The steps to set up the router on the desktop computer go to 192 168 0 1 should be explained step by

1. At present, the address of the conventional brand of wireless routers on the market.

2. The laptop or desktop computer is connected to the LAN port with a network cable, and the broadband modem or the network cable provided by the operator is plugged into the WAN port.

3. Make sure that the laptop or desktop has obtained the IP address from the router, and individual routers need to set an IP address on the same network segment as the router for the machine.

4. Most routers have a setup wizard, if you don't have one, find the WAN settings and enter the broadband password. There are three modes here, one is PPPoE, which is the ASDL we commonly use, and the other is static IP, which is mainly the IP address assigned by the superior network on this main network line, enter the IP address assigned by the superior network, subnet mask, default gateway (when the default gateway conflicts with the local network, the address of the local LAN must be modified), and the third is the dynamic IP, which is generally the network cable assigned to you by the operator, using the temporary Internet IP or the upper network assigned to you.

5, this input is complete, click Save, find the wireless security settings, one is to set the SSID, which is what we often call the name of the hotspot, the other is to find the wireless security password option, at present, most of the WPA2 mode is selected, it is generally recommended to add numbers to English. Click Save.

6. There is a system status option on any router, check whether the WAN link has a public IP (usually 11x or 22x) starting with it.

7. At this time, use your laptop or mobile phone to find the SSID name you set, and enter the password. If a signal grid is displayed and there is no exclamation mark, you can browse the web.

The following is an introduction to the Xunpla router setting method for reference

The first step is to connect the line.

Before there was no router, we directly connected to the broadband through the computer, so now we want to use the router to share broadband Internet access, of course, we must first use the router to directly connect to the broadband. Therefore, the first step to do is to connect the line, connect the front-end broadband modem output network cable to the router (WAN port), and then connect the computer to the router (LAN port), as shown in the following figure;

Step 2: Open the browser, open the browser, clear the address bar and enter the management address: "Or Enter, the initial login interface needs to set the management password of the router, and then you can enter the management router with this password, please be sure to keep it in mind.

After setting the password, click "Next" as shown in the image below;

Step 3: Set up the router according to the setup wizard: the router will automatically detect the Internet mode, after confirming the Internet mode, please enter the broadband account and password provided by the operator, and click "Next", as shown in the figure below;

Step 4: The next step is to set up the wireless network, that is, to create a wifi network, mainly fill in the wifi name and create a wifi password (the password is recommended to be as complex as possible to prevent being rubbed on the network)'. Set the "wireless name" and "wireless password" of 5G respectively, and the wireless name It is recommended to use a combination of numbers and letters, do not use Chinese or special characters, and set a wireless password of 8 digits or more.

Click "Next" as shown in the image below;

Step 5: Click "Confirm" to complete the setup wizard, as shown in the figure below.

Step 6: Confirm that the setting is successful: After the setting is completed, enter the router management interface, and in the "Common Settings" > "Internet Settings", if a tick is displayed on the Internet settings icon, it means that the network connection is successful.

At this point, the router has been set up. After the computer is connected to the router, there is no need to dial up the broadband connection, and you can directly open the web page to surf the Internet.

If you have other computers that need to access the Internet, you can directly connect the computer to any LAN interface with a network cable to try to access the Internet, and you do not need to configure the router. If it is a wireless terminal such as a laptop or mobile phone, you can connect the wireless signal of the router to the Internet directly.

The router's cable does not need to be connected to the computer.

To connect to the router, you can log in to the gateway IP address to access the gateway.

Both wireless and wired routers can access the gateway normally.

The gateway configuration interface of the wireless router is rented

2.Open the computer browser and enter the gateway IP address of the nameplate behind the router (generally, enter the password of the router manuscript car account, and the nameplate on the back of the router is written.)

3.Go to the gateway configuration page.

Not necessarily, only the router that is set up for the first time, after reset, or fails, must specify the IP address of the computer network card before you can log in to the router settings page normally and use the setup wizard to set up, except for smart routers; For example:

IP: or.

Font code: Gateway: or.

If you are satisfied, please give points!

The router's cable does not need to be connected to the computer.

To connect to the router, you can log in to the gateway IP address to access the gateway.

Both wireless and wired routers can access the gateway normally.

How to open the gateway configuration interface of the wireless router:

2.Open the computer browser and enter the gateway IP address of the nameplate on the back of the router (generally, enter the router account password, and the nameplate on the back of the router is usually written.)

3.Go to the gateway configuration page.

If you can't open the router settings after connecting, you can first clear your computer's IE cache (cache,) This is very important. Lighting up is a must, if the light is not on, it proves that there is no connection, and it will be displayed in the lower right corner of your computer.

It is necessary to connect to enter, the password is the default, just press the next step.

Not necessarily, there is also a wireless connection.

You mean the IP of the router to which the computer is wired? That requires you to log in to the route first,Set it in the leftmost column,The default should be,You can modify it and save it.,And you can also set your computer to automatically get the IP segment of the IP.,There's an IP pool in it.,Just set it up.,I don't know why you modify this IP address? It's useless.

Go to the router settings from your computer and change the IP address of the router in the settings.

Not necessarily, only the router that is set up for the first time, after reset, or fails, must specify the IP address of the computer network card before you can log in to the router settings page normally and use the setup wizard to set up, except for smart routers; For example:

IP: or.

Font code: Gateway: or.

If you are satisfied, please give points!

Router to router, second router setup, there are two ways:

The first method: dynamic IP mode (the first route is the primary route, and the second route is the slave route).

1. Plug in the router and do not connect the LAN port of the main router first, and reset the slave router (restore the factory);

2. Connect the computer from any LAN port of the router to enter the settings page;

3. Set according to the dynamic IP;

4. Then set the SSID, encryption method and password;

5. Save and restart;

6. After setting, connect the network cable from the LAN port of the main router to the WAN port from the router.

The second method: wireless AP mode.

1. Connect the computer to the LAN port of the router first, and change the IP address of the slave router. For example, most router addresses are, we just need to change from router IP address to that;

2. Turn off the DHCP function from the router in the settings;

3. Finally, connect the network cable from the main router to the LAN port of the slave router (any one is fine), note that it cannot be the WAN port.

If it can't be connected, the first three numbers must be different, and the third one is generally changed.

The first router is connected to the external network, as long as it is set up normally, and the second router and the first router can be connected with a LAN port or a wireless bridge.

It is best not to set 2 routers on the same network segment.

What are you doing here, Relay? For relays, please take a look at the tutorial, poof

How you plan to use the two routes.