The router cannot be debugged, please ask the router debugging method

There are 5 ports on a general wireless router, as shown in the figure below:

The following picture is the wiring method of the wireless router, which is very simple and can be understood at a glance:

I think you can see it!

Here's how to set up your router on your computer:

1.Open the browser and enter the IP address of the router in the address bar (the equipment of different manufacturers may be slightly different, here is the wireless router I am using as an example), type and enter the user name and password in the pop-up form (the equipment of different manufacturers may be slightly different, here take the admin of the wireless router I am using as an example, the username and password are admin):

2.After that, go to the router's configuration page:

3.After entering the login interface, the next step is to configure the password for broadband dial-up Internet access; Enter the setup wizard;

4.Then follow the prompts to configure it step by step:

5.Type in your ADSL broadband internet and password:

6.Next, enable wireless, and enter your wireless router WLAN password, whatever you want, but it must have 8 digits.

In this way, the wireless router is configured, and when the router dial-up is successful, you can access the Internet on multiple devices at the same time.

It's still relatively clear, let's try it!

1. Use the computer to connect the Huawei cat through wired to see if it can access the Internet, if you can't access the Internet, and the network card of your computer is good, it may be that the Huawei cat is broken;

2. If step 1 can access the Internet, check whether the default IP of the LAN port of the Huawei cat is the same as the default IP of the TP Link router, generally yes or, if the IP of the Huawei cat and the TP Link router is the same, modify the IP of one of the devices, it is recommended to modify the router IP of the TP link.

3. If there is no problem in step 1 and step 2, then see if the router wireless switch of TP Link is turned on, if not, turn it on;

4. If there are no problems with the above, it is recommended to find someone to solve it directly.

1. Router> Under the router > prompt, the router is in the user command state, at this time, the user can see the connection status of the router and access other networks and hosts, but can not see and change the settings of the router. Enter at this point? and press Enter to see the commands that can be used in this state.

iOS allows you to see commands available in a certain state at any time in this way).

2. After the router enters the privileged command state, it can not only execute all user commands, but also see and change the settings of the router. At this point, you can set the name and password of the router.

3. Router(config) Type configure terminal in the router prompt, and the prompt router(config) appears, the router is in the global setting state, and the global parameters of the router can be set.

4、router(config-if)#; router(config-line)#; router(config-router)#;…The router is in the local setting state, and you can set the parameters of a certain part of the router.

5. The router is in the rxboot state, press ctrl-break within 60 seconds after booting to enter this state, at this time, the router can not complete the normal function, and can only perform software upgrade and manual boot. In this state, password recovery is possible.

Router, generally with RJ45 crystal head connection line, and the general WAN port will be connected to the network model, such as cats, or router WAN port set static IP connection, to other routers or switches, and the router is generally divided into several ports, that is, several sockets, connected to the computer on the LIN port, after the normal IP address appears at the local connection of the computer, check what the default gateway of the IP address is, and enter how much in the IE address bar of the computer, And the router also has a written dial-up address and password behind it, and yours generally if it is today's cat Internet access to the Internet on the Internet choose pppoe dial-up Internet, enter the username and password given to you by the network company to save, check whether the router status is connected, the connection means OK, not connected Look at your link error, it is best to restart the router after the router is set up.

The installation and setup of the router is as follows:

1.First connect the line, you can refer to the figure below.

3.Once you've logged in to your backend, select Quick Settings and click Next4Choose the way to access the Internet, usually ADSL users choose the first PPPoE, if you use other network service providers, then choose the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

5.Enter the account and password applied for from the network service provider, and go directly to the next step after entering.

6.Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

7.After entering it correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

After the power is turned on, connect the wireless router to the computer, open the browser and enter in the address bar: to enter the settings interface of the wireless router. According to the setup wizard step by step, select the Internet access method, and restart the wireless router after the setup is completed.

Next, go to the wireless settings and set the SSID name

Normal is input set, no.

There are a few questions to confirm with you first:

1. Are you sure you have a network on your external network?

2. If there is a network, you make sure that your router settings are correct and whether the account password of its network broadband is correct; (You're on the right line).

3. Whether the network segment of your route is correct, yes or wait, confirm that it is correct to see if you can access it, if you can't open it, you can set your computer to a static IP address with the gateway, and then try to access;