The fully automatic washing machine is filled with water as soon as it is dehydrated, and it cannot

In fact, it may be your little clothes, such as socks; Underwear and the like are sandwiched between the outer cylinder and the inner cylinder, and I have encountered this kind of problem when repairing, which is a headache! Because the inner cylinder is very troublesome to disassemble! You can remove a few fixing screws around the top of the inner cylinder, shine a flashlight on it, and see if there are any foreign objects in the inner cylinder, so that the inner cylinder cannot operate normally!

Find a piece of wire to pick out the foreign object, if you can't pick it out, you have to unload the inner cylinder. (Look carefully, because the things that can go in are relatively small and not easy to see) and then you observe whether the inner cylinder is in the middle of the washing machine! That is to say, it must be level!

Otherwise, the above phenomenon will occur; Also, the pull rod mentioned by the maintenance staff is the main support rod for hanging the inner cylinder of the washing machine, the automatic washing machine is suspended, there are a total of four pull rods, each pull rod has a very thick spring inside, keep it level, if there is a pull rod inside the spring is broken, it will lose balance, it will frequently start the protection device, let the washing machine enter the water to carry out the secondary balance! If it is a problem with the tie rods, all four tie rods must be replaced, otherwise it will not last long, and the same problem will happen again! Don't bother yourself to save money!

This is because the barrel of a fully automatic washing machine is hung on the shell with four tie rods, and if one of the levers is broken, it will cause an imbalance and cannot be dehydrated, so it must be that the levers are broken. I hope to add points, mobile phone typing is very hard.

Why don't you consider the washing and extracting machine of Foshan Jieji Royal brand

The washing machine is washed and normal, indicating that the motor and drainage circuit are working normally, and the reason for the failure may be that there is a problem with the dehydration system.

Solution: 1. Check whether the clutch lever on the electromagnet lever that controls the work of the deceleration clutch is loose, if it is loose, it will be unable to pull the clutch brake lever, and the clutch cannot be converted from the washing state to the dehydrated state.

2. When inspecting, push the electromagnet armature with your hand. Once the armature is fully pushed into the chute, check that the pawl is completely detached from the ratchet. Otherwise, the clutch is still in a cleaned state. At this point, simply screw in the adjustment screws so that the pawl is completely separated from the ratchet.

3. Check whether the fastening nut of the large pulley is loose. If it is loose, there will be a gap between the clutch sleeve and the outer shaft. During dehydration, the spring of the square wire clutch is partially embedded in the gap, which affects the transmission of the moment, resulting in abnormal dehydration.

4. Check the square wire clutch spring. The dewatering operation relies on the square wire clutch spring to transmit torque. If the square wire clutch spring is bad, it cannot be dehydrated.

Practice has proved that the abnormal dehydration caused by the problem of square wire clutch spring is more common. The inspection results are: the spring of the square wire clutch is broken and damaged, the test is carried out after replacing the new parts, the washing machine is dehydrated normally, and the fault is solved.

Summary. Reason:

1.See if the washing machine has a drain-free function, it has been turned on, and after opening, it will not only not dehydrate, but also not drain.

2.Is it wool washing, wool washing, is generally set to not dehydrate, so as not to cause wool shrinkage. Yes, this is a normal phenomenon, take it out and hang it in a mesh bag, and it will be good to dehydrate naturally.

3.The washing machine water level switch is faulty, the lowest water level has no signal, and of course it is not dehydrated. In this case, the machine will report the fault, please wait to see the fault code.

A fully automatic washing machine can be dehydrated for a while, and it can't be dehydrated for a while, what's going on.

Reasons:1See if the washing machine has a drain-free function, it has been turned on, and after opening, it will not only not dehydrate, but also not drain.

2.Is it wool washing, wool washing, is generally set to not dehydrate, so as not to cause wool shrinkage socks water. Yes, this is a normal phenomenon, take it out and hang it in a mesh bag, and it will be good to dehydrate naturally.

3.The water level switch of the washing machine is faulty, and the lowest water level does not believe in the rising trace, of course, it is not dehydrated. In this case, the machine will report the fault, please wait to see the fault code.

1. The washing machine did not move without dehydration at all, because the safety switch on the upper cover was in poor contact. Solution: Disassemble the upper cover assembly, adjust the safety switch or polish the switch contact to improve.

2. Remove the leather belt, if it is still one-way rotation when washing, it is broken to roll the Yulu computer board. Solution: Common clutch fork fork is not in place or the hook of the torsion spring is broken, adjust the position of the pawl or disassemble and replace the torsion spring.

1.Fully automatic washing machine can be washed without dehydration:

1) The washing machine panel door is not closed well or the switch of the top cover is damaged, it may also be that the switch is in poor contact, the washing machine is not allowed to open the top cover because it is a high-speed action when dehydrating, so there is a linkage switch on the top cover, and the cover circuit will be automatically disconnected as soon as the cover circuit is opened. If it is damaged and dehydrated, it will not move!

2) The drainage system of the washing machine is blocked or the drain valve is broken, the washing liquid in the water cylinder cannot be discharged, or there is too much foam in the water cylinder, the washing liquid in the cylinder is difficult to drain for a while, the water level switch cannot be reset, and the washing machine cannot enter the dehydration program.

3) The drain valve does not open the clutch conversion, and the washing and dewatering of the automatic washing machine is completed by the gear at the bottom of the solenoid valve conversion, and the damage of the solenoid valve will also make the dehydration unable to operate normally!

4) Poor motor performance and capacitance problems, resulting in insufficient output power, can be solved by replacing the capacitor.

Summary. 1. The lid of the washing machine is not properly covered.

When the lid of the washing machine is not covered, it will cause the situation of non-dehydration, just cover the lid of the washing machine, and do not open the lid of the washing machine during the dehydration process of the washing machine.

2. Too much clothing.

Too many clothesIn the process of washing, the washing machine will automatically adjust to a low speed to cause poor dehydration effect, reduce the number of clothes before washing clothes, and don't stuff too much at once.

3. The clutch is damaged.

Damage to the clutch will cause the clutch to fail to clutch to the dehydrated state in the cleaning state, and the clutch will need to be replaced.

4. The water level switch is damaged.

When the water level switch is reset, the washing machine will enter the dehydration procedure normally, if the water level switch is damaged, the washing machine will not be dehydrated, and you need to contact the after-sales point for maintenance.

5. The drainage system of the washing machine is blocked.

When the drainage system of the washing machine is blocked, the washing liquid in the washing machine cannot be discharged, and the washing machine cannot enter the dehydration program, so the foreign matter in the drain valve can be cleaned.

The fully automatic washing machine can wash clothes normally, but it cannot be dehydrated.

1. When the washing machine cover is not covered, it will cause no dehydration, just cover the washing machine cover, and do not open the washing machine cover during the dehydration process of the washing machine. 2. Too much laundry and too much laundry In the process of washing, the washing machine will automatically adjust to a low speed to cause poor dehydration effect, reduce the number of clothes before washing clothes, and don't stuff too much at once. 3. Clutch damageClutch damage will cause the clutch to be unable to clutch to the dehydrated state in the cleaning state, and the clutch needs to be replaced when this belt is instructed.

4. The water level switch is damaged, and the washing machine will enter the dehydration program normally when the water level switch is reset, if the water level switch is damaged, the washing machine will not be dehydrated, and it is necessary to contact the after-sales point for maintenance. 5. When the washing machine drainage system is blocked, the washing machine is blocked, and the pure water system is blocked, which will cause the washing liquid in the washing machine to not be discharged, and the washing machine can not enter the dehydration process, so the foreign matter in the drainage valve can be cleaned. The above is to introduce the automatic washing machine can not be dehydrated, I hope it will help you.

The dehydration motor of the automatic washing machine rotates, and the inner barrel does not rotate.

Please wait. In this case, there may be a problem with the starter capacitor. Washing machine is an indispensable household appliance in modern life, and people can't do without it every day.

The washing machine is a very frequently used household appliance, and some failures are also relatively common, among which the problem of dehydration is also one of the problems that are often seen.

It is recommended to find a professional to repair it.