265sp printer problems, printer printing problems

The printer does not print for many reasons, which can be divided into the following situations:

1) The printer is set to "Pause Printing". Open the printer's window, right-click the program icon of the printer installed on the current system, and remove the "pause state". (Misawa Pioneer.)

2) The printer is not set as the default printer.

3) The printer is not online. Check to see if the "online" light on the printer's control panel is on.

4) The printer port used by the current program is inconsistent with the set port.

Start -- Settings -- Control Panel -- Printer -- Properties -- Details -- Print to the following ports, check whether the port of the printer is the same as the port set.

5) The computer configuration is low, which causes the printer to output too much content and cannot be printed? (Just start your computer from scratch).

6) The printer has been set to timeout. You can take a look at the settings again.

(Misawa Pioneer.) Please indicate the source for the citation.

You also said that I just bought it, and I took it to the Canon repair department to help you solve it for free.

What about the situation you mentioned, I think the most likely problems are: I want to first see if your driver is installed correctly, and then see if the port or data cable is good, if it is a problem with the machine, it may be a problem with the control panel or the main version. After a simple inspection, if it doesn't work, it will be sent for repair.

If you are a warranty machine, it is best not to dismantle it yourself, otherwise people say that some things are broken by you, if you are an out-of-warranty machine and you are also interested in this aspect, you can also disassemble it yourself.

In fact, there are a lot of problems that printers are prone to, so you should be familiar with some basic knowledge and operations of it. That's it. 88

I've already told you about the number one upstairs! That's the answer!

It is possible that the print interface is broken.

The first floor is basically finished!

First, put a few sheets of paper in the feeder first.

2. Enter the maintenance mode (that is, press and hold the recovery button with one hand; Press the power button with the other hand to turn on, press the recovery button twice at the same time without releasing the power button, and then release the hand that presses the power button, and wait for the printer to complete the action, the green light is not flashing, and it will enter the maintenance mode).

3. Press the recovery button four times, press the power button again, then the power light will flash once, and then press the power button again, so that the machine will print a piece of paper with the word d=. So far, the clearance has been successful. It's good to start from scratch.

Note that some machines may have to clean the nozzle before printing, so don't worry, wait slowly until the word 0 is printed).

Note: I see other posts that have random attempts, don't do it easily, I don't say this to slander others and elevate themselves, but the result of random press will produce other inexplicable failures, after all, a good machine should take good care of it, it will be obedient and do its job!

BC-03 ink cartridge, BC-06 color cartridge The original ink cartridge is more expensive, about 300 yuan, you can also try to use alternative ink, ** it will be cheaper, go to your local electronic city to find it, there should be a suitable ink.

No need to have no ink cartridges, adding ink to it is the cheapest, Canon's biggest disadvantage is that the ink cartridge is expensive, I never buy a new one, just add water to it, it's very cheap, you have to do it yourself, the merchant won't tell you, it's troublesome to say, you will succeed if you do it yourself!

Possible causes:

1.The drum inside the cartridge may have been scratched or worn.

2.Printer (general guide paper channel) is read next to toner stained sail land dyeing. When there is molten toner on the paper guide in the paper guide of the printer, and the printing paper is rubbed onto the printing paper when it passes, a black line will be formed.

3.Other hardware issues within the printer.

Methods of diagnosing high state of mind:

Print the offline self-test page on the printer or send a print command on the computer, turn off the printer when the paper enters the printer two-thirds of the way (do not let it enter the heating element), the printing will stop, open the front cover of the printer, take out the toner cartridge, take out the paper and observe (the handwriting on the paper should be erased) to see if the printed half of the paper still has a black line, if there is still this phenomenon on the paper, it may be a failure of the laser-related parts or a problem with the toner cartridge, It is possible to replace the test with a new toner cartridge. If there is no such phenomenon on the paper, it may be that the heating element of the printer is faulty, and it is recommended to contact the local service center to test the printer.

The problem is in the ink cartridge, I don't know if you install it in place, reinstall it, but use the printer's built-in cleaning side to see if the water can come out, if it is the same, you can only replace the ink cartridge with a new one.

There is no problem with the printer, the storage of the cartridge is time-limited, and if it doesn't work, buy a new one.

I suggest you buy a printer directly, because the current inkjet printer is not worth much, like your 265SP is now second-hand** around 130-150 (the new one can't be bought, and it is discontinued).

Not compatible, this is also the case with one of my printers, which can be installed hard. It's just that there will be some problems when printing. I ended up buying a new printer.

According to the action before the failure, whether the new ink cartridge replaced is the first merchant or self-filled ink, ink residue may cause the inkjet to be unsmooth and cause the problem described. Suggested Solution:

1. Use the "printhead cleaning" function of the printer driver to freshen up the printhead;

2. Delete the printer and use the driver again.

The green light is generally data, etc., flashing indicates that there is data transmission.

How many years have you been using?

Estimate the problem

1: There is a problem with the sprinkler

Phenomenon: No ink, printing nothing is useless.

It is recommended to clean the nozzle, only to change it to a new one, and the green light keeps flashing

Because the print task is not completed (the paper cannot be fed or the printing is interrupted due to a failure), it will keep flashing.

It is recommended to turn off the computer and printer again, turn on the computer and printer again, do not move the paper, there is a problem with the suction part, or the paper feed is stuck, if there is a problem with the sensor and the paper is not fed, then you have to change it again

First see if the sensor is broken, and then whether the sprinkler is blocked!

BJC's machine has long been eliminated, the speed is slow, if you want, you can go to the **, or go to the good energy consumption material store, it is recommended that you change to Canon's new machine, now Canon inkjet printer** is about 230 500, inkjet all-in-one machine is only more than 500, it is not worth your investment in BJC.

Go to **, pat pat , there is ah to buy above, but it is recommended that you buy a new machine, you have the money to buy a cartridge almost to buy a new machine, and the current machine performance is much better than your BJC effect.

The printers are almost antique, and the ink cartridges are not easy to buy, so it is recommended to replace them with new ones as soon as possible.

Let's change to a new machine I heard that Canon has recently launched three more models Xuanfei CP770, Canon ES3, Canon ES30, and they are all dye-sublimation printingVery good