TD W89841 Router How to Set Broadband Rate Limit to 50

How to set a router broadband speed limit.

Before setting the router broadband speed limit, we must first understand how much bandwidth we have opened, and how many computers share these bandwidths together, here we first take our broadband is 2M, 2 people are using it at the same time, and the IP address is automatically obtained as an example to set the bandwidth rate limit of the router.

1. Set up automatic IP address acquisition.

DHCP Server: Enabled.

Right-click on the network neighbor - Properties - Local connection - Properties - double-click the cp IP protocol - > to get the IP address automatically.

2. Restrict broadband settings.

1. Set up IP broadband control.

Before enabling IP broadband control, select the following broadband line: ADSL line, total uplink bandwidth: 1024, and total downlink bandwidth

2. Set the IP broadband control rule list.

I'm here to limit the bandwidth of 2 computers, so you have to set 2 rules when you set up, if you have set broadband speed limit in front of your router, you must first delete all the original settings (click to delete all entries). As shown in Fig

Downlink: Maximum 1024 (this place is the value of limiting bandwidth, 1024 is the average score of 2048 2, you can also set a slightly larger 1200), and finally click "Save" after setting all the parameters.

Then add the second tone rule, add a new entry - > IP bandwidth control rule configuration.

The above are the steps for the router broadband speed limiting.

Change that value and click Save. OK.

Here's how to throttle someone else's internet speed:

1. Log in to the management page of the router first, find your MAC address, and bind them one by one, so that these computers can only access the router with the IP address that follows in the future;

Run --cmd--ipconfig all on your computer to get the local mac) in advance

2. After the MAC address and IP address are bound, enter the bandwidth control module and limit the rate except for your own IP address.

With the same router, it is inevitable that someone will watch a movie to occupy the network speed, and many people will think about how the router can limit the network speed of others, and the method is as follows:

1. Log in to your router settings first**, enter it in the browser and the login window will appear, enter the login password to log in!

2. First of all, we can take a look at the IP addresses on our router, and click on the IP and MAC binding-arp mapping table in the left navigation!

3. Then we can see the IP address segment on the router, most of which are started!! Take a look at the IP address and set it up when it's time to set it up!

4. Then click on the IP broadband control in the left navigation. Then click on Control Rules!

5. Click the button to add a new entry in the settings!

6. Then the most important thing is that this rule is set, your own IP can avoid this rule, for example, you can set the address range to - and then set your own IP to , you can basically control the network speed of others in all routers! If you set the port segment to 20-65535, you can do that. Then it's time to control the internet speed.

Here according to the size of your network cable control is good, there is no need to set it too rigidly. It's okay to be average!

7. Click OK after setting! Then reboot your router! You can restart the router directly in the system settings in the navigation of the router settings page!

1。Open the webpage into the router, tp is, if the default username and password are not set admin, there is a label behind this router.

2。After entering, select IP broadband control, and check to turn on IP broadband control. Then enter his IP address, if the person computer is not set to automatically obtain the default IP starting pool of the router starts from the minimum, such as the general starting pool, then you set it to, and select the back to limit the maximum bandwidth.

Then change your own IP to so that you are not restricted. For details, see **The section circled in red.

Enter the router, select i bandwidth control, select the control rule, and then add a new entry, fill in the IP segment of that computer's IP, fill in one, fill in the port segment 1-65534, fill in the minimum 1 in the uplink, fill in the maximum 1024, the same in the downlink, and save it.

Here's how to set it up:

1. Open the browser, enter the router management IP address, press enter, the address is default;

2. Enter the administrator account and password in the pop-up window, click OK, and the default is admin;

3. After opening the settings page, click QoS--QoS settings, click on the right to enable QoS, enter the broadband downlink rate and uplink rate, note that the unit is kbps, and click Save;

4. Click QoS rules and click Add New Entry.

5. Enter the start IP and end IP of the address segment, if the same means that a single machine is restricted, it is recommended to choose an independent bandwidth mode, and the following are set to ensure the minimum downlink and uplink bandwidth of each host, as well as the maximum downlink and uplink bandwidth allowed to be occupied, other options are as shown in the figure below, click Save after setting;

6. Multiple rules can be added repeatedly, and they will take effect immediately after setting.

If the router function can be set with speed limiting, if it is not set with speed limiting, the speed limit function can be limited in the following ways to limit the network speed The premise of speed limiting is to know the IP address of the computer you are restricting, you can enter cmd into the DOS program at the beginning of the run, and then enter ipconfig to view your own IP address, if you don't know other people's IP can be within the IP limit without entering your own IP The landlord first enters the router settings, Enter the account password of the router in the address bar of the browser, which is generally the default admin admin (the password can be modified), and then there will be a series of menus on the left as shown in the figure.

The landlord is welcome to adopt.

How to set wifi bandwidth control on a wireless router:

1.The system is connected to a WiFi network.

2.Open a computer browser and enter the gateway IP address of the nameplate on the back of the router (generally, enter the gateway configuration interface.

3.Go to the DHCP client interface and use static assignment to bind the device with the assigned IP address to an IP address that is specifically used for rate limiting.

4.Enter the bandwidth control setting interface in the router advanced, enter the range of the IP address corresponding to the device that needs to limit the network speed, set the bandwidth limit, and click Enable.

There is a problem with your question itself, let's see if it's this.

Hello, method steps.

There are more users who access the router, and it is inevitable that they will encounter frequent movies, which occupies a lot of bandwidth, and limiting his bandwidth will not have any impact on his watching movies, and the router has this speed limiting function. Open a browser on a computer connected to the router, enter the IP: Enter, some router addresses IP:, a login box will pop up.

Enter administrator in the login box, the default is admin, the initial password is admin, it is best to change the initial password, log in to the router management background, different management interfaces of routers may be different, and the functions are similar.

In the left-side navigation bar, click IP Bandwidth Control to go to the bandwidth operation page.

The set bandwidth information is displayed on the page, and below the rate limit list, click the "Add New Entry" button.

In the new entry settings, enter the range of the IP address, if it is just a separate IP, just fill in the starting address, and then set the uplink broadband and downlink bandwidth, that is, the upload speed and ** speed, and click the save button.

Return to the IP bandwidth control page to see the IP record of the new limit you just set, and then put a checkmark before enabling IP bandwidth control, save and exit the router management background, and the rate limit will take effect.

It's also easy to delete the speed limit setting, just delete the entry of the setting.

Change a batch of relevant experience.

How to set the speed limit of the TP-Link router?

How to set the speed limit on the router.

How to set the speed limit on the router.

Router speed limit settings**.

How to set the router speed limit.