How to plug the water nozzle The water nozzle leaks in the wall

It can be heated and blown indoors, so that the inside of the wall can be dried quickly.

021-22816736 The construction steps are divided into the following steps: 1. Chisel the leaking part next to the sewer pipe with tools such as hammers and chisels, and chisel into a ring shape along the entire sewer pipe. Its depth and width depend on the situation.

2. Use waterproof coating and high-efficiency waterproof powder to synthesize a waterproof sealing paste with high concentration and high hardness to seal the annular groove. 3. Strengthen the maintenance of waterproof materials, after two or three curings, the performance of sealing materials will reach the best state. The main cause of the leakage of the exterior wall waterproof exterior wall is the improper construction of the facing brick, the facing brick itself is impermeable because it is a sintered ceramic, and the adhesive material is cement slurry, which is easy to cause the four-sided mortar of the facing brick to be not full and form a cavity.

The exterior wall is waterproof and due to the cement joints between the tiles and the tiles appear very fine transverse cracks and some honeycomb, hemp surface and dog holes, rainwater is easy to penetrate into the screed layer and tile lining from these joints, holes and holes, and is adsorbed in them, because the facing bricks are impermeable, the water is trapped in it and forms a small reservoir, which can only seep into the room. After the rain, when the sun shines directly on the exterior wall, due to the high temperature outside and the low temperature inside, it is stored in the screed layer at this time, and the water vapor of the tile lining enters the inner wall through the capillary pores of the screed, resulting in dampness of the inner wall and moldy interior decoration, and white minerals flow out of the outer wall from the inside, which affects the appearance of the wall. The governance approach is broken down into the following steps:

1. To do exterior wall waterproofing, the exterior wall must be cleaned first, so that the surface is free of oil stains, and there are no loose particles such as dust and cement and all sundries left in the holes and cracks. 2. The exterior wall waterproofing is mixed with waterproof powder and JS composite waterproof coating according to the ratio of :1 to make a repair paste, and all the cracks on the ash joints between the bricks are filled with dense holes.

3. After it is dry, spray the exterior wall with silicone water-repellent agent. Silicone water repellent agent is an environmentally friendly product, which does not change the color of the original substrate, is not easy to stick to dust, and does not affect the decorative effect of facing bricks. The exterior wall waterproofing is closed by a large number of capillary pores and microscopic cracks by the water-repellent agent, and the water-repellent coating layer formed by the water-repellent agent on the exterior wall makes it difficult for the rainwater to stay on the exterior wall like falling on the lotus leaf, which eliminates the leakage of water, so as to achieve the purpose of waterproofing.

Changsha Jiacheng Waterproof Engineering Co., Ltd. is an exterior wall waterproofing company with more than 20 years of experience in waterproof engineering construction, and undertakes all kinds of new and old roof waterproofing, exterior wall waterproofing, bathroom waterproofing, roof garden waterproofing, basement waterproofing, exterior wall waterproofing, pools, dams, tunnels waterproofing and leakage plugging engineering, anti-corrosion and thermal insulation engineering, ground moisture-proof and concrete beams, columns, slabs, honeycombs, cracks of chemical grouting reinforcement engineering, contracting the design and construction of the overall waterproofing project of new and old buildings.

We all know that for the sake of aesthetics, the water pipes in many people's homes are in the wall, but due to various reasons, the water pipes in the wall in many people's homes are leaking, which makes many people very anxiousWhat to do if the wall water pipe is leaking?If you don't know, come and find out!

What to do if the wall water pipe is leaking: Determine if the water pipe is leaking or not. Follow the line of the water pipe with an iron rod.

One end is placed on a wall or the ground and the other end is attached to the ear. Listen carefully, and in general you can find the localized area of the leak. Overflowing toilets and water tanks can cause miscalculations.

The water slipped away. You didn't find it. Usually, there is a water level column inside the tank.

What to do if the wall water pipe is leaking: First cut off the water source, then remove the male and female nuts and female nuts connected to the compression joint, wrap several layers of threaded sealing tape around the thread, and then connect the joint from the head. Once a casing joint leaks, it may be necessary to remove the fitting and reinstall many water pipes, so the maintenance personnel should be notified promptly for repair.

No matter what type of water pipe joint is leaking, we can use special tape for temporary repair.

What to do if the wall water pipe is leaking: We need to close the valve so that we can cut off the water source, turn the faucet to a less obtrusive position, drain most of the pressure from our pipes, and then tie the leaking part with special tape, or seal it with a layer of tree grease adhesive.

What to do if there is a leak on the wall at home, when you are left at home, you can do it step by step according to the above introduction, so that it can be repaired temporarily. If there is a water leak, it will make the wall damp, and the wall skin will fall off over time, which will have a huge impact on our lives. Therefore, we must know the method of repair and preventive measures.

You can get it for free

<> "What to do if the water pipe leaks inside the wall.

First of all, we must find the leakage point, close the main gate of the water inlet, and then pry open the tile and cement layer on the ground, if it is a PVC water pipe, first cut off the broken pipe, prepare a joint of the appropriate size, and connect the joint with the water pipe immediately after hot melt through the hot melter, if it is a cast iron water pipe, then it is necessary to weld the buried liquid, and if it is serious, you can replace the new water pipe.

What to pay attention to when installing water pipes

1. The installation should be carefully in place, do not change it at will, so as not to cause problems in the future, it is best to do a "water pressure" test after installing the waterway, if there is a problem, you can deal with the kitchen and bathroom walls and floors in time to repair and do waterproof construction.

2. Water pipes, joints, faucets, etc. National standard high-quality products must be adopted. The installation and transformation of the circuit must be standardized, and there must be professional human factor construction.

The construction must be carried out in accordance with the specifications and requirements, or save some materials and check for irregular wiring or the use of defective electrical products.

3. If you use the hole left by the expansion screw. It can be filled with cement, and then it is better to wait for the holes to dry. If there is water, it may affect the bonding effect.

Find a screw that can be used to pass through the fixing hole of the water pipe, because the surface of the screw is rough, so it is easier to connect the liquid water. Thread the screw through the fixing hole in the water pipe and into the hole in the wall.

If the water pipe is leaking, use waterproof tape foam glue and glass glue to seal the water pipe. There will always be a source of water leakage to find the leakage place, generally the water pipe is embedded in the wall, when the water pipe leaks, the wall is wet, but you can still see where the leakage is. The water is from the top down, so if you look all the way down the wet marks on the wall, you can still find the leaky pipe.

Mark leaking water pipes. If the water pipe is indeed inside the wall, then it is necessary to hire workers to drill holes and open the wall. If the water pipe leak is outside the wall, it will be easy to do. See what material the water pipes are made of. Such as plastic, steel, PV and so on.

Waterproof band. You can go to the hardware store and buy this, it's very cheap. Wrap a few layers of waterproof tape (also known as waterproof paper) on the outside of the leaking water pipe, then wrap another layer on the outside with foam glue, then wrap it with waterproof paper on the outside of the foam glue, and then wrap it with foam glue on the outside of the waterproof paper, and finally put on glass glue.

You can find the repair man, if the leak is small, you can use the energy in the repair man to paste it to the leak point, and you can wrap it with the universal repair belt!