Why does the computer show a memory error when it starts up and then it can t open anything?

You can reinstall the system and try it.

According to what you can know, it is generally according to what you can know that there is a problem with the settings in B iOS. This is actually a very good problem to solve, you just need to try to restore the BIOS to the default settings, but due to the wrong settings you made, and the firmware design may be flawed, you will not boot properly now.

Under normal circumstances, if the system finds that it cannot be started normally, it will generally automatically change the B iOS setting to the default setting, but I don't know why, your machine does not automatically give the default. This situation is generally easier to solve, because our motherboard firmware settings are generally stored in CMOS.

His type is the same medium as the running memory in our computer, that is to say, if you don't give him power, the data stored in it will be lost, and the firmware settings stored in it are stored, if he loses power and starts again when there is no setting information in it, the firmware will definitely re-establish the default settings and store them in it.

In this way, we only need to unplug the small battery on the motherboard that is responsible for power supply, and this memory will be gone, and the power supply setting will naturally become the default.

The specific operation method is to completely power off your computer, then press the boot button to make sure that the power canceling has been completely discharged, and then open the side panel of the case to remove the small battery on the motherboard, let it stand for at least 5 minutes, and then plug in the battery and start it again, which generally solves the problem. It should be noted that this will completely change the firmware settings to default, and if you do something else before this and start it again, you will need to go to the BIOS interface to restore the settings.

At the same time, the time of the system is also likely to become the factory time of the motherboard, and it is wrong to enter the system display at this time. Generally, if the system is connected to the Internet, it will be automatically calibrated and use the time of the network, if there is no calibration, you need to manually set the time.

Finally, let's talk about the exception of Xiaoqiao. There are some motherboards whose settings may not be stored in CMO S, there may be independent flash memory, in this case there may be other ways to restore the default, it is recommended to look at the motherboard manual, it may be a jumper.

2) If the above methods can't solve the problem, first soft and then hard, reinstall the operating system, don't install software, patches, drivers, etc., and see if there are still problems with booting? If you don't install drivers, patches, and software step by step, and find something that isn't suitable, don't install it.

Please note: If you restore the system or reinstall it, when installing drivers, patches, software and other things, be sure not to install the things that affect your accident this time, otherwise it will be restored or reinstalled in vain.

3) Whether there is a problem with hardware, such as hard disk, memory, graphics card, motherboard, etc., if it is caused by hardware problems, it is recommended to overhaul it.

If it is a program that appears at boot, see if there is this option in the boot startup, if there is a removal of it, if it is a system process, the above method is not applicable.

Make an analogy with a picture:

Clean the ash, especially the gold finger, scrub it with alcohol, and then put it on.

Shut down, plug and unplug the memory, turn it on, if it doesn't work, the memory may be over.

It is recommended that you try the latest plug-in I have encountered problems before I don't know if it can be useful Like antivirus I think you may have killed and killed again Hehe Reinstall the system. You've definitely thought about it, so give it a try.

First kill the whole virus, and then see if the hard disk space is not enough, if not, reinstall the system.

poisoned, it is recommended to remove the hard drive and reinstall the system instead of restoring it.

Poisoned, all formatted, just reinstall the system.

The system text is damaged, there is really no way, it is recommended to reinstall the system!

Memory error, either a loose memory module or a corrupted memory module.

It is possible that the hard disk is damaged, so the boot partition cannot be started, in this case, you can use U run to redo the system.

In this case, the memory corruption may be relatively large, you can make the USB flash drive as the magician's boot disk on other computers, and then check the memory in the start menu option.

The computer shows that it is as simple as reinstalling the system, and it is estimated that the maintenance point will be about 80 to install the system.

Turn off the computer, unplug the power supply, open the computer case, unplug the board and interface, use the hair dryer cold air bracket to blow the soot, you can use a soft brush to blow while brushing,. When finished, reinsert all the interfaces and boards. Take a look at the boot.

Generally, sudden unknown errors can be solved by this method.

Unplug the memory first, wipe the memory with an eraser, and if it is still the same, reinstall the system.