After a while of booting, I listened to a beep, and the mouse was not good, and it was okay after re

Desktop or laptop? Try it when the desktop is plugged in close to the network cable port, it should be the mouse drive off Although it is plug and play, if the system is a little flawed, there may be problems with the mouse No, redo the system to see.

The computer keeps beeping and the mouse won't move, probably due to one of the following reasons:

1.The system has entered a dead state: At this time, you can try to force shut down the computer and restart the system.

2.Insufficient computer memory: When the computer memory is insufficient, it will cause the system to respond slowly and slowly. At this time, you can close some running programs or upgrade to expand the memory.

3.If there is a problem with the mouse driver: Check whether the mouse connection is normal, and try to replace another mouse to determine whether it is the problem of the mouse itself.

4.Virus infection: If your computer does not have anti-virus software installed or the anti-virus software does not update the virus database in a timely manner, it may cause problems with the virus on your computer.

At this point, you need to install and update antivirus software and conduct a comprehensive virus scan. If the above methods do not solve the problem, it is recommended that you contact a professional maintenance personnel for inspection and repair to avoid further damage to your equipment.

Your method is correct, and there are similar problems when trying it on multiple computers, apparently caused by the poor quality of the mouse purchased online.

What are you saying about being bad?

If it's running some programs and the mouse is abnormal or something, go to the next mouse driver, if it's a failure caused by the hardware of the mouse, change the mouse, and you can't fix the optical mouse yourself.

System Restore is broken, you can restore it.

Reasons and solutions for computer not turning on:

Step 1: If there is no power response, then check whether there is a power supply, poor contact, hardware and other problems, go to the second step, if you can't enter the system, it may be an operating system or software problem to go to the third step.

Step 2: Check whether there is a power supply problem, first see if the power supply is not plugged in well or there is a problem with the plug, if you are using a battery, then plug it in and try again. You can go to a friend or go to a computer repair shop or sales store to find the same model of power supply to try it.

After replugging the power supply, press the power button again, and if it still can't be turned on, then press it for a while. If you change someone else's power supply to turn on, it means that there is a problem with the power supply, if it proves that there is no problem with the power supply, it may be the hardware reason, go to the fifth step.

Step 3: Go to the last correct configuration to adjust, turn on and press and hold F8, enter the advanced options page, select "The most recent correct configuration", and press Enter. If it can enter the system, it may be caused by viruses, incompatible hardware drivers with the system, or operating systems.

After entering the system, run the anti-virus software, check and kill the virus, if there is a virus, restart the computer after the anti-virus, if it is not normal, it may be caused by the incompatibility of the device driver and the program, delete the graphics card, network card and other drivers, restart it after removing the driver, if there is still a problem, then go to the next step.

Step 4: Repair and install or reinstall the system, set "Optical Drive as the first boot device" in the BIOS, then insert the system disk, and press the R button to perform "Repair and Installation". If the fault persists, just at the beginning of the system, select "One-click GOST to restore the system" or use the system disk to reinstall the system.

Step 5: Check whether there is a hardware problem, disassemble the notebook to see if the hardware is loose, generally the hardware is not plugged in well, there will be an alarm sound, the long sound continues to sound that the memory module is not plugged in tightly, one long and one short means that the memory or motherboard has a problem, one long and two short means that the graphics card is wrong. If there is too much dust inside the notebook, it is best to clean it up first.

In addition, pay attention to whether it is caused by the new hardware, if it is normal before the replacement of the hardware, and it is not normal after the replacement, then check whether it is compatible. If it can't be started at this time, it is best to send it for repair, and the professional will check whether there is a problem with the hardware one by one.