Why is the wireless router mobile phone not even connected to the Internet, and the computer cannot

Problem 1: All WAN port parameters are 0 and the connection is always in progress, but the connection cannot be successfully (log in to the management interface of the router and click Running Status >> view the WAN port status);

Solution: 1. Check the line, if the line is connected correctly, but the WAN port indicator is not on, please check whether the WAN port wiring is in poor contact, etc., and try to replace the network cable connected to the WAN port;

2. Confirm that the password is entered correctly, click Running Status >> WAN port status on the management interface of the router, if the WAN port does not get the IP address, the page will have a prompt for the reason of dialing failure, modify it according to the prompt;

3. The broadband service provider binds the MAC address, connects the computer that was connected to the broadband Internet access separately with the LAN port of the router (here it must be connected by wire), and logs in to the management interface of the router. Select Network Parameters >> MAC address clone, click Clone MAC address. When the MAC address is the same as the MAC address of the current management PC, click Save and Restart the Router.

Solution: 1. The computer needs to be set to automatically obtain the IP address - if the computer has automatically obtained the IP address, but the IP address obtained, please disable the local connection or wireless connection corresponding to the computer and then enable it.

2. Check the router's Internet access control - the router's parental control and Internet control (some routers are set by firewalls) function can restrict the Internet access permission of the intranet computer, please set the function according to the actual needs, if it is not necessary, you can not enable the function. Here's how to set it up:

1) Turn off Parental Controls - Log in to the router management interface, click the Parental Controls settings page, select Disable and Save.

2) Turn off Internet Access Control - In Security Settings >> Internet Control, make sure that Turn on Internet Control is unchecked, and click Save.

3. Check the browser settings - please check the browser settings, the check method is as follows: Disable dial-up connection: Open IE browser, click Tools >> Internet Options, select Connect>> never dial-up connection; Disable Network**:

Click Tools >> Internet Options, select Connect >> LAN settings, make sure none of the three options are checked, and click OK.

After setting up, try to open the browser to surf the Internet;

4. Change the browser or computer - try again after changing the browser (using Firefox, Google Chrome or other browsers), if you still can't access the Internet, try to change the computer for comparison and testing;

What brand of wireless router? It could be that you set up the problem!

What you said is not right, your method is only for regular failures, and people with a little network knowledge will. Can only solve some conventional problems, I have gone through countless countless troubleshooting experiments, came to a conclusion, there are many routers, there will be a strange fault phenomenon, computers (wired equipment) can access the Internet, mobile phones (wireless devices) can not be connected to the Internet even if connected to wifi, I don't know how to explain this problem, although I can't explain, but there is the only way to solve the problem, that is, "restore router factory settings", "restore router factory settings", " Restore the router to factory settings", important things said three times. After restoration, you can set the corresponding Internet access method.

One is that the wireless route is not linked correctly, the wireless route is not linked to the network, the router is used as a switch, and the computer still dials up the Internet by itself.

The second is that the router's wireless network is not turned on.

The proper steps to install the router are as follows:

1. The network cable is connected to the WAN port of the router, and the computer is connected to the LAN port of the router.

2. Open the computer browser, enter the IP address of the router, and enter the settings interface of the router. Generally, you can check the manual of the router or the router will be marked with the routing IP on the back

3. Set the WAN port parameters. Generally, dial-up Internet access, select PPPOE mode, enter the account number and password, and the connection mode is automatic connection.

If you use the Internet in static IP mode or from another router, you need to select a static IP address, enter the IP address, gateway mask, DNS, etc. (These parameters need to be obtained in advance, you can connect the network cable directly to the computer, and then check the status of the local link of the network, you can see the IP and other data).

4. Set up a wireless network. Set the SSID number, encryption method, and password.

It may be due to the following conditions:

1) There is a problem with the broadband that provides wifi hotspots, you can try to connect the computer alone;

2) If the broadband is normal, it may be caused by the wifi setting problem, you can reset the wireless network to try to connect;

3) Caused by mobile phone problems, you can change the phone for testing.

Two possibilities.

First, the wireless router is not set up. You do this:

Plug in the wireless router, reset the wireless router (factory reset), don't answer the cat first, connect the computer to any LAN port of the wireless router, enter the settings page, and set it according to the PPPoE (ADSL virtual dialing) method. Then set the SSID, encryption method, and password.

After setting up, connect the network cable from the cat to the WAN port of the wireless router.

Second, the wireless router is set up, but the mobile phone fails to obtain the IP address correctly. You can go to the settings page of the wireless router and enable the DHCP service of the wireless router.

The wireless router needs to set a static IP for the mobile phone to connect, you find the static IP setting in the settings and then refer to the IP settings to set it again.

It is possible that the MAC restriction is enabled for the route, and the MAC of the phone is not saved to the route.

The phone may not match the IP address of the router.