be a property manager to help you get it, or it is more professional.

The adjustment process of the display panel on the fire floor can be adjusted.

According to the manual, adjust manually.

The number of buildings can be adjusted by the display version of the fire floor.

1438 fire floor display board adjustment, how to adjust the floor slab? This won't be.

How to adjust the total floor of the display version of the air conditioner in the 1438 fire building? This question requires someone with scientific knowledge to know how to adjust the floor. The people on the floor will only transfer me, and I won't.

1. The system wiring is not very reasonable, such as the line color is not uniform.

1. The line is not firm, there is no record of the school line, the terminal row is not standard, the wiring is wrong, and the protection of the inner pipe of the concealed project is not in place; The fire protection line and the alarm linkage line are worn in the same line pipe, and the weak and strong current lines are laid in the same bridge or trunking.

2. The insulation resistance of some projects cannot reach 20m, and some are only, which affects the reliability of system operation. The working grounding and protective grounding are not done well, and there is no grounding resistance inspection record. The power connection of the alarm controller is plug connection.

The wires in the alarm control cabinet are not numbered, not tied, etc.

It's the same, the fire graphic display says it's CRT's.

The fire CRT system is a kind of graphic display system, and the graphic display system has a wider range.

The hardware of the fire CRT system is universal, and there are many LCD displays at present. The operating software is provided by the manufacturer of automatic fire alarm equipment, and encryption measures are generally taken.

1. CRT hardware (host and display) configuration standard: the computer host is a commercial machine or above (industrial computer), and the liquid display is 19" (16; 9), CPU is dual-core, memory 2G, hard disk 160G, independent graphics card, 1 RS-232 serial port, active speaker 3W, genuine WindowsXP, graphics card resolution 1440*900.

2. CRT graphic software (according to the circuit or fire partition configuration) fire control room graphic display device can be used for the management and control of fire alarm and fire linkage equipment and the graphical display of equipment, and can be produced by Bay Safety Technology GST200, GST500 5000, GST9000 and other series of fire alarm controllers (linkage type) to form a fully functional graphical fire center monitoring system. And GST-GM9000 graphics display devices can be networked through LAN, RS-232 RS-422 and other ways to receive, send, display the abnormal information of the equipment and host information, so as to realize the remote monitoring of the fire alarm system.

There are two main parts:

1. CRT hardware (host and display).

Configuration standard: The computer host is a commercial machine or above (industrial computer), liquid display 19" (16; 9), the CPU is.

Dual-core, 2G RAM, 160G hard drive, independent graphics card, an RS-232 serial port, and active speakers.

3W, genuine WindowsXP, graphics card resolution 1440*900 II, CRT graphics software (configured according to circuit or fire partition).

CRT host (computer) + fire alarm controller.

It is not a graphical display device software.

If the display is not broken, there is a problem with the display software, reinstall the software.

If it's a hardware problem: it may be that there is a problem with the controller's communication board or that the communication port between the computer and the controller is broken.

The original meaning of the floor display is to display the alarm system of the floor, one for each floor. However, in residential buildings, there are only smoke detectors, hand alarms, sound and light devices on each floor, so there is no need to install one on each floor, and a floor display can be installed on the first floor to display the alarm equipment of the unit.

The fire protection is called "fire display panel".It is a fire alarm display device that can be installed on a floor or in an independent fire protection area.

It is used as a fire alarm device on the floor or in a separate fire protection area. When the host controller of the control center generates an alarm, and at the same time transmits the alarm signal to the fire display panel in the fire area, the display disk will display the detector number and related information of the alarm and send out an alarm sound.

In practice, some high-end buildings are installed on every floor, but most of them are only equipped with fire display panels on the first floor. In addition, older properties do not have this thing.

Unreasonable, the floor display is used to display the alarm equipment on each floor, can not only be set on the first floor, and other floors do not, should determine his protection range.

GB50116-2008 automatic fire alarm system design code.

4.When a fire alarm controller is used to guard multiple floors, a light display device should be set up to identify the fire floor at the staircase or in the front room of the fire elevator on each floor.

Not necessarily, it mainly depends on the design.

Code for Design of Automatic Fire Alarm System GB 50116-2013 No. 6, 4, 1

Each alarm area should be set up with a regional display (fire display panel); Hotels, restaurants and other places should set up a regional display in each alarm area. When an alarm area includes multiple floors, it is advisable to set up a regional display on each floor that only shows the floor.

Depending on which manufacturer produces it, there are generally two kinds: 1Communication line + power cable. 2.Signal line + power cable. Now the second type is more commonly used.

How to wire the floor display? Today, let's first take a look at the floor display, which is what we often call the fire display panel, also known as the layer display, which can generally be installed on the floor or in the independent fire prevention area of the fire alarm display device, which can be divided into three types: digital, Chinese and English, and diagram. Placed in each floor or zone to display the fire situation in that floor or zone.

When the detector and other devices in the area are alarmed, the display disk sends out an audible and visual alarm signal and indicates the alarm area and part code and annotation information. The fire display panel can only display fire alarm information, and cannot display other information such as faults and actions. The display area of the fire display panel can be set by the fire alarm controller, and the fire display panel of the setting buckle can only display the fire alarm information of the area.

How to wire the floor display? Depending on the brand of the fire display panel, the wiring method is also different. At present, there are two types of wiring of the common fire display panel: loop type and RS-485 communication bus type.

Each RS-485 bus can be equipped with up to 64 fire display panels, and a separate set of RS-485 communication buses needs to be placed from the fire alarm controller to the fire display panel. The fire display panel of the signal bus type can be adapted to the equipment location of each circuit.

How to wire the fire display panel? The previous display disc of making a tooling was lost by the worker, and now I want to buy a new one, does this have to distinguish the model? Or buy any one and there are 4 lines in the back, which was taken on other floors!

No, the monitors on this floor are suitable for the circuit connection of this floor, and they cannot be cross-regional and co-line.