What is the matter with the oil brake of the Shifeng tricycle suddenly not braking?

The failure to brake the agricultural tricycle may be due to the lack of necessary maintenance of the brake system, too many impurities in the brake master cylinder, poor sealing, and failure of the vacuum booster pumpBrake fluidAir resistance, oil leakage from the brake master cylinder or sub-cylinder, air leakage from the air reservoir or pipeline interface after being heated or several brake fluids are mixed or heated; When it comes to driving safety, it is recommended to ask a professional to overhaul it.

What you need to pay attention to when riding a three-wheeler:

1. There is no limit to the number of drivers, and it is not suitable to drive if you are too young or too old.

2. Be sure to abide by the traffic rules when driving on the road, and do not overtake or rush in crowded sections, roads with many vehicles and crowds, so as to avoid accidents. And when driving on urban roads, you should drive in the slow lane and drive in the fast lane, and if you are found, there will be fines and deductions. Whether you are driving in the countryside or in the city, you must drive on the right side of the road and try to avoid motor vehicles to avoid personal safety accidents.

3. Electric tricycles.

Parking, start attention, after the vehicle stops, turn off the key in time, pull out the key, and pull the handbrake.

If there are children on it or children playing on it, it will accidentally touch the vehicle and walk forward, which is prone to accidents. To start driving, you must release the handbrake and release the foot brake, otherwise the electric vehicle will not run normally.

This is also because there is gas in the brake pedal line or brake pump, or the car brake pads are thin, you can open the release valve of the rear brake master cylinder first.

The step is to hit the expansion opener valve on the rear tire, and the other person to press the brake, keep pressing until the gas is exhausted and then tightened, and both rear tires must be released.

If there is no gas or there is no brake pedal at the end, it means that the brake pads of the car are thin, and you can go to the repair shop to adjust the brake pedal.

With its strong application, flexibility, simple maintenance, convenient and fast maintenance, high quality and low price, electric tricycle can dexterously walk through narrow streets.

Check whether the brake fluid is leaking, the brake pads, and the full set of brakes There is a problem, it is best to go to the after-sales service.

I saw that there was no oil leakage, and there was no air leakage in the air brake pipe.

Have you fixed it? How to fix it???

Agricultural wind three-wheel brake, no brake for any reason,

Look at where there is an oil leak.

The adjustment method of the oil brake of the tricycle cannot be braked is as follows:

1. Press or hold the brake brakes on the back, give some pressure anyway, and hold them. Then loosen the screws on the rear brake caliper, which is connected to the brake disc, brake fluid.

will ooze, then tighten the screws in 2 seconds. The whole process is done by pressing the brakes until the last screw is released, and then repeating the process ten times to see if the stiffness is not enough.

2. The disc brake consists of a brake disc connected to the wheel and a brake caliper on the edge of the disc. When braking, the high-pressure brake oil pushes the brake pad to press the brake pad to produce a braking effect.

3. Disc brakes are sometimes referred to as disc brakes. It can be divided into two types, ordinary disc brakes and vents. Ventilated disc brakes refer to drilling a large number of circular exhaust holes on the disc surface, or cutting the exhaust port or prefabricated rectangular exhaust duct at the end face of the disc.

Compared with ordinary disc brakes, the exhaust valve with air flow has a better cooling and heating effect.

Note:

When starting the vehicle, release the pedal for one step or so, 10 steps in a row, and brake the pedal.

Set to a low position, on the outside quick torque exhaust port, torque after two seconds. The people on the bus continue to pedal, and the people outside the car are outside the torque exhaust port, tightening the exhaust. Repeat a few more times. until no air is flowing out of the exhaust port.

All wheels need to be ventilated. Pay attention to the brake fluid.

At the same time, it is also necessary to pay attention to the deficiency of increasing brake fluid. If the brake pedal is not high enough after exhaust, it can continue to be discharged, and the brake softness problem can be solved after the installation of the line, and the brake can be carried out when the brake is low.

The brake adjustment of the Shifeng tricycle is to twist the brake screw. 1. First of all, spray some water on the brake adjustment knob of the tricycle.

2. After that, pull the brake lever to test the tightness of the brake.

3. After that, use a wrench to twist the brake screw, and the brake will become loose if you screw it outward, and the brake will become tighter if you screw it inward. In this way, the brakes of the tricycle can be adjusted.

In the use of the vehicle, the brakes should be checked and adjusted frequently, because your tricycle is not an automatic adjustment structure, so when you always release the air to see if there is air every time, whether the air is correct, if the air is not air, you can feel whether there is air when stepping on the brakes, then you must check whether the gap of the brake shoes is properly adjusted, if it cannot be adjusted, it is possible that there is a problem with the brake pads or brake shoe adjustment screws, which need to be repaired and replaced in time.

Summary. If the brakes are too loose, add some disc brake oil (disc brake oil pot is located on the right bulge of the front handlebar), there are two screws to tighten the square box, unscrew the screws and then adjust the pressure. Unscrew the screw to open the cover, and then keep opening and closing the brake lever to exhaust the air inside, and the exhaust can increase the brake sensitivity.

If the brakes are too tight, then the tires are still not smooth, and the air vents in the fuel tank may be blocked, so you can use a toothpick or other slightly thinner wooden strips to pass through the air vents in the fuel tank. Then pinch the brake handle and do not let go, find a screw cap of the front wheel, after removing, loosen the screw, the oil will flow out, the more you put the brake, the looser the brake, there is oil outflow you can screw it back, can not be completely put away, otherwise the brake effect is gone. Hope my answer can help you.

If the brakes are too loose, add some disc brake oil (disc brake oil pot is located on the right bulge of the front handlebar), there are two screws to tighten the square box, unscrew the screws and then adjust the pressure to adjust the pressure. Unscrew the screw to open the cover, and then keep opening and closing the brake lever to exhaust the air inside, and the exhaust can increase the brake sensitivity. If the brakes are too tight, then the tires are still not smooth, and the air vents in the fuel tank may be blocked, so you can use a toothpick or other slightly thinner wooden strips to pass through the air vents in the fuel tank.

Then pinch the brake handle and do not let go, find a screw cap of the front wheel, after removing, loosen the screw, the oil will flow out, the more you put the brake, the looser the brake, there is oil outflow you can screw it back, can not be completely put away, otherwise the brake effect is gone. I hope my answer can help you.

How to adjust the brake pads.

The best way is to adjust the ejector rod in the middle of the brake pad according to the tightness of the brake. If the brakes are weak, adjust the ejector rod a little longer, and tighten the brakes if the brakes are too dead. I hope my answer can help you.

The brake adjustment of the Shifeng tricycle is to twist the brake screw. 1. First of all, spray some water on the brake adjustment knob of the macro slide tricycle.

2. Pull the brake lever after the mold is used to test the tightness of the brake.

3. Use a wrench afterward.

It belongs to twisting the brake screw, and the brake will become loose if it is tightened outward, and the brake will become tighter if it is tightened inward. In this way, the brakes of the tricycle can be adjusted. Dan Bureau.

There is no pressure on the Shifeng tricycle to step on the brakes, and there is no brake when you step on it.

Hello, there is no pressure on the car when you step on the brakes, and the reasons for one foot are as follows? The first is this phenomenon caused by the problem of brake fluid, it is recommended to replace the brake fluid and re-empti it. The second is the pressure relief of the vehicle's brake master cylinder, which requires a new brake master cylinder.

The third situation is the problem of oil leakage from the brake cylinder or the brake pads, and it is necessary to check the brake cylinders and brake pads.

Summary. Hello, electric tricycle oil brake no brake solution: check whether the pipeline is leaking, find that there is an oil leakage pipeline to replace, disassemble the rear wheel to check whether the brake cylinder is damaged and leaking, if there is oil leakage to replace, when installing new brake pads, it is best to smear the appropriate butter at the fixed column and the swing of the rocker arm and the brake block spring to make it more flexible, remember that the brake pads can not be stained with oil, otherwise the brake can not brake or the brake has a strange sound, which will also reduce friction.

Hello, electric tricycle oil brake no brake solution: check whether the pipeline is leaking, find that there is an oil leakage pipeline to replace, disassemble the rear wheel to check whether the brake cylinder is damaged and leaking, if there is oil leakage to replace bright, when installing new brake pads, it is best to smear the appropriate butter at the fixed column and the swing of the rocker arm and the brake spring, so as to make it more flexible.

Dear, the electric hidden oil brake has oil and no brake solution to the slow reed method: this is caused by brake fluid leakage. As soon as there is an air leak, the brake fluid has to be replaced.

The brake fluid replacement method is:; 1. Disassemble the upper cover of the brake oil tank. 2. Drain the old brake fluid from the brake fluid box.

Drain brake fluid from the exhaust port on the disc brake disc.; 3. Pour new brake fluid into the brake fluid box, and the brake fluid is purchased from the store. 4. After pouring the brake fluid, first tighten the exhaust port screw, then keep pinching and letting go of the brake handle, continuously brake and release the brake, and discharge the air in the disc brake pipeline, which takes half an hour.

5. Feel the brake force, cover the brake tank lid and tighten the screws.

This problem is caused by the leakage of the vacuum pipeline or the damage of the brake booster drum, you can first use the vacuum gauge to check the vacuum pressure of the intake pipeline, in the case of the engine hot car idling, in the range of 28 33kpa, beyond this range, the generator or vacuum pump is damaged, within this range, directly replace the brake drum on the line, it is recommended to replace the brake drum and the brake master cylinder at the same time, be sure to use the original parts, Analogues will cause reliability decline and occasional brake failure, which will seriously endanger driving safety. The brake fluid must be replaced every 4 years, and in coastal areas for two years, so as to avoid excessive water content in the brake fluid that causes corrosion and damage to the brake parts.