You can access the Internet through the cat, but the router can t, and you can t ping! 20

First, you should right-click on the online neighbor and select Properties. Right-click the local connection to select Properties. Locate the Internet Protocol. Once selected, fill in the selection attribute according to the IP that says on the router, so that you can enter the router.

After it's over, enter this address in the address bar to enter the router) pops up a thing that asks you to enter the username and password, this password and username are admin After entering this, select the setup wizard. Then the next step, then select ADSL virtual dial-up (PPPoE) and then enter the next step, and then enter your Internet account and Internet password, which you can fill in yourself, which is provided to you by the network ** provider. Then the next step, just keep it all the time.

Is this what you do, if you don't press the following to do it once, waste a few minutes of your time, ok, the network cable from the cat down is connected to the WAN port of the route, and then the line from 1234 is connected to your computer, and then set up the route, open**Write on the reverse side of your route, there will be a conversation to ask for the password and find it on the reverse side of the route (Mercury, Xunjie, TP Link routers are all and then the password is admin) in**After the point network parameters WAN port set pppoe The following is your Internet access and password, Netcom will use a special dial-up, and you will use the automatic point to automatically connect on the OK

If you can't connect at that time, turn off the cat and the router for 10 minutes, and then turn it on, if it doesn't work, restore the router to factory settings, that is, use a pen or a pointed thing to press the recovery button on the router for 20 seconds, release it, and then press the above settings to set it up from the new one (the point of router recovery is on both sides of the router, you see it's a small hole).

Done salute.

Routing is blocked by telecom You share routes across multiple computers Telecom is not allowed

You restore the router first, and then enter the route, fill in the username and password again and save it!

Is the DNS domain name set correctly?

You may be routing the wrong frequency band.

The question is not about a regular routed connection modem

And the "gateway" provided by the operator connects the router.

As can be seen in Figure 3.

The so-called light reed sail plum cat.

PPPoE mode has been enabled.

That is, "dialing is already used".

and successfully connected.

Therefore, the user can choose to accompany the late.

Use Secondary Routing or Use Routing as a Wireless Switch

First, use the secondary route, which needs to be set.

1. The WAN port of the router is set to: dynamic IP mode.

2. The router and the higher-level router cannot share the same IP segment as the car.

The router can be set to IP.

3. Other casual settings.

4. The WAN port of the router is connected to the LAN port of the "gateway".

Second, the wireless switch mode needs to be set.

1. The WAN port of the router is set up: dynamic IP

2. The LAN port IP of the router must be set to a different IP segment from the higher-level router, which can be set to and then restart the router.

3. The LAN port of the router cannot send DHCP

That is, turn off the DHCP function.

Remember not to restart the router.

4. Disconnect the route from the "gateway" before setting.

5. Other settings are arbitrary.

6. After the settings are complete, restart the route.

Then connect the network cable.

Connect the LAN port of the router to the LAN port of the gateway using a network cable).

There are three scenarios.

1. The router is not set up.

2. There is no computer setup.

3. Internet service providers disable routing.

Generally 1 and 2.

The routing settings are basically the same for each brand. It's just that the login method is different, as follows: TP's user admin password, admin (factory settings), Tengda's TP's user admin password, admin (factory settings), and the computer settings are as follows.

If you can't dial up the painting of the cat.,That's your own network can't get through.,Report for repair.。。

If you can't get into the drawing of the router, you can restore the factory settings, and then enter the " " "Username and password are:

admin..There is a small hole in the back of the router, poke it in with a toothpick, and keep holding it for about ten seconds before restoring the factory settings. If you still can't enter the router after resetting the factory settings, you can check whether the network cable connecting the router to the computer is broken, if the network cable is fine, it is a problem with the router.

I guess the IP address of the router in the cell is, you are connected to the route, and the IP address of your router is also conflicting.

You can log in directly with the cat, which proves my conjecture even more.

I don't know exactly what to do, but you can try:

Change the LAN port IP address of your router to the port connection status and set it to dynamic IP. (Be careful not to select PPPoE). Turn on your router's DHCP server. The address pool is to. The computer is set to automatically get an IP address.

If the cell is set with a static address and a MAC address is bound, then you can change the WAN port connection type of your router to a static IP. Also clone your computer's MAC address to the router.

What is new will be discussed.

When your router is reset to factory settings and the local connection is set to automatically obtain IP, can the local connection get the IP address? What is the IP address?

Sometimes my IE will be like this, no matter how I can't get in, my experience is to try with Firefox, that is, to try with a different core browser from the original, or maybe it works.

1. Determine whether the setting method after connecting the cat is the same as the setting method of the route after connecting the route, which is absolutely not the same (that is, the account password or IP setting or something) (after resetting, only these and the wireless part are set, and there are no other special requirements for Internet access, do not set others).

2. Go to someone else's house to try it (preferably Unicom, excluding telecom that has recently made some things to disgust routing).

3. Other people's homes are not good, and there is a routing problem.

According to personal experience, if the router can be set to not access the Internet, it is generally a setting problem.

Also, there is the automatic connection mode of routing, and sometimes it takes a long time to connect to find the right mode, which usually takes 5 minutes, more or less. You can go make a cup of tea or something, and then come back and see it.

Restore the router to factory settings and see, first of all, you can log in to access the router to indicate that the router is normal, dial-up to the Internet, you go to the router interface to see if the WAN port has been connected.

Do you want an account password for a linked cat? That is, every time you go online, you don't need to click on the broadband link.

If you want to, you need to set up PPPoE

If you don't just plug it in and use it, you need to use it through a bridge.

To restore to factory condition, take a needle, insert the reset hole with power on and hold for more than 5 seconds. Please refer to the router manual.

If nothing has changed, please set the network card address according to the requirements of the manual to enter the router settings interface. Note that the WAN side should not be plugged into the network cable.

The general setup of a router is like this, taking a wireless router as an example:

Connection: (refer to the router manual).

The network cable out of the cat is plugged into the WAN end of the wireless router (no network cable is plugged in when set), and the network cable of all computers is plugged into the LAN end of the router.

Settings: (refer to the router manual).

1.Set the WAN side of the router: Select PPPoE and enter the username and password.

2.Configure the LAN side of the router: Enable DHCP service.

3.Set the WLAN side of the router: Set the password, which is generally safer to use WPA now. Remember the name of the outgoing signal from the wireless router, and the password for backup.

4.Check to see if the cat's address is the same as your wireless router address, and if so, change your router address, for example, you can change yours.

5.Set all Internet devices to get addresses automatically.

Thank you for your question.

Factory router, go to router settings. If it is a number dialed by a cat, then the WAN port of the router will automatically obtain the IP, and if the router is dialed, then use the PPPoE mode.

If the ISP restricts the routing function, you won't be able to access it.