How do you install a tent? How to install a tent

How to install a tent hundred:

1. Take out the tent from the outer bag first, note that there are 2 black bags inside, the big one is the tent pole, the small one is the ground nail and windproof rope, and then spread the tent on the ground, and put aside the nail bag, rod bag and other accessories wrapped together with the tent.

2. Take out the fiberglass rod from the rod bag, dock it well, and turn it into a whole long rod.

3. Thread the docked fiber pole into the pipe of the tent, and some double-layer tents are hung inside, so hang the hook on the fiber pole. Several rods should be worn at the same time.

4. Insert one end of the fiber pole into the shed circle at the bottom corner of the tent, and then at the other end (diagonally), hold the rod in one hand and the bottom corner of the tent in the other, slowly arch the pole, and then insert the rod into the shed at the bottom corner after the tent is propped up.

5. The last step is to hit the nail and pull the camp rope, it is best to use force, and the angle should be right, so that the tent that is propped up will be firm and beautiful, and the residence will be comfortable.

A tent is a shed that is propped up on the ground to shelter from wind, rain, and sunlight and for temporary living. It is mostly made of canvas, and together with the supporting things, it can be removed and transferred at any time. Tents are carried in the form of parts, and they are assembled when they arrive at the site, so various parts and tools are required.

Knowing the names and how to use each part, and being familiar with the structure of the tent, can you set up the tent quickly and easily.

Here's how to install the tent:1. First of all, pull out the loop rope close to the end rope tail in the wind rope slide of the tent, as shown in the following figure

2. Then use it to lasso the ground nail, as shown in the figure below

3. Then select the position of the ground nail according to the ground situation, generally speaking, the smaller the angle between the windproof rope and the ground, the better the wind resistance of the tent, and insert the ground nail into the ground at an oblique angle of 45 60 degrees, so that the force is the largest, as shown in the figure below:

4. Then adjust the tightness of the wind rope, as shown in the figure below

5. Release your hand, if the whole tent rope is still very tight, it means that the windproof rope is set up, as shown in the figure below

The outdoor tent installation method is as follows:1. First of all, pull out the loop rope close to the end rope tail in the wind rope slide of the tent, as shown in the following figure

2. Then use it to lasso the ground nail, as shown in the figure below

3. Then select the position of the ground nail according to the ground situation, generally speaking, the smaller the angle between the windproof rope and the ground, the better the wind resistance of the tent, and insert the ground nail into the ground at an oblique angle of 45 60 degrees, so that the force is the largest, as shown in the figure below:

4. Then adjust the tightness of the wind rope, as shown in the figure below

5. Release your hand, if the whole tent rope is still very tight, it means that the windproof rope is set up, as shown in the figure below

Here's how to set up a tent:

Tools: tents, base cloths, tent poles, ground nails, anti-shelter wind ropes, corner nails.

1. Choose a good location first, identify the wind direction and terrain, choose a flat place, and clean up the debris on the ground.

2. Check the tent utensils. Pour out the supplies stored in the bag, check each part one by one, and put the extra nails in the bag for the convenience of scattering the tent cage and not missing things.

3. Lay the mat. After the mat is laid, spread the bottom of the tent on top of the mat and tidy it up.

4. First check and verify the passage of the tent pole through the Li Wang tent pole on the top of the tent brigade, and then pass the tent pole through the holes at both ends of the tent corner to support the tent brigade, so that the main body of the tent brigade is formed.

5. First fix one corner of the tent with a ground nail, then fix the ground nail at the other end of the diagonal, then fix the two ground nails next to it, and finally fix the rest of the ground nails.

6. The end of the windproof rope is fixed with ground nails, and the windproof rope is the most firm at an angle of 90° with the ground nails.

7. About 30 cm away from the tent, dig a drainage ditch about 10 cm deep, and the drainage outlet of the drainage ditch is selected at the lowest place.