Find a complete tutorial for Wemeng router debugging

The setup method of the WayOS router is as follows: 1. Turn on the power supply of the router, then plug the incoming cable of the broadband network into the WAN port of the router (usually the blue port), and then plug the network cable connected to the computer network card into a LAN port at will. 2. Enter the IP address you see on the router in your browser

Then enter the login interface and enter the account and password of the router, which is usually admin. 3. After confirmation, enter the setting interface and click the setup wizard. (Generally, it pops up automatically) 4. Click Next, enter the Internet mode settings, you can see that there are three Internet access options, if your home is dialing, then use PPPoE.

Dynamic IP can be used by plugging the computer directly into the network, and there is a DHCP server on the upper layer. The static IP is generally a private line or something, or it may be the cell bandwidth, etc., and there is no DHCP server in the upper layer, so PPPoE is selected because of dial-up. 5. If you choose PPPOE dial-up Internet access, you need to fill in the Internet account and password, if you forget it, call customer service ** to contact the corresponding operator and ask for the account and password.

6. Then click Next to enter the wireless settings, you can see the channel, mode, security options, SSID, etc., wireless security options to choose WPA-PSK WPA2-PSK, so safe, so as not to let people crack and rub the network. 7. After the setting is completed, the router will automatically restart, and then the connection is ready to use.

It should contain a lot of things.

The steps are as follows:

2. Open the "Authentication Management" >>PPPoE Settings" parameter setting.

3. Open the "Authentication Management" >>"Group settings"。

4. Set the time IP address of the group

The significance of the IP address and subnet mask here: If this group is selected when dialing in PPPoE, the IP addresses that are automatically obtained after the account is dialed are obtained sequentially. Equivalent to PPPOE multi-network segment (note:

The CIDR block here is only valid for PPPoE users, and the IP address assignment does not take effect when the web account is used, and the IP address is used according to the IP obtained over the intranet).

5. Set a speed limit.

The speed limit is controlled according to the time, and there are 3 time periods set here, (the time of writing is Friday) the time is set to 17:52 on Friday and 100kbytes for each uplink, 17:53 for week 5 and 150kbyte for uplink, and 17:00 on Friday

54 minutes for 200kbytes of uplink.

6. When setting the PPPoE account and password, you can select the user group, and the user group here is the group setting just set.

7. Use a computer for PPPOE dialing.

8. After dialing, you can view the obtained IP address as .

9. Now you can see the effect, the maximum data can only reach the limit when the time is 17:53: 54 is up to 200k, and 18:09 is up to 200k.

After the router is restarted, there is no speed limit at that time, and the speed is automatically limited according to the set conditions when the trigger time condition is reached.

10. Web authentication speed limit.

Web authentication is the same as PPPoE group settings, but the assigned IP address is different. The IP address of the web is allocated using the CIDR block of the intranet, but the rate limit in the group settings takes effect.

The two networks of the Weimeng router with multiple WLAN ports will not be opened after a while, and the ping inside the router is all connected, and it will be fine if you connect to one network.

Hello! The method of setting up the VM router is as follows:

1. Check whether the power is on and whether the wireless router is running normally.

2. After checking that it is correct, open the browser and enter: press Enter to enter, at this time a dialog box pops up, you need to enter the account name and password, this does not have to worry, there will be in the back of the router, you can log in if you find it, in general: account name:

admin password: admin

3. After entering the password behind the router, you can log in to the settings page of the router.

4. Click on the setup wizard on the page, and a box will appear that will lead you to set up the router, and follow its requirements step by step.

5. Click Next to enter the account password settings, this account password is your current network access account password, if you don't know, you can consult your operator.

6. After setting the account and password for surfing the Internet, the function of wireless Internet access is set, set your wifi name and wifi password, it is recommended that the password is not too simple, it is easy to be cracked, and the encryption method can be recommended by the system. 7. Click Done, and your router setup has been successful.

Intelligent equipment, intelligent functions.

The front-end adopts smart WiFi gateway devices with different capacities according to the environment, realizing the function of multi-WAN smart routers, and integrating centralized network control and smart WiFi cloud platform. It realizes powerful functions such as multi-line intelligent superposition of external networks, user online behavior management, intelligent network traffic rate limiting, and efficient intelligent defense of ARP.

Multi-function in one, multi-device centralized unity.

The gateway integrates AC server, router and AC controller two-in-one device, which can centrally and effectively control distributed wireless devices, including data delivery, designated relay, remote upgrade, etc., and can centrally configure the parameters of each distributed device, including wireless channel, device login user name, VLAN division, etc., to truly realize network management background control and multi-layer distribution.

Strong wireless signal, Chinese name broadcasting.

Strong signal wireless AP, perfectly compatible with WayOS equipment terminals, standard hotel rooms cover about 8 12 (ceiling wireless AP), and support Chinese SSID broadcast form, can make different smart WiFi terminals effectively compatible, so that business promotion is more impactful.

Hello! The specific setup method of the VEM FBM220 wireless router is as follows:

1.Connect the power supply of the router, and then plug one end of a network cable into the network port of the computer, and the other end into the LAN port of the router.

2.Open the browser of the computer, enter the IP of the router in the address bar (the IP of most products is, click the enter key to enter the settings page of the router, the username is admin, the password is blank, click to log in, and enter the settings home page of the router.

3.Once you're logged in to the home page, select Manual settings. Then select Manual Internet Settings, and Home Dial-up users select the PPPoE connection type.

In the username and user, enter the username and password given by the ISP provider (Netcom, Great Wall, Telecom, Tietong, Cable, etc.) correctly. The connection method is always (or automatic.) Model, version may be different) mtu value is 1492.

The save is done.

4.Wireless routers also have a wireless encryption to ensure the user's wireless security. Select the wireless settings on the main page of the router's settings, select an encryption method in the security mode, any one of WEP, WPA, or WPA2, and then enter 8 or more Chinese characters or numbers as the wireless password in the security key, and the router settings will be completed after saving the settings.

5 After the setting is completed, the router will automatically restart, and the external network cable can be connected to the WAN port of the router to use.

Here's how to set up your wireless router:

1. The broadband bus (the network cable from the cat) connects to the WAN port of the router.

2. Connect one end of the network cable to any LAN port of the router, and connect the other end to the computer, and start the computer and router equipment;

3. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface.

4. An account and password to log in to the router appear in the settings interface, enter the default account admin5, set up step by step according to the setup wizard, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, you can directly select the first item to automatically select, which is convenient for novice operators, and click next after selection;

6. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

7. Set the wifi password, try to make the alphanumeric combination more complicated and not easy to be rubbed off the network.

8. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

You're a wired router, not a wireless router, and it doesn't have wireless capabilities.

Click on the network configuration to see, there are network parameter settings.

If you want to access the router remotely, then you need to know an external IP address obtained by the Weimeng router.

and remote ports, including login passwords.

The first one sets the PPPOE connection mode (the router connected to the modem), the second one sets the dynamic IP connection mode, and the gateway can be changed so that it is not in the same network segment as the first one. If the first one is, the second one is changed to, and the DHCP can be changed to achievement.

2 VIM 2WAN to 3WAN ??? The routes that cannot be changed are respectively A B routers.

Router A is responsible for connecting to the modem, dialing in to connect to the network, enabling the DHCP service, setting the Router B port to automatically obtain an IP address or a static IP, and enabling the DHCP service.

What are you going to ask. As shown in the picture above, there is no problem with the connection.