How to set the routing function of Huawei HG232 has been learned,

You have to know its super password, and that's the first step.

The specific Huawei HG8342M wireless router is set up as follows:

1.Connect the power supply of the router, and then plug one end of a network cable into the network port of the computer, and the other end into the LAN port of the router.

2.Open the browser of the computer, enter the IP of the router in the address bar, click the enter key to enter the router settings page, the user name is admin, the password is blank, click to log in, and enter the router settings home page.

3.Once you're logged in to the home page, select Manual settings. Then select Manual Internet Settings, and Home Dial-up users select the PPPoE connection type.

In the username and user, enter the username and password given by the ISP provider (Netcom, Great Wall, Telecom, Tietong, Cable, etc.) correctly. The connection mode selection is always filled in with the mtu value of 1492. The save is done.

4.Wireless routers also have a wireless encryption to ensure the user's wireless security. Select the wireless settings on the main page of the router's settings, select an encryption method in the security mode, any one of WEP, WPA, or WPA2, and then enter 8 or more Chinese characters or numbers as the wireless password in the security key, and the router settings will be completed after saving the settings.

5 After the setting is completed, the router will automatically restart, and the external network cable can be connected to the WAN port of the router to use.

Huawei HG232F 300M wireless router setup method:

Home Network Environment Cabling]:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter the Internet user name and password according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

Turn on the router's wireless function].

1. Select Wireless Settings --- Basic Settings.

2. Check [Turn on wireless function] and click Save.

Set wifi password].

1. Wireless Settings - Wireless Security Settings - Select [WPA-PSK WPA2-PSK].

Authentication Type: Automatic.

Encryption algorithm: AES.

The PSK password is the wireless password. Set the required password.

Today, a friend bought a Huawei wireless router, and asked me to help set it up, and solved it smoothly by referring to the following ** method, so I would like to share it for the convenience of friends who need it.

Method steps.

Get the router super password.

As a reminder, most routing ciphers have not been changed, and are uniform.

Account number: telecomadmin Password: ne7ja%5m

Router governance mode settings.

In order to configure a WBR-204G wireless router, you must know the governance IP address of the router. Huawei 3COMWBR-204G wireless router, management IP is, username and password are admin.

After connecting the router to the computer with a network cable, configure the IP address of the computer, and the IP address of the computer must be in the same network segment as the IP address of the router, that is, the IP address of the computer must be within the range.

After entering the router settings interface, click Network and Internet in the connection name

Record the parameters or simply take a screenshot (especially the LAN ID parameter and the multicast VLAN ID parameter>), then delete the item with the Internet, and create a new item >> the parameters are set as follows: Connection Type: Select Route; Select Internet for the list of services; Fill in the VLAN ID and multicast VLAN ID you just wrote down (each region is different, you must fill in the one you just wrote down); The IP acquisition method is changed to PPPoE; Enable NAT ticking; Fill in the username and password for surfing the Internet; Dialing method automatic The following figure shows the changed settings.

Advanced settings. The advanced settings of the WBR-204G wireless router are the same as those of other brands of routers, including WAN settings, LAN settings, and wireless settings. Each submenu is described in detail below.

WAN port setting options: WAN port settings are mainly used to configure the user's Internet access mode. Users can fill in the network access mode and related information they use. Take PPPoE virtual dial-up as an example to describe how to configure a WAN port.

After clicking "WAN port connection type", a drop-down menu will appear, select PPPoE, then fill in your Internet account and password, and click Save. The host name and PPPoE service name do not need to be specified.

After the setting is successful, the Internet device can connect to the router to access the Internet, and it is recommended to change the wireless router connection password to prevent the Internet from rubbing the Internet.

First, open the browser, enter the login interface in the address bar, and operate as shown below. (Set the password a little more complicated and memorize) and save the settings when you set them.

Hello! The steps to install and set up the Huawei HG232F router are as follows:

1. First of all, after connecting the wireless router, you need to check whether it is powered on and whether the wireless router is running normally.

2. After checking that it is correct, check the instructions on the bottom of the router, open the browser and enter the router IP, and then press Enter to enter, at this time a dialog box pops up, you need to enter the account name and password, there will be at the back of the router, in general: account name: admin password:

admin。

3. After entering the password behind the router, you can log in to the settings page of the router.

4. Click on the setup wizard on the page and follow its requirements step by step.

5. Click Next to enter the account password setting, this account password is the account password of the current network network, if you don't know, you can consult the network operator.

6. After setting the account and password for surfing the Internet, the function of wireless Internet access is set, set the wifi name and wifi password, it is recommended that the password is not too simple, it is easy to be cracked, and the encryption method can be recommended by the system.

7. Click Done, restart the router, and the settings have been successful.

This may have to be flashed to a firmware upgrade to crack! Flashing is risky, so be cautious.

The most beautiful thing is not the rainy day, but the eaves that have sheltered from the rain with you.

Here's how to set up a Huawei HG232F router:

1. Plug the network cable from China Unicom into the WAN port of the router, and connect the computer to the LAN port of the router;

2. Then set the IP address in the computer, the subnet mask and the gateway.

4. Generally, broadband is PPPoE dial-up Internet access, select "WAN port connection type" as "PPPOE", fill in the Internet account and Internet password provided by the service provider, and select "automatic connection, automatic connection after boot and disconnection";

5. Click "Save" and select "DHCP Server" on the page, click "Enable", fill in the start address (the minimum is and the end address (the maximum is, the address lease period is directly filled in the maximum value, and then click "Save" and select "Restart Router" under "System Tools" on the page, so as to complete the router setting.

Huawei 4G Router 2 can be set in the following ways:

1. Plug the network cable from the cat into any one of the network ports; If there is no computer at home, then plug the broadband network cable into the home in any one of the network ports;

2. Then connect the computer to the free network port with a network cable, and the complete connection can be shown in the following schematic diagram.

How to set up two wireless routers for wireless relay:

The first wireless router:

1.First, log in to the router that is connected to the Broadband Modem.

2.Set the SSID number and Channel in Wireless Settings - Basic Settings, and set the fixed channel number.

3.Set the wireless signal encryption information in the Wireless Settings - Wireless Security Settings to record the SSID, channel, and encryption settings of the wireless router after setting.

Second Wireless Router:

1.Log in to the second wireless router that requires a trunk.

2.In the network parameters - LAN port setting, change the IP address to be different from the first router (to prevent IP address conflicts), for example, save, the router will automatically restart.

4.Select the SSID number of the first router in the list of scanned signals and click "Connect".

5.Set the channel to be the same as the first router channel. At the same time, set the encryption information to be the same as the first router, and click "Save".

6.Shut down the DHCP server. In the DHCP server, select Disable, save, and restart the router.

7.At this point, the first wireless router and the second wireless router have successfully established WDS.