Don t install Nero. Use XP s built in burn function to burn a word

Sorry you can't use this method, you can use this method to test things from the inside to the outside, but you can't write documents in this way.

Disc burning has a beginning and an end (optical track), and if it doesn't start, it can't be written, and it can't continue to write after the end. Once the optical track of a normal disc ends, it is not possible to continue writing data. The end point of the rewritable disc can be changed by the burn disc drive (so you can write data at any time), but ** is also much higher than that of a normal disc.

nero is very simple software, there is a Chinese version, the current mainstream nero 8As long as you know how to use Word, I'm sure you'll be able to use NREO (which is easier than Word) and easier to use than the XP system's built-in burning software.

The XP system comes with a very easy burning failure, so it is not recommended, please use nero8 directly which can be found on the Internet, believe in yourself, how do you know that you can't use it? (If you want to burn Word, choose to create a data CD and engrave the folder containing Word into it.) Then put it in the optical drive of the other computer and move it to the hard disk as you said).

Nero doesn't have to learn, right? Can you use it when you take it? Just a few simple options, right?

Put the file into the CD, and then click on the upper left corner to write these files to the CD, it will prompt you to enter the name of the CD, which you can take at will, and then it will be automatically engraved, and it will be OK after carving, this is how the electronic document of my graduation project is engraved.

How easy it is to use Nero. Fool-proof operation. It is recommended to use nero....You do. It doesn't seem to work. Especially if method one can burn, it's just a shortcut. Besides, it can't be burned at all.

The issue of the nero serial number is still unsettled (I don't think Nero would use this stupid approach), and I've never had a problem with Nero anyway. Generally speaking, there are more problems with recorders. It turned out that there was a miscellaneous recorder, 10 disks could engrave six or seven copies, and then burned on a notebook recorder, and there was no problem.

Two years later, the burner on the notebook began to age, and the burned things could not be read, so I changed to an external *** recorder, which was used for nearly two years, and there was no bad show, even the cheapest disk was fine. Didn't care about the serial number during the whole process.

The nero you use is pirated, although your nero may also have a serial number, but nero has a solution to the serial number of piracy cracking, which is to make your burn disk scrapped.

I've said it all.,The serial number you use is a cracked version.,It's not genuine at all.,Nero can use it.,But it can make the disc obsolete.。 This is also Nero's solution to piracy.

You should be fine with the old one. ,The main thing is to use uninstalling software to clean up and reinstall the current one。 It should be fine.

XP has a burning function on its own, so you don't need to use Nero at all.

Without the burning function, even the best software can't burn.

The prerequisite for burning is to have a burning CD-ROM drive.

I'm from the HP pit.

I've encountered a lot of this situation.,Optical drive problem (send it to the repair station.,Let them copy down the optical drive number for you to bill.,Wait for the optical drive to you to take the book to change it.,So you don't have to leave the book in the maintenance station.,Don't delay your use.,Change the optical drive in 5 minutes)

Absolutely original,!

It's okay to use Power To Go. However, it is recommended to use the version. 100 minutes to engrave it, do you use CD or ***. There is a large-capacity CD, 800m. The general ones are 700m, or 730m.

I have power2go,nero8,convertxto*** three on my computer,The first two are equipped with computer fashion can engrave cd,The latter one can only engrave ***,**So far I haven't engraved it,I'm only engraving***

You can carve it for 100 minutes if you turn it smaller.

If it doesn't work, you can buy a *** blank disk.

When copying a disc.

The first choice is that you have to have a source disk,And then there is an option in nero called brother or "copy disc",After entering, you will be asked how much you copy、The speed of burning, etc.,When you choose the next step or start burning, you will be asked to put the source disk into the optical drive (there is only one optical drive,If it is an optical drive and a recorder, it is different),When the data in the source disk is read, the disc will automatically pop up,Prompt you to put in a blank disk,After putting it in, you will start burning,If it is two optical drives,There are options before burning, It's the source disc drive and the burn CD drive, you can find it yourself, it's very easy.

When a mirror is burned.

It's time to choose to open the image file after entering Nero, the following is to select the speed and the number of burns, the speed can be regretted to be about 16x, too fast will affect the service life of the disc after burning.

How to burn a system boot disc.

1.Open the Nero Burning Rom

Select"Burner"- Burn image files"

Here's a few words.,Now installed RAR will associate the iso.,So the icon may think it's a compressed file.,Its crack is really not cracked rock Yes,You show the suffix of the file to know that it's an ISO file.,Not a RAR file!

3.General engraved XP is recommended to choose"The disc is burned once"or"Discs burn 96 at a time"

As for the speed, it is best not to be too fast, it is recommended to choose 24x

Are you going to burn an ISO file? Select the burn image disc, and then select the ISO file to start burning.

If it's a pirated copy, just burn it, but remember the installation code.

It's not that complicated, the general burning system disk is very simple, you directly right-click on the ISO file to select the opening method, and then open it with Nero It will pop up a box, you just click to burn on the line!

You can directly engrave the image in the nero with this function.

Installation: Nero burning software.

Preparation: CD disk.

- Install the Nero burning software will automatically associate the ISO file (there will be a disc icon),Double-click the XP system ISO format file on the ISO file, the Nero burning program will pop up,Put in a blank disc,Click to burn it,Don't worry about the rest!!

Just burn the image file and you're good to go.

Choose to burn ISO image files at a speed of 24x or 16x!