How to paste wallpaper How to paste wallpaper?

Wall treatment: use scrapers and sandpaper to remove impurities and floating soil on the wall, and repair and smooth the holes and cracks with gypsum powder. If the wall is soft or has a powder layer, you should first apply the wallpaper glue to make the wall firm, so that the wallpaper will not fall off.

Cut the wallpaper: Measure the height of the wall first, and then cut the length of the wallpaper. There are two scenarios:

Do not cut the flower wallpaper according to the height of the wall about 10 cm in length, as for the upper and lower trimming; The symmetry of the pattern needs to be considered for the flower wallpaper, so the cutting length should be increased according to the actual situation, usually more than 10 cm long.

Brush glue: Brush the wallpaper glue on the back of the cut wallpaper with a brush, and pay special attention to the surrounding edges to be coated with glue to ensure the quality of construction. After the painted wallpaper, fold the glue side and leave it for 5 minutes, so that the glue can completely penetrate the bottom of the paper before it can be posted.

Paint several pieces of wallpaper at a time and post them in order.

Wallpaper construction: use a crosshair hammer to measure the vertical baseline, post the first wallpaper from top to bottom according to the baseline, squeeze out bubbles and excess glue, and make the wallpaper flat and close to the wall.

Trimming and cleaning: cut off the excess wallpaper at the upper and lower ends, the knife should be sharp to avoid burrs, and then use a cleaning wet towel or sponge dipped in water to completely wipe the glue remaining on the surface of the wallpaper to avoid the wallpaper turning yellow.

If there are air bubbles on the surface of the wallpaper after drying, cut it with a knife and inject glue and then flatten it to eliminate it.

Power switch and socket pasting: first turn off the main power, then cover the wallpaper over the entire power switch or socket, cut out two diagonal lines from the center point, 4 small triangles will appear, and then use a utility knife to cut off the excess wallpaper along the power switch or socket. Finally, use a rag to wipe off any excess adhesive.

Wallpaper is beautiful and durable, washable, has a long life and a wide variety of patterns, and has become a must-have for many home decorations. The method and process of pasting wallpaper should be carried out according to the following steps: first level the wall, hit putty, smooth the wall with sandpaper after the putty is dry, and apply glue to the bottom layer to play the role of moisture-proof and dense wall.

Then soak the cut wallpaper in water for about 5 minutes and take it out, brush on the special wallpaper glue, use a scraper to stick the wallpaper to the wall, and smooth out the bubbles with a rag. Then overlap the next wallpaper by 2 cm and paste it, cut it from top to bottom with a paper knife in the overlapping part, tear off the remaining paper to make the splicing seamless, and finally wipe the excess glue at the joint with a wet towel. After the completion of the pasting of the wallpaper on the flower tight, smooth and beautiful, people standing about 1 5 meters away from the wall visual inspection, should not see the joints, no bubble folds.

Tools: Materials:

4"Large oil sweep.

Wallpaper. Wallpaper scrape.

aleurone (for wallpaper).

1"Aluminum ruler.

Whitewater. Kosuke knife.

Varnish. Wet white towel.

Heaven takes water. Method.

First press 1 with white water

Add 10 proportions of water, paint the wall, remove the old paint as soon as possible, and re-plaster.

On the wall that has been polished, apply a layer of varnish to prevent moisture.

Remember to add 1:

1 proportion of Tianna water diluted;

Remember to wait until it is dry before sticking it.

Measure the size of the wallpaper and reserve at least 4 inches in length.

Use an oil sweep to evenly spread the paste on the back of the wallpaper, and paste it after about 5 minutes, starting from the middle of the wallpaper and reserving 2 inches at the top.

Sweep the wallpaper scraper from the inside to the outside to eliminate air bubbles and wrinkles. Use a damp towel to wipe the edge of the wallpaper or the paste between the wallpaper.

If you buy wallpaper, you will send glue, first clean the wall and make it smooth!

Then apply it again with glue. Spread out the wallpaper and apply it with glue. Then stick it on the wall. Paste it and use a flat wooden board to smooth out the wallpaper.

First, flatten the wall with 240 sandpaper and wipe it clean.

Cut the first piece of paper to be pasted, put it flat and moisten it with a towel, brush the place to be pasted on the wall, and then brush the wallpaper with glue again, and you can paste it.

Stick the paper to the wall and scrape it flat with a rubber scraper, and then press it with a dry towel.

If there is air in the area, prick it with a needle and squeeze it out.

Dilute with white glue and roll glue on the wall with a rolling hole, soak the wallpaper with water and then stick it to the wall, and scrape it flat with a plastic scraper.

Do you know what wallpaper is? Wallpaper is a decorative object that is pasted on the wall. Nowadays, many people will use wallpaper at home, there are many types and styles of wallpaper, and the methods of different types of wallpaper stickers are also different.

When we choose wallpaper, it is best to choose some wallpaper that can be waterproof, so that our home is not afraid of moisture. Sticking wallpaper is a more professional job, and I replied that we generally have to invite some professionals to come and paste. Below, let's take a look at the steps to put wallpaper.

1. Mainstream factions.

Wall stickers are divided into three mainstream factions in the world: Chinese wall stickers, European and American wall stickers, Korean wall stickers, and wall stickers.

2. Features. Wall stickers are very suitable for busy and the pursuit of taste of exquisite life, fast-paced life is fast and easy, a beautiful pattern that has been carved only needs to be pasted on the position that needs to be decorated, compared to the decoration team to design and produce a higher cost of decorative wall, it is really convenient and practical. Pasted on surfaces of smooth textured materials such as walls, glass, tiles, refrigerators, air conditioners, cabinets, furniture, etc., coated with latex paint.

Considering the differences in walls, it is recommended that the wall of special materials or the wall of a relatively long time can be picked a corner first).

The service life of wall stickers has a certain relationship with the use environment, and generally speaking, there is no problem to use it for more than 5-6 years. The wall stickers are waterproof and do not fade, and can be pasted in the shower room, kitchen and bathroom. However, before sticking it indiscriminately, you must use a dry rag to wipe off the stains on the veneer before pasting, which will keep it firmly.

If it is dirty, you can wipe it with a damp cloth, which is very convenient. Wall stickers generally use PVC vinyl material, the outstanding advantage is the use of non-toxic plasticizers, flame retardant, wear-resistant, chemical corrosion resistance, low gas and water vapor, in the domestic designated manufacturers to produce home interior wall decoration special PVC self-adhesive materials, 100% in line with the European Union's environmental protection standards, green, healthy, pure color and waterproof does not fade, after the wall viscosity can generally be maintained for more than 6 years.

3. How to paste wallpaper.

1. Choose the location of the sticker first, and then wipe the dust or oil stains on the wall, glass, furniture, etc.

2. Hold the sticker first to compare how to paste it best.

3. When you start pasting, paste the middle first and then press it left and right.

4. If you feel that the position is not satisfactory after pasting, please tear it off slowly and change the position and then paste it, if there are bubbles after pasting, you can use a needle to prick it and run away the air.

Now do you know anything about wallpaper? Wallpaper is more professional, it is difficult for us to carry out the actual operation ourselves, and it generally takes two or three people to paste the wallpaper of a wall. When we paste wallpaper, we must pay attention to safety, because the wall is relatively high, and we generally need to step on the ladder to paste wallpaper.

Wallpaper also needs some cutting tools, when we paste wallpaper, we must first prepare the tools for wallpaper, so as to prevent us from being in a hurry when we paste wallpaper.

Decorating a house is to design the wall, but there are more ways to design the wall, so it is best to see what styles are suitable first, but the wallpaper is now more popular with people, but it is also necessary to pay attention to the wallpaper, thenHow to paste wallpaperWhat are the methods? What should I pay attention to when pasting wallpaper? Let's introduce it to you.

1. How to paste wallpaper.

1.Remove the wall skin: remove the original paint and other objects on the wall, use gypsum powder to supplement the cracked parts of the wall, and apply bandages after leveling; If it is a sand-gray wall or partition wall, it should be covered with glass silk cloth or really good cloth.

2.Cutting wallpaper: Measure the height of the wall first, and then cut the length of the wallpaper, before construction, you should carefully check whether the color number and batch number of the wallpaper are consistent.

And to understand the type of wallpaper to be constructed, the color paper needs to be on the flower, and the symmetry of the pattern needs to be considered, so the cutting length should be increased according to the actual situation, usually 8 to 10 cm longer.

3.Brush the base film and glutinous rice glue: The quality of the base film and glutinous rice glue will directly affect the overall effect and service life of the wallpaper, so it is necessary to buy the base film and glutinous rice glue of authentic brands.

The main function of the base film is to protect the wall, prevent water and alkaline substances from penetrating the wall, and play the role of moisture, mildew and alkali.

Second, the precautions for sticking wallpaper.

1.We should pay attention to the air humidity in the living room before pasting wallpaper, which will affect the quality of wallpaper. Usually the air humidity is below 85%, so it is important to prevent wallpaper installation during the wet season and on wet walls.

It is necessary to ensure that the wall is flat, boring, and free of dirt and floating dust, so as to ensure that the wallpaper is paved beautifully and is not easy to blister and warp.

2.Apply a layer of polyester paint on the wall before paving, the main function is to prevent the wallpaper from being damp and mildew in the future, affecting the service life, and preventing the time-consuming and laborious replacement of wallpaper in the future. When sticking wallpaper buckets, there is usually adhesive liquid overflowing, which should be wiped clean with a clean towel at any time, especially the glue marks at the joints of wallpaper and wall cloth should be treated cleanly.

3.Try to ensure that the wallpaper is as clean as possible, and if the wallpaper is stained, it should also be cleaned with soapy water or detergent in time. After the wallpaper is pasted, the doors and windows should be opened during the day to maintain ventilation, and the doors and windows should be closed at night to prevent moisture from entering.

It should also be empty to prevent the wallpaper just pasted from being invaded by strong winds, otherwise it will affect the firmness of the wallpaper.

4.Vacuum the wallpaper regularly, and be careful to change the suction head of the vacuum cleaner. Usually found that the wallpaper is dirty, it needs to be wiped in time, the water-resistant wallpaper can be wiped with water, and it can be blotted dry with a dry towel after washing; Wipe the water-resistant wallpaper with an eraser, or wring it out with a towel dipped in some cleaning solution.

When the house is decorated, the wallpaper will be designed and installed, but the wallpaper will be more troublesome, so how to paste wallpaper and what are the precautions for wallpaper, then we have read the above introduction, and we have also understood it, so if you still want to know more decoration information, please continue to pay attention to it.

Wallpaper is no stranger to all of us, and now many families are using it to decorate their houses. Wallpaper can add beauty to the interior, and many people now love it. Nowadays, there are many types of wallpaper, but when pasting wallpaper, many people do not post the desired decoration effect because they do not know how to paste it.

And the precautions for sticking wallpaper!

1. Fill the hole in the wall with putty and level the wall with a scraper.

2. Measure the size of the wall, and then measure the wallpaper based on the wall area, pay attention to the length of the wallpaper, which is 5cm more than the actual veneer.

3. Then mix the powdered wallpaper glue with water and mix the general wallpaper with 1:3, and the foamed wallpaper with 1:2, or use the special glue for wallpaper that does not need to be prepared, and evenly brush the back of the wallpaper with the special glue that has been blended with a roller brush.

Face. 4. Then lean the wallpaper against the wall, and paste it from top to bottom and from the corner to the inside with a wooden handle brush, so that the wallpaper will be leveled.

5. When encountering a power switch or socket, cover the wallpaper first and then brush it flat with a wooden handle, and then use a utility knife to draw a cross on it diagonally, use a scraper against the edge of the switch, and use a utility knife to cut off the excess part.

6. If you encounter a connection by the printed wallpaper, find the consistent position of the pattern at the junction of the two wallpapers, overlap and paste about 12cm wide, and after the whole wallpaper is all aligned, use a scraper to resist, and then cut off the overlapping part with a blade.

7. Pay attention to pasting wallpaper from top to bottom, if you find that the floating paste is uneven, you can use a towel to wet it, and then re-level it with a scraper.

8. Finally, the wallpaper around the door and window is processed in the same way as the wallpaper at the power switch.

9. After the wallpaper is pasted, the original device is installed.

Precautions after pasting wallpaper.

1. After the completion of the wallpaper project, the doors and windows should be opened during the day to maintain ventilation; Close doors and windows at night to prevent moisture from entering. Rashen.

2. Avoid the wallpaper just pasted from being invaded by strong winds, otherwise it will affect the firmness of the wallpaper.

3. Vacuum and clean the wallpaper regularly, and pay attention to changing the suction head of the vacuum cleaner.

4. When you find that the wallpaper has special dirty stains, you need to wipe it in time, and the water-resistant wallpaper can be scrubbed with water, and you can use a dry towel to blot it dry after washing; Wipe the water-resistant wallpaper with an eraser, or wring it out with a towel dipped in some cleaning solution.

5. Avoid hitting and rubbing wallpaper with hard objects in daily life.

If you want to put wallpaper at home, you need to learn how to stick wallpaper, only in this way can you decorate your home better. It is also the end of the precautions on how to paste wallpaper and Jiye wallpaper introduced to you.

Many owners feel that wallpaper is simpler than brushing paint, as long as the wall is kept flat and clean before construction, in fact, it is not a simple thing to pave wallpaper. SoHow to paste wallpaper？Below we will bring you the most detailed and comprehensiveSteps to paste wallpaper

Paste wallpaper step 1, on-site inspection and signing

Check that the wallpaper purchased is complete and consistent with the quantity purchased. Check whether the construction accessories are complete. Such as glue powder, glue paste, protective tape, etc.

Pay attention to whether the wallpaper and adhesive paste have the "F Certification Standard" certification. The "F Certification Standard" is currently the highest environmental rating recognized worldwide and can only be achieved by bonding solid wood and formaldehyde-free adhesive.

Paste wallpaper step 2, check the quality of the wall

The construction wall is required to be clean, strong, flat, dry, moderately absorbent, and neutral pH. Check whether the wall meets the above requirements. Generally, after the wall is coated with interface agent (moisture-proof material), it must be dried naturally for more than 15 working days.

Step 3 of wallpapering, do a good job of ground protection

Generally, when the wallpaper is laid, the floor has been paved with floor tiles or floors. It is recommended to spread a layer of plastic film on the floor before laying wallpaper. Applying a film protects the floor by preventing the glue from falling directly onto the floor.

Paste wallpaper step 4, measure the size again

Measure the size of the wall to find out how much wallpaper you need. The width of the wallpaper without the protective edge is the shortest effective distance of the wallpaper, and the position from the top of the wall to the baseboard is the height of the paving, which is also the shortest effective distance of each wallpaper.

Step 5 of wallpaper pasting, start wallpaper cutting

When cutting wallpaper, a single piece needs to be larger than the actual wall length, and the general distance is about 10 cm. The remaining parts of the wallpaper can be retained for later repair. If a complete wall, there is an additional location (e.g.

beams), which are usually not paved, and the effect is better.

Step 6 of wallpaper, glue and soften the wallpaper

Use a scraper to evenly apply the glue to the back of the wallpaper, glue and attach a protective tape and fold the wallpaper in half to allow the wallpaper to soften for a while. During the gluing process, the orange protective tape is paved to ensure that there will be no rock glue on the surface layer of the wallpaper when folded in half.

Paste wallpaper step 7, wallpaper paving

When laying wallpaper, you can judge the horizontal and vertical of the wallpaper with the help of instruments, and pay attention to leaving a surplus at the upper and lower edges. When laying wallpaper, pay attention to timeliness. If the glue starts to dry out and firm, do not lift the wallpaper for correction.

Paste wallpaper step 8, wallpaper trimming and cleaning

Pay attention to the stitching of the pattern in the overlapping parts and cut the overlapping parts of the wallpaper. At the wire switch panel, straighten as far as possible. The glue scraped from the wallpaper splicing and the glue on the panel can be wiped with a sponge.

Wallpaper step 9, paving is completed to confirm

The owner needs to accept the wallpaper pavement and properly keep the relevant coarse documents that have been signed and confirmed, especially the warranty certificate. Because it involves future maintenance and warranty issues, it needs to be treated with caution.

That's all for youHow to paste wallpaper？The most comprehensive wallpaper steps in their entirety.