How to engage in telecom fiber optics with cats to set up routers and computers

1.Plug the broadband modem or home network cable into the WLAN port of the router, and then connect to the computer through the network cable or wireless network.

3.After entering the page, you will be prompted to enter management, which also needs to be found in the manual, and the general password is admin.

4.Click on the Setup Wizard, follow the prompts on the page to set up broadband without oppoe dialing, and enter the broadband password.

5.According to the prompts on the page, check the box to turn on the WiFi network, and set the password, when finished, click Next, and the device will automatically restart.

Hello: You first connect the device as shown below.

Then in the case of not connecting the optical modem, set the LAN port setting of the wireless router, set the IP address to it, and then connect the optical modem, and then you can enter the wireless router, and then you can set other items on the router, enter the setup wizard interface, select PPPOE dial-up Internet access to fill in the Internet account and password, this should be understood by everyone, there will be an account number when opening broadband, you can fill it in.

We'll be happy to answer your questions. Based on the information you provide. Recommended:

1. Wireless devices access the Internet through wired broadband, and equipment supporting wireless transmission function is required. For example: wireless modem, wireless router, AP, etc.

2. At present, most families use ordinary cats and wireless cats. If you are using a wireless modem, you can change the configuration of the wireless modem or install PPPoE dial-up software to achieve wireless Internet access. If you do not modify the configuration parameters of the wireless modem to achieve wireless Internet access, you can also purchase a wireless router of a related brand to build a wireless environment.

3. The basic process of setting up the cat to connect to the wireless router is as follows: connect the LAN network cable of the cat exit to the uplink interface (WAN port) of the wireless router, log in to the wireless router configuration interface through the PC, and modify the configuration of the wireless router. Generally, you need to set up WAN port, LAN port, wireless menu and other related settings.

Specifically, you can refer to the relevant model router manual configuration, or you can consult the relevant brand after-sales service for guidance configuration.

4. After the wireless router is configured, you can connect by setting the SSID and key of the relevant wireless device, and it can be used normally after the normal connection is successful.

At present, Anhui Telecom Network Department carries out relevant mobile phone preferential activities. If you need to buy a phone, please log in to the Anhui Telecom network hall** to buy the latest mobile phone. If you need to check the bill and pay the phone bill, please log in to the online business hall of Anhui Telecom, and get 2 yuan for 100 yuan.

Follow the steps of the router manual to install and set up the router, and you can keep me private if you don't understand.

If you need to set up, you can dial 10000 to ask the working orange high staff to help the user set up, if you are setting up a router, you need to enter the cheat key behind the router account name and password.

Regardless of the port from which the router receives the packet, it extracts the destination IP address and the source IP address of the packet: and then decides if, how, and which port to go to based on the routing table and routing policy.

<> details are as follows: The optical modem itself does not have a routing function (bridge mode), and directly connects the optical modem to the WAN port of the router with a network cable.

The router sets up the dial-up connection (PPPOE), input, password; Then set the wireless name and save the password.

If it is a regular telecom mobile or Unicom optical modem, the routing function has been turned on; Even if you don't have a router, you can connect to the wifi to go online, and then add the router to set it up in 2 steps.

First, the router is not connected to the optical modem, directly enter the management interface, set the Internet modem: automatically obtain the IP method, and then set the wifi name, password, and save.

If the IP address of this router is not a network segment, you can directly plug in the network cable and connect it to the optical modem.

If the IP address is the same, you need to reconnect to the Wi-Fi, enter the management interface again, and set the third digit of the LAN port IP address to not be the same as that of the modem (to prevent conflicts with the IP address of the optical modem, resulting in Internet access at that time, but you can't access it after a period of time).

After setting OK, save it, and then use a network cable to connect the modem to the router to use.

Then open the browser, enter generally, or, (see your manual) enter the management and password, generally admin, enter the setup wizard, fill in step by step, according to your broadband** to make a choice, if it is adsl, you need to fill in the username and password, if it is a fixed IP address or not a fixed IP address of broadband, you have to fill in the necessary information, fill in all the way, very simple. For the security of data and wireless network, you go to the special wireless column to start the key, generally choose the wep method, fill in the key you want to set, pay attention to the number of key bits, see your page prompt, and then select the route in the route to restart, not manual power off, and then it's OK, search for the routing signal, enter your preset password everything OK! Hope it helps.

Home Network Environment Cabling:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Router Settings:

1. Check the router management address on the router shell label, there are two types of management addresses, please be sure to fill in the actual information. After entering the address in the browser, set the administrator password, and continue to set it (the default username and password of some routers is admin);

2. After entering the management interface, click Next to start the setup wizard, and select PPPoE (ADSL virtual dialing) in the Internet mode;

3. Enter the broadband account provided by the broadband operator in the Internet account and the broadband password in the Internet password;

4. Wireless settings: Set the wireless network name in the SSID, and set the wireless password of no less than 8 digits in the PSK password (it is recommended not to set the SSID to Chinese or special characters.) If the PSK password is set to 8 digits or more, be case-sensitive. ）；

5. Click Done, and the router is set up successfully. At this time, the computer that needs to access the Internet only needs to connect to the router LAN port or wireless network, and can access the Internet without any settings.

Installation and Setup Method:

1. Connect to the wireless router through a computer or mobile phone, open the browser and enter the wireless router login address (different brands of routers have different login addresses, management usernames and management passwords, you can refer to the wireless router manual, the new version of the wireless router does not manage users and passwords, and you need to set it for the first time);

2. Enter the wireless router management interface, and modify the LAN port address of the wireless router to avoid conflicts with the LAN address of the fiber modem (the router will be prompted to restart after the modification is saved);

3. Connect the network cable from the LAN port of the fiber modem to the WAN port of the router, connect the LAN port of the wireless router to the computer, and the computer will automatically obtain the IP address.

4. Log in to the wireless router again, click "Internet Settings", select PPPoE dial-up mode, enter the Internet account and password, and save;

5. Click "Wireless Settings", set the wireless name and wireless password, save it, and restart the wireless router.

The steps to connect an optical modem to a route are as follows:

2. Reset the router and press the reset button on the router with a pin or other items.

4. Click "Setup Wizard" in the left function menu> select "Dynamic IP" and click Next;

5. Set the SSID and wireless password and click Next;

6. Click "Done" and the router will restart automatically.

Hello, you can pull the network cable from the lan1 port of the telecom optical modem (some cats write the network port one) plug in the WAN port of the router, and then use the mobile phone or computer to enter the setting page of the router for broadband dialing, generally you can access the Internet by dialing directly, if you can't access the Internet, you can use the dynamic IP of the router to access the Internet. To add: the cat's lan2 or network port 2 should not be plugged into a desktop computer or TV or the like, this kind of network cable can be used to access the Internet router, because a broadband can only be dialed once. Thank you!

The wireless functions of telecom optical modems are generally limited and require professionals to set up.

Users can buy a wireless router, how to set up:

1.Do not connect the wireless router to the optical modem first, and connect the computer to the LAN port of the wireless router first.

2.Open the browser on the computer and enter the routing management interface, and the default username and password is admin;

3.Run the setup wizard, select the dynamic IP Internet mode, save it, then set the wireless password, and select the WPA2 encryption mode;

4.In the LAN port settings under Network Parameters, set the LAN port address to save and restart the router to take effect.

Note that when you enter the management interface of the wireless router in the future, you will need to enter it).

5.Connect the cat to the WAN port of the router, and then the computer can directly access the Internet without manual dialing;

6.If you can't connect to the Internet after following the above steps, open the browser and enter it to enter the route management interface, and turn off DHCP.

Dial 10000 and press 0 to enter the artificial station.