Tengda TEI402 router setup problem

Updated on technology 2024-02-09
9 answers
  1. Anonymous users2024-02-05

    What you said 4M is bandwidth, if so, you should first set a static IP, and then look at your local IP address, Tengda's routing IP should be, and then check the limit bandwidth in the bandwidth settings, if your IP is, set to, upload limit is 25K, **Set to 200K, so that you are not restricted, and the other two machines share 2M bandwidth.

    Don't forget to restart your router after the final setup so that the setup takes effect.

  2. Anonymous users2024-02-04

    2. Log in to the router interface, click "Advanced Settings" - "Bandwidth Control" to select Enable.

    3. Set the bandwidth of computer A to 1m, and the bandwidth of computer B to 1m.

    Upload speed range: 15 30kbytes

    Enable Add to List.

    Enable Add to List.

    Upload speed range: 15 30kbytes

    Enable Add to List.

  3. Anonymous users2024-02-03

    No, 1m is enough for one person.

  4. Anonymous users2024-02-02

    Hello! For details, please refer to the following sections:

  5. Anonymous users2024-02-01

    1. Enter the router:

    Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name, password, (the default is generally admin).

    2. Wireless Settings - Wireless Security Settings - Select [WPA-PSK WPA2-PSK].

    Authentication Type: Automatic.

    Encryption algorithm: AES.

    The PSK password is the wireless password. Set the required password.

  6. Anonymous users2024-01-31

    Tengda TEI402 is not a wireless router, it is a wired router and has no wifi function.

  7. Anonymous users2024-01-30

    That's right. It's better to be automatically assigned. As I said, you only have three computers, and 4M bandwidth is enough.

  8. Anonymous users2024-01-29

    The quality of Tengda's routers is average. On this kind of ordinary router, QoS has no practical meaning.

    If it is easy to drop, there may be one of the following reasons:

    1。If you are on a local area network and your computer has a virus, the virus will continue to attack the network automatically, causing the router to be unable to process the data and the network will be congested. causing network paralysis;

    2.The quality of the router is not good, so try to buy the best router, not in order to save a little money (now the price difference between large brands and small brands of home routers is very small, generally no more than 20).

    3.Turning on routers, cats and other devices for a long time causes these devices to heat up and crash, and cannot process network data correctly.

    Routers, cats and other network equipment, especially small household types (don't ask me why, Internet cafes can wait, these network equipment is professional, high, powerful, with special processing solutions and technologies, etc.) In fact, it does not support continuous use for a long time. Sometimes you may feel that you have never turned it off, and he can use it, and I am not saying that it can't, but try to avoid turning it on for a long time.

    If used for a long time, it will cause the router, cat and other devices to heat up, unable or unable to process network data in time, which may be manifested as slow network speed, or dropped connections, etc. Therefore, it is recommended that when you turn off your computer, you should also turn off these devices and turn off the power. This not only saves power and network resources, but also makes a reserve for better performance next time you use the hardware.

    If it's not convenient to turn off these devices, you should also turn them off for at least 30 minutes during idle use before continuing to use them. At the same time, these devices should be kept in a ventilated area, just like a computer.

  9. Anonymous users2024-01-28

    Cheap, not easy to use, it took half a day to connect, sweat.

Related questions
14 answers2024-02-09

Yes, the router can only be used as a hub, don't use the WAN port, just plug it into other ports. Also, the router cannot be configured with DHCP, otherwise it may cause IP address conflicts. In other words, the router doesn't need to be equipped with anything, just use it as a hub.

7 answers2024-02-09

From the LAN port of the main router, a network cable comes out and connects to the LAN port of the wireless router, log in to the wireless router, turn off the DHCP service of the wireless router, and set the IP address of the LAN of the wireless router, which should be different from the LAN IP of the main router.

15 answers2024-02-09

1. The broadband network cable or the network cable out of the cat is connected to the WAN port of the router, and the LAN port is connected to the computer. >>>More

10 answers2024-02-09

As the main router that uses the account virtual dial-up to access the Internet, WDS cannot be enabled, and the secondary router enables WDS to tick, and the bridge password method and password must be the same as the wireless security password method! That is to say, during the bridging process, the router needs to enter the password in 3 places, namely: 1, the wireless security settings of the main router, 2, the bridge security settings of the secondary router, and the wireless security settings of the 3rd secondary router. >>>More

28 answers2024-02-09

The first thing that can tell you is that there are no problems with your network and routing. The situation you mentioned is that the firewall trusts the software or accesses ** and automatically prohibits access because it does not trust the plug-in; The second is because you are connected to multiple computers and other computers are opening BT and other software** things or the network itself, resulting in the network speed is too slow (because of the advantage of bandwidth and response speed, it will be faster than others**, QQ because the data exchange with the host is different from IE, so it is not easy to find), if this is the case, you can enter the ping command in the command box to ping the local telecom host to judge, the more the value in the ms column in the beating data** the faster the clear network speed, The command format is ping the telecom host IP (for example, -l 1024 -t for Jiangxi; The third is that the data flow of the ** you are accessing itself is abnormal, resulting in a short-term failure or slow access.