The turn signal of the electric car does not light up, and the instrument turn indicator does not li

If the meter indicator light is not on, first check the power supply fuse of the dashboard.

If the circuit breaker. will need to be replaced. Disassemble the dashboard, the lights are generally at the back of the dashboard, replace the lights that are not lit, and generally the individual lights are not lit to indicate that there is no problem with the fuse and wire, the main reasons are as follows

1. The lamp of the dashboard is damaged and needs to be replaced in time;

2. If the power supply line of the dashboard is broken, there will be an open circuit or a short circuit, which will also lead to the car dashboard.

There is no light up;

3. If the power supply fuse of the car dashboard is broken, there will naturally be no power supply, and the dashboard will not light up.

Precautions in the use of the car dashboard:

1. When the indicator light is on, the odometer should be observed immediately, if the cumulative mileage reaches or exceeds l00,000km, the timing toothed belt must be replaced, otherwise the timing toothed belt may break, so that the engine can not work normally.

2. After replacing the new timing toothed belt, it is necessary to open the rubber plug outside the reset switch on the mileage dial, and press the reset switch inside with a small round bar to extinguish the indicator light of the timing toothed belt.

3. After replacing the new timing toothed belt, remove the odometer and adjust all the readings on the odometer to the 0 position.

It may be that the steering switch is broken, or it may be that the 3-in-1 horn is broken.

This one should be taken apart to see if there is a short circuit or an open circuit, and to see if the bulb is good and whether the wire is connected.

1) Check whether there is an open circuit in the lead wire.

In this case, it is important to check whether the common wire, power line and negative wire of the steering circuit have any stove and open circuit phenomenon, and if so, the line should be reconnected.

2) Check if the bulb of the turn signal is damaged.

If the bulb is damaged, replace it with a bulb of the same model.

3) Check whether the DC voltage converter is damaged.

If the DC voltage converter is damaged, the power supply voltage of the lighting and signal system may rise, and the DC voltage converter should be repaired or replaced with a new one.

4) Check whether the turn signal switch is damaged or damaged.

If the switch is damaged, it should be repaired or replaced with a new one.

5) The flasher is malfunctioning, causing the turn signal of the electric vehicle to not light up.

If the flasher fails, it will cause the left and right turn signals of the electric vehicle to be unlit. The solution to this problem is to replace the flasher.

1. Turn on the double flash switch to try.

Come and test the lights on if not.

The source is bright, and the problem lies in the turn signal switch part.

2. If it is not lit, are all the 4 turn signals not lit? If the problem is with the light bulb, it usually does not break at the same time.

If the turn signal is not lit, it may be that the wiring is broken, the iron is broken, the bulb may be loose, or the filament is burned. The car turns its head with a cross before turning its head.

A: The screwdriver twists out the screws on the lampshade counterclockwise and takes out the lampshade.

Press the steering switch and twist the bulb to see if it can be lit, if it doesn't, twist out the bulb to see if the filament is burned. If the filament burns, buy one and replace it with a new one.

The rear turn signal must first twist out the four screws on the red cover of the rear brake light before the cover of the turn signal can be removed.

It could be a wiring problem or a light bulb problem.

Maybe the wiring is broken or the light is broken.

1. First of all, check whether the connection wires between the batteries, the total battery leads, and the battery leads and the controller socket are in good contact.

2 Some electric vehicle dashboards, speed control handles, and all lights are powered by 12V, and this 12 power supply is converted by the total power supply through a 48V (or other level of voltage) to 12V converter (switching power supply module), if the input and output lines of the module are problematic, or the converter is broken, the rear stage can not work, and the vehicle is in a paralyzed state.

So you must pay attention to check here, in general, your fault should be easy to check, and it is relatively easy to check hard fault.

This situation is generally a line failure, first confirm whether the battery is charged, whether the plug on the battery is intact and plugged in, whether there is a problem with the fuse or circuit breaker, if there is no problem, check the electric door lock, etc., can only be checked step by step, to use a multimeter, if you do not have this ability, then it is recommended to go to the repair shop.

It's just that the electricity can't be turned on! The remote control is still not there, if you have a remote control, press it to see if there is any response, there are three situations when the car is out of power, the electric door lock is broken, there is an empty open protection switch under the seat cushion, and the wire connecting the battery is loose or broken.

Measure the voltage of each battery, and what is particularly low is bad.

If the fuse burns out, it should be dealt with at the repair station, because there are extreme faults such as overcurrent and short circuit. However, depending on the display but not displaying the contents, there may be undervoltage or a connection problem between the control circuit and the power part. Focus on checking the position of each plug of the controller, and then measure whether the battery is severely undervoltaged.

There are two possibilities that the turn signal of the electric vehicle does not light up, one is that the filament is burned out and the turn signal needs to be replaced. It is also possible that it is not charged, and it is a problem with the charger. If it is a charger problem, you need to check the wire on the outside of the charger first to see if there is any breakage, and if so, connect it directly.

Then connect the power supply, all the lights are not on, the charger reimbursement wire is broken, and the charger is replaced directly. If the light is on, try a different charger.

Care recommendationsElectric vehicles should be protected from rain, sun, and bad weather.

Strictly prevent the motor battery from entering water and excessive exposure to the scorching sun. Do not overuse the electric vehicle and let the electric vehicle recuperate and allow the battery to naturally recover its chemical properties. It should be avoided as much as possible to ride for too long a distance in a row, resulting in the battery of the electric vehicle.

Deep discharge, if possible, it is possible to replenish the electrical energy halfway. If you don't ride for a long time, you should charge the potato once every half a month.

The electric vehicle dashboard light shows the icon, but the headlights are not on, and the turn signal is not on.

Hello dear, probably.

1. The flasher is faulty, resulting in the turn signal of the electric vehicle not lighting If the flasher fails, it will cause the left and right turn signals of the electric vehicle to be not lit. In this case, the general solution is to replace the flasher. Second, the turn signal switch is faulty, resulting in the electric vehicle turn signal is not lit If the electric vehicle turn signal switch is faulty, it will cause the left turn signal to not light up or the right turn signal not to light up.

For this situation, it is generally necessary to choose to go to a repair shop for repair and replace the new electric vehicle turn signal switch. 3. The bulb is damaged, resulting in the turn signal of the electric vehicle not lighting upIf the bulb of a turn signal of the electric vehicle is damaged, it will also cause the turn signal on one side of the electric vehicle to not light up. For this situation, it is generally possible to replace the bulb with a new one.

Fourth, the line short circuit, resulting in the electric vehicle turn signal is not lit If the electric virtual car has a short circuit, then it will also cause the electric vehicle turn signal not to light up. In this case, you can generally only choose to go to a professional repair shop for inspection and maintenance. In fact, for electric vehicles, don't look at the steering clear light usually used less, in fact, it has a great role, not only can be used to show the direction of electric vehicles, but also can improve the safety of driving.

Therefore, for users, if the turn signal fails, it must be repaired and solved as soon as possible. Hope mine is helpful to you!

Hello, the turn signal of the electric car does not light up, it is recommended to go to a regular repair shop for repair. Possible causes:

1. If the flasher fails, it will cause the left and right turn signals of the electric vehicle to be unlit.

2. If the turn signal switch of the electric vehicle fails, it will cause the left turn signal to not light up or the right turn signal to not light up.

3. If the bulb of a turn signal of the electric vehicle is damaged, it will also cause the turn signal on one side of the electric vehicle to not light up.

Hello, glad to answer for you.

Check if there is an open circuit in the lead-out wire.

In this case, it is important to check whether the common wire, power line and negative wire of the steering circuit are open, and if so, the line should be reconnected.

Check the bulb of your turn signal for damage.

If the bulb is damaged, replace it with a bulb of the same model.

Check the DC voltage converter for damage.

If the DC voltage converter is damaged, the power supply voltage of the lighting and signal system may rise, and all the bulbs will be burned and all the lights will not be lit, and the DC voltage converter should be repaired or replaced with a new one.

1. The turn signal of the electric vehicle is always on and does not flash, first check whether the connection between the flasher and the external circuit meets the specified requirements. The binding post marked with the letter L should be connected to the turn signal, and the binding post marked with the letter B should be connected to the power supply, and the wrong polarity of the capacitive flasher and the electronic flasher is more likely to damage the flasher.

2. Check whether the bulb specifications meet the requirements of the original car. A bulb with too little power will reduce the current, and the resistance wire inside the flasher will not reach the normal temperature and will not work. Capacitive flashers will stop working due to insufficient charging of their internal capacitors.

3. Replace the flasher with the same specification, if the turn signal can flash normally, it means that the fault is in the flasher, and the reason may be due to contact bonding or contact gap is too small. The contacts should be sanded or the contact gap should be increased to restore the flasher to its original state.

4. The power supply voltage should meet the requirements. If the power supply voltage is too low, the turn signal cannot flash, and only when the nominal voltage is reached, the turn signal will flash normally.

5. The steering switch should be in good contact. The input line of the steering switch touches the output line of the left and right turn signals of the steering switch respectively, if the turn signal flashes, it means that the internal contact of the steering switch is poor, and the steering switch should be repaired or replaced.

6. Check whether the bulb filament is burned out. If so, replace the burned-out turn signal bulb.