No one came out last time, notebook PPPOE Internet problem 20

Does your PPPoE come with XP or install other dialing software, try another dialing software!!

Dialer software to search inside!!

First of all, it is necessary to ensure that the plugging position of each connector is correct, and then deal with it as follows:

1. This is because the router does not recognize the MAC address correctly, find the location as shown below in the router settings page, and then.

Click "MAC Address Clone", and finally save and restart the router. Exit the router settings page.

2. Then open the "Control Panel" of the computer in turn"IE option"Connect, select Never dial connection for broadband dial-up method, and then save it.

Note: 1. The broadband connection mode in the router settings page must be selected as "automatic connection", not "on-demand connection", otherwise the broadband will often be disconnected.

2. The IP added by the "default gateway" in the local connection settings must be consistent with the IP input in the IE address bar when logging in to the router interface, for example, the "default gateway" in the local connection settings must also be added. If you don't know how to set up a local connection, you can choose to get an IP address automatically.

Is it because your routing settings are not set up properly, and your computer is directly plugged into the network cable without going through the route, do you need to dial up?

In connection to the broadband is a pppoe error, what is the matter.

There are no more than 3 reasons for the connection error: 1. There is a problem with your computer software, which can be reinstalled; 2 is that the cat has a problem, you can restart it to see, 3 is the service provider that has a problem, including the line, password, account, and the reason for temporary adjustment, you can ** to them. PPPoE enables computers on a network to connect to remote access devices through a simple bridging access device.

Under this model, each user host leverages its own PPP stack, and the user uses a familiar interface. Access control, billing, service types, etc., can be done on a per-user basis, not on a per-site basis. In order to provide a point-to-point connection on an Ethernet cluster, each PPP session must know the Ethernet address of the remote communication party and establish a unique session identifier.

PPPoE includes a (Ethernet address) discovery protocol to provide this functionality.

1) If it is a problem with the broadband itself, first directly connect the broadband network cable to test, if it is a broadband problem, contact the broadband customer service to solve it.

2) If it's a problem with the router, if it can be used originally, it won't be bent for the time being, my own practice is to disconnect the power supply of the router and plug it in, and I'll take a look. In there is a factory reset, from the new strict according to the manual settings can be used, I don't understand, it is not recommended to set it at will (this is under the premise of the correct physical connection, sometimes the router is slow or failed to find the IP address, not that the router is broken).

If it can't be solved all the time, it is recommended to call the customer service of the router, they have **** guidance, I encounter a problem that I can't solve by myself, it is very useful to consult the advice they gave, and they will give the correct advice for your settings or operations.

3) If you turn off the wireless switch, it's just that, if it's a wireless connection with software, it's normal for the software to be hard to use and often have problems after rolling up, there is no better way, use a router. In addition, it is caused by the network card driver is not or is not suitable, and whether there is a problem with the network cable interface or network cable.

4) If it is caused by a system problem, it is recommended to restore the system or reinstall it.

Use the system that comes with the system restore method:

System Restore that comes with the system: "Start" "Programs" "Accessories" "System Tools" "System Restore", click "Restore my computer to a large size earlier", press Next, you will see that the date page has a dark date, that is the restore point, after you select, click Next to restore (win7810 restore the system, right-click on the computer to select attributes, on the right side to select system protection, system restore, follow the steps to do it, if there is restoration software, you can also use the software to restore the system).

5) If you have any questions, please ask me.

Can I access the Internet without routing? If you don't use the route vertically and can't get on the network, then you don't have to say anything, if the stand-alone machine can access the Internet, check the configuration of the router, connect to see if you can ping the router, if you pass, then ping the external network, if you can't ping, routing problems! Check it out step by step and see.

Check your old or network connection Check your local connection in the Internet protocol to automatically get slippery with Huai to get the IP if it doesn't work, check the hardware such as the network card.