The water heater will not be hot every time you take a bath. What is the problem burning liquefied

Generally speaking, the water heater can heat at the beginning, which proves that the battery is good, otherwise it can't be hit, and there is no need to use the battery after it is turned on, so it must not be a problem with the battery.

The water heater is hot at the beginning, that is to say, there is no problem at the beginning, and the reason why it is not hot is not necessarily the problem of the water heater, because the water heater itself is not generally impossible to have this kind of problem, either it is not hot, or it is good, and there will be no problem of being hot for a while and not being hot for a while.

There are three reasons why it is not hot after the meeting, one is that your gas is insufficient, and the gas can't keep up when it burns halfway, don't think that the gas cylinder is still very heavy and feel that there is gas, now the gas has a lot of slag, and generally it can't be burned when there are two or three kilograms in the end, you can change a good bottle to try, and the replaced one can be put on the gas stove.

The second is that the weather is too cold, because the gas exists in a liquid state in the bottle, and it is also afraid of cold and will freeze. If the indoor temperature is too low, the gas will not evaporate into a gaseous state. Resulting in a situation where gas is not enough.

The last one is that the water pressure is not enough, the general gas water heater relies on the water pressure to push the gas, if the water pressure is not enough, the gas cannot be turned on, and it is naturally not hot, but if you have a lot of water, it is the first two possibilities.

The solution is to pour some hot water on the gas cylinder

1 may be that there is not enough oxygen, open a window to ventilate.

2If it is a gas tank, it may be that the gas volume is insufficient, so shake it vigorously, or put the gas tank in a basin with hot water.

3. The battery is not enough to catch fire.

4. The water heater is broken.

The capacity of the water heater is slightly smaller, and when taking a bath, due to the continuous replenishment of cold water, the heat burned is not enough to replenish the heat of the newly added cold water, so that the temperature of the hot water keeps dropping. There is also the possibility that limescale has formed inside the water heater. Prevents the introduction of some heat.

It is recommended to reduce water consumption. Remove limescale.

Our family was like this, and then we called someone to fix it and replaced it with a rubber ring inside. It costs 20 bucks, and then it's fine.

The time in the west is too long, and the hot water is used up, so naturally it is not hot.

Summary. Hello. 1. The pipeline is blocked, and there are debris blocked in the pipe, which directly affects the water heating of the water heater.

2. The pressure of the gas water heater is relatively low.

3. The mode is not set well.

Why is there no hot water when the gas water heater is washed?

Hello. 1. The pipeline is blocked, and there are debris blocked in the pipeline, which directly affects the water heating of the mega oak to the hot water positive wheel. 2. The pressure of the gas water heater is relatively low. 3. The mode is not set well.

The time on your mode is 30 minutes, isn't it?

You want to put that mode on top of the settings. Once you've set it up, you won't have to do that.

Summary. Dear, I'm glad to answer for you: The gas water heater bath water is not hot, what's going on?

Kiss the gas water heater at home The hot water is not hot solution: Check the pipes at home, you can first turn off the 2 water valves of the natural gas machine, and then go to the faucet to see if there is any water coming out of the hot water faucet. It is usually connected to another water heater, as well as a solar, bathtub mixing valve.

Because it is impossible for all hot gas water heaters to be used at the same time, if they are used at the same time, the cold water that is not heated by the other machine will be stringed into the hot water pipe, so it is necessary to turn off the water valve of another machine that is not used, so that the water will not be stringed, and the water will be added to the machine used, and the water temperature will be there.

The gas water heater is not hot when you take a bath, so what's going on.

Dear, I'm glad to answer for you: What is going on when the gas water heater bath water is not hot Answer: The hot water of the gas water heater at home is not hot Solution:

Check the pipes at home, you can first turn off the 2 water valves of the natural gas machine, and then go to the faucet to see if there is any water coming out. It is usually connected to another water heater, as well as a solar, bathtub mixing valve. Because it is impossible for all hot gas water heaters to be used at the same time, if they are used at the same time, the cold water that is not heated by the other machine will be stringed into the hot water pipe, so it is necessary to turn off the water valve of another machine that is not used, so that the water will not be stringed, and the water will be added to the machine used, and the water temperature will be there.

I'm new, and when I take a shower, it's hot and cold.

Pro, 1, the water pressure is not enough to take a bath in winter, many people are used to turning on the hot water switch to the maximum, but once the water feels hot, someone turns the faucet violently, and the newly added cold water increases the water resistance, and when the resistance is large enough, it will cause the gas water heater to go out. There will be hot and cold situations. Workaround:

In this situation where the water pressure is not enough, one way is to add a booster pump, and if you don't want to install it, you can choose to use the water heater when each person uses water. If the water is supplied by the water tank on the roof, the pressure is only related to the height difference between your home and the water tank, and the water pressure is not enough, you can consider installing a water pump. The second method is to find the property to solve the water pressure problem, causing the water heater water temperature to not be hot enough or hot for a while and cold for a while, if the water volume of the shower is not significantly reduced, it may not be a problem of water pressure; It can solve the problem of hot and cold gas water heaters.

It is possible that the water is not hot due to limescale in the water heater.

1. The gas water heater is water-controlled, and there is a minimum water flow requirement, which is not met, and the water heater cannot release gas and turn on the igniter, and cannot be used.

2. It is recommended to check the water output of the hot water faucet, if it is small, it may be a problem caused by insufficient water flow.

3. The cold water is normal, the hot water output is small, it is necessary to consider why the original hot water is large, and now the hot water is small, the reason is that the scale deposit is more original, the problem of blocking the pipeline, the water flow does not meet the conditions, and the water heater cannot be ignited.

4. There are many reasons why gas water heaters are not good for ignition, and any component damage of water, gas and electricity will cause the water heater to fail to ignite.

5. But now the quality of water heater components is generally improved, not so easy to break, in fact, many times the reason why the fire can not be ignited is because of the scaling of the waterway caused by the blockage of the hot water pipeline, resulting in a large back pressure of the waterway flow, to a certain extent, the water heater water-gas linkage device will think that the hot water faucet has been closed and close the gas channel, no gas, of course, it can not catch fire, if the hot water faucet is fully opened in the near future, the hot water pressure is smaller, and the possibility is greater. Now that the igniter is working properly, it is even more certain. It is recommended to clean and descale immediately.

YesClick on the link below, or call the official **, make an appointment with a professional water heater cleaning master in the same city to come to deal with it for you.

That's because the hot water in the water heater is not enough, and secondly, because the water is circulating all the time, so this happens.

When the water heater is heated to increase the internal pressure of the water heater, if the pressure exceeds the safety pressure, it will drip water from the safety hole to relieve the pressure, but if there is a problem with the discharge valve, the water cannot be entered, so the hot water will not be released.

Due to the lack of pressure difference, the hot water will be trapped in the water heater, and if this is the case, the hot water will not be released. At this time, the treatment method is to remove the high-pressure hose between the hot water pipe and the cold water pipe, and at the same time, add a plug to make the pressure difference between the cold and hot water pipes, and the pressure difference will naturally release the hot water.

It is likely that the volume of the water heater is relatively small, or it may be because the temperature is relatively low, or the water preheated in advance has been used up, or it may be because the dashboard is out of order.

It is very likely that your water heater capacity is too small, so it will run out of hot water after using it for a while, and this situation is also very common.

Reasons why hot water cannot be produced after the water heater is cleaned:

1.During cleaning, residue enters the shower, causing the shower to be clogged and unable to drain water.

2.During cleaning, the large scale residue inside is blocked at the interface of the hot water pipe, because there is a sealing gasket at the interface, and if you do not pay attention to it during installation, it will cause the gasket to shift and deform and make the pipeline narrow, and the scale residue is blocked, so the hot water cannot be discharged.

3.The inlet valve did not open.

4.The tank was not filled with water, so no hot water was discharged.

Solutions to the above problems:

1.Thoroughly clean the inside of the shower and hose to eliminate limescale residue and clogging. If the blockage is severe, replace the shower and hose;

2.Use a wrench to remove the hot water pipe interface, clean the residue at the interface part, and ensure that the pipeline is unobstructed;

3.Open the inlet valve to ensure that the water in the tank is sufficient**;

4.Turn on the shower and pour water into the tank, and when the water from the shower flows out slowly, the water in the tank is full.

Note: When disassembling the hot water pipe, the power must be cut off first, and then the water inlet valve must be closed to drain the internal water before the hot water pipe can be disassembled, otherwise it is easy to burn and there are other potential safety hazards.

For N card, click Manage 3D Settings in the graphics card management settings, and then in the global settings on the right, you will prefer.

Graphics Processing Unit.

The option below is changed to a high-performance NVIDIA processor, and when you're done, remember to click Save at the bottom.

If you want a card, you can add the i program that needs to be applied to the independent display card settings, and select high performance after adding.

This is the setting of win7.

Hello! Or check the water heater, whether it is installed in reverse, whether the valve is unblocked, and whether the cold water can pass through.

When in doubt, please ask.

After the water heater is cleaned, it will not be heated after it is filled with water and energized, and E2 will be reported as a solid barrier.