When printing, the printer can t absorb the paper, what s going on

It may be that there is a problem with the paper put in, there is too much paper or it does not meet the specifications, it may be that the paper is stuck inside the printer, resulting in the inability to feed the paper normally, or it may be that the ink runs out, and the printer will no longer automatically feed and print. Here's a closer look:

1. Check whether the printer you put in meets the standard, such as specifications or paper quantity, it may be due to too much paper, you can try to reduce a part of the printing paper.

2. Check whether there is paper clip inside the printer, if there is paper clip, turn off the power first, and then carefully pull out the jammed paper.

Reasons and solutions for not sucking paper:

1. Putting too much paper in.

1. First check whether the installation of the printing paper placed in the printer meets the standard.

2. If it is exceeded, the printing paper must be reduced. Remove a portion from the printer.

2. Blockage of foreign bodies.

1. See if there is paper clipping inside the printer.

2. If there is paper clipping, turn off the printer first.

3. Then carefully remove the foreign body.

1. If the quality of the copy paper is poor, or the paper is damp, replace the copy paper.

2. Stuck under the toner cartridge: It may be a laser.

It could also be.

There is a problem with the fixing module, and the fuser film inside is broken and needs to be replaced. Please check whether the paper roller of the machine is aging, if so, please replace it.

3. The rubbing roller of the carton is damaged, and the paper roller cannot be rubbed, so the paper roller can be replaced.

4. If the paper sensor is damaged, contact the after-sales service to replace the sensor.

Find a thick piece of paper, use a damp rag to wipe the paper into a tidal shape, then feed the paper, glue the paper powder out, and you can use it.

Solution:

1) Replace the copy paper.

2) Please check whether the paper roller of the machine is aging, if it is aging, please replace it.

3) Reach in with your hand from the paper feed port and touch the plastic paper guide piece to make it smooth and the machine recovers.

The main reason for this is on your computer. See if the plug is disconnected. Whether the line is in good condition. Whether the printer is broken. The printer is not stuck.

The printer feeds the paper normally, the solution is very simple, you take a damp rag and wipe the paper roller clean.

A different feed belt will do.

First of all, you have to make sure that you put the paper flat!!

Check if the printer is jammed.

It's jammed, take it out and put it anew. The paper must be put away.

Office staff often use printer equipment to print documents, etc., usually when the printer is printing, it will automatically feed the paper for printing, but some users encounter the situation of not feeding the paper, resulting in the inability to print, what is going on, there are many reasons for this problem, now I will share with you the solution that the printer does not automatically feed the paper.

1. Laser printer does not feed paper troubleshooting solution:

1. Whether the machine prints without paper feeding, whether there is a paper feeding action, and the sound of paper loading.

2. You can refer to the figure below to use a wrung out wet rag to wipe the paper roller of the paper box to increase the friction of the paper roller.

Note: The wiping process requires the printer to be powered off. The rubber material of the paper roller is generally jagged and the surface is rough, and the purpose of this operation is to increase the friction of the paper roller. The paper roller is generally on the paper box, that is, near the place where the paper is placed, and some cases are given for your reference.

Example 2: Xiaoxin printer.

Example 3: Printers without paper trays, such as M7206, M7216, M7256, LJ2205, LJ2206, etc.

3. Plug in the power supply after wiping and turn on the machine, and try to print the machine self-test or copy after turning on to see if the machine can load the paper normally.

4. If it still can't be solved, it is recommended that you contact the printer for after-sales processing.

Second, the dot matrix printer does not feed the paper for troubleshooting.

Dot matrix printers and laser printers are different, it usually uses a sensor to detect the paper, if you encounter the problem of not feeding the paper;

1. First of all, you can wipe the paper detection sensor of the printer with an eye cloth or something;

2. Disconnect from the computer first, and only connect the printer power cord. After turning on the machine, put the paper to see if it can absorb the paper normally, if there is no suction paper, you may need to take it to the repair station for maintenance.

The above is the detailed troubleshooting method of the printer does not feed the paper, if you encounter the same fault, you can take the above methods to solve it, if it cannot be solved, it is recommended to send it directly to a professional for repair.

This may be due to the loose pulley inside the printer. As a result, it is difficult for the paper to suck up, so it is recommended to take it for repair.

First of all, confirm whether your printing paper meets your printer's standard paper range, and secondly, you need to check whether the paper roller and the placement of the paper are strictly implemented in accordance with the operation process in the instruction manual, and whether the paper roller is clean.

1 is related but not necessarily a problem with this sensor.

2. It is possible that the paper is too soft to trigger this sensor well.

3. Replace some paper and try it It is best to consider replacing the sensor again.

Reasons and solutions for not sucking paper:

1. Putting too much paper in.

1. First check whether the installation of the printing paper placed in the printer meets the standard.

2. If it is exceeded, the printing paper must be reduced. Remove a portion from the printer.

2. Blockage of foreign bodies.

1. See if there is paper clipping inside the printer.

2. If there is paper clipping, turn off the printer first.

3. Then carefully remove the foreign body.

Reasons and solutions for not sucking paper:

1. Putting too much paper in.

1. First check whether the installation of the printing paper placed in the printer meets the standard.

2. If it is exceeded, the printing paper must be reduced. Remove a portion from the printer.

2. Blockage of foreign bodies.

1. See if there is paper clipping inside the printer.

2. If there is paper clipping, turn off the printer first.

3. Then carefully remove the foreign body.

1. Putting too much paper in.

1. First check whether the installation of the printing paper placed in the printer meets the standard.

2. If it is exceeded, the printing paper must be reduced. Remove a portion from the printer.

2. Blockage of foreign bodies.

1. See if there is paper clipping inside the printer.

2. If there is paper clipping, turn off the printer first.

3. Then carefully remove the foreign body.

The printer does not absorb paper and does not serve paper.

It is possible that your printer's paper roller is slipping, please wipe the paper roller with a damp cloth.

Method 1: Follow the promptsWhen the printer is out of paper, a prompt will appear on the computer. At this point, after placing the paper in the printer's paper drawer, click the "Retry" button, and the printer will continue to print the remaining print jobs smoothly.

If you have closed the status message window, refer to Method 2 or Method 3.

Method 2: Turn on and off the top cover of the printerWhen the computer does not display the status message of the printer or the status message has been turned off, turn the top cover of the printer on and off again. Wait for a while, the printer will automatically return to the normal printing state, and the unfinished printing tasks will be printed one by one.

Method 3: Cancel the print schedule After the operation of method 1 or method 2, the printer still cannot print, then you can only cancel the unfinished print job first, and then send the print job again. Please follow these steps:

1.Fill the feed tray with enough paper.

2.Power off the printer.

3.Manually clear outstanding print jobs. For details about how to manually clear print jobs, see Clear Unfinished Print Jobs.

4.Turn on the power of the fiber printing machine. 5.Send the print job again and you will be able to print normally.

Solution: Find a thick piece of paper, use Zheng rent imitation wet rag to wipe the paper into a tidal way, and then feed the paper, and stick the paper powder out to use.

When printing, the printer cannot absorb the paper because the printer driver is not installed normally, and the normal installation steps can be solved.

When printing, the printer cannot absorb the paper and the solution is as follows:

Materials to prepare: computer, device manager.

1. Right-click the mouse for computer management.

2. Open Device Manager.

3. After opening the "Device Manager" interface, check whether the relevant printer driver in the "Print Queue" list is installed normally, if not, you need to install the printer driver important.

4. You can also use computer driver detection and installation tools such as relevant driver wizards or driver life to try to repair the computer printer driver.

<>6. From the open "System Services" list, find the "Print Spooler" service item, if this service is not opened normally, then directly right-click and select the "Open" item, which solves the problem that the printer cannot absorb the paper when printing.