Is the silicone water repellent made by adding a water enhancer? 20

It must be more than just a water enhancer.

How to use silicone water repellent agent:

1. Suitable for any painting method, painting, brushing and spraying. When using, the waterproofing agent and water are mixed evenly in proportion, and then put into the spraying container and sprayed. Try not to use it when it is close to the rainy season, or the temperature is below 0 degrees, and the confession of construction must be dry.

2. Using cement mortar, first mix and mix the waterproofing agent and water in the corresponding proportion, and then add the cement and sand together and mix before use.

Silicone water repellent precautions:

1. When the temperature is lower than 10 degrees, the silicone waterproof coating will be prohibited from construction under the condition of high humidity, and construction is also prohibited in bad weather.

2. Try to avoid mixing with other paints and coatings.

3. When painting, the wall is required to be dry, flat and clean, and if there is dirt or mold erosion, it must be cleaned first.

How to use:

1. Clean the surface of the substrate before use, and fill it with putty or cement slurry if there are cracks;

2. Before construction, slightly moisten the surface of the substrate for absorption;

3. Dilute to a concentration of 40 times or lower when using. If it is necessary to use a concentration higher than 20 times, it must be verified experimentally first, and the use of high concentration will lead to the formation of white residue on the waterproof surface;

4. The construction can be carried out with rags, sponges, brushes, rollers and sealing spray guns by soaking, spraying or brushing. It can also be incorporated into concrete;

5. After brushing, the treated surface is naturally dried, and the surface is painted a second time before drying. Keep it in water for at least 24 hours.

Precautions. 1. Before use, the concentration test of small samples should be carried out to ensure that the best effect is achieved;

2. If it comes into contact with it, rinse it with water immediately.

3. If the temperature is too low in winter, the crystal structure of the product will freeze, heat to room temperature, the solution will return to transparent, and the active ingredients of the product will not be destroyed, and you can continue to use it.

Pro, this question is answered by me, oh dear, dear, silicone waterproofing can not replace the wall reinforcing agent, oh dear, can't be completely waterproof, oh dear, the following is the role of the wall reinforcer, oh pro: 1Consolidating the substrate This reinforcing agent has the effect of consolidating the substrate, it is a kind of interface agent, which has the effect of connecting the previous and the next after use, and other substances can be well covered on it.

2.It has excellent permeability The wall reinforcing agent itself is very permeable, and after the wall is used, its surface base material can be fully infiltrated by it, so that the base layer becomes more dense, so as to improve its attachment to Gaozhou 3Improve the adhesion of the smooth base After the use of reinforcing agent on the wall, the adhesion ability of the base can be greatly improved, especially for the smooth base wall<>

If my answer is helpful, please give it a thumbs up (rate it in the bottom left corner) <>

I look forward to your praise, your efforts are very important to me, and your support is also the driving force for my progress<><

If you are satisfied with my answer, <>

You can take a picture to click on my avatar for one-on-one consultation. Finally, I wish you good health and a good mood! <>

What is the specific content of silicone waterproof coatings, the following Zhongda consultation will answer for you.

Silicone waterproof coating has excellent high and low temperature resistance, weather resistance, water resistance, resistance to various gases, ozone resistance and ultraviolet degradation resistance, etc., painted on the wall, which can not only protect the normal ventilation of the wall, but also resist the erosion of rain, so that the wall is moisture-proof, anti-corrosion, freeze-thaw resistant and maintain luster, as long as the construction is done properly, the life of the waterproof layer can reach 10 15 years, it is an ideal building waterproof material.

1. Silicone waterproof coating.

Silicone waterproof coating is a kind of architectural waterproof coating based on water-soluble silicone resin and emulsified by advanced technology.

Color silicone waterproof coating is a water emulsion waterproof coating prepared by mixing water, inorganic fillers and various additives with silicone rubber latex or other emulsions as the main base material, which has the excellent characteristics of both coated film waterproof and permeable waterproof materials, and has good waterproofness, permeability, film-forming, elasticity, rapid adhesion, extensibility and high and low temperature resistance.

2. Silicone rubber waterproof coating.

Silicone rubber waterproof coating is based on the compound of silicone rubber emulsion and other emulsions as the main base material, mixed with inorganic fillers and crosslinking agents, catalysts, toughening agents, defoamers and other chemicals.

Emulsion-type waterproof coating formulated with additives.

This product has the excellent properties of both coated film waterproofing and impregnated waterproof materials, and has good waterproofness, permeability, film-forming, elasticity, adhesion and high and low temperature resistance.

This product has strong ability to adapt to the deformation of the base layer, can penetrate into the base and bond firmly with the base layer, cold construction, can be scraped, brushed, sprayed, easy to operate, fast film forming speed, can be constructed on the wet base layer, non-toxic, tasteless, non-combustible, safe and reliable, can be formulated into various colors of coatings, so as to facilitate repair.

Silicone rubber waterproof coating is a water-emulsion coating with water as the dispersion medium, and the polymer with a network structure is formed after water loss and curing. After the paint is painted on the surface of various substrates, with the infiltration and evaporation of water, the particle density increases and loses fluidity, when the drying process continues, the excess moisture continues to be lost, and the emulsion particles gradually contact each other and agglomerate, under the action of cross-linking agent and catalyst, the cross-linking reaction is continuously carried out, and finally a uniform and dense rubbery elastic continuous film is formed.

First of all, you need to figure out what causes water seepage, so that you can make a targeted construction plan. If the water seeps upwards from the ground, it must not be constructed with waterproofing agent, otherwise it will affect the life of the wall.

My waterproofing agent is technologically advanced and effective, and the waterproof effect can last a lifetime. If your situation can be applied with waterproofing agent, please feel free to contact us.

Silicone Some are still good waterproof coatings Look at the ones used in **, the general use of paraffin emulsion for paper.

Whether the waterproof effect is good or not depends on what kind of waterproofing agent is used.

Waterproofing agent is also divided into many varieties, the general water-soluble waterproofing agent on the market is an alkaline material, its ultraviolet resistance is poor, waterproof time is short, you should choose a solvent-based silicone polymeric waterproofing agent material with strong weather resistance, there is a silicon-based waterproof penetrant GJ-923 on the market, it is a transparent solvent-based silicone polymerization waterproofing agent, the waterproof life of the exterior wall is up to 10 years, the effect is good, the appearance is not changed, and it is easy to use.

It depends on how to use it, where to use it, the key is the quality of the product!

Waterproof engineering is a key engineering project in the process of decoration and decoration, they determine the specific situation of later use to a certain extent, especially in the southern area where the rainwater is relatively abundant, if the waterproof material or waterproof technology construction operation in the waterproof project is not appropriate, it is likely to lead to the later rainwater infiltration into the house, causing property losses and troubles, so today for you to give an example is a waterproof material that has a good reputation and evaluation, That is, the purchase information of silicone waterproofing machines.

1. Silicone waterproofing agent**

1. Silicone waterproofing agent for building waterproofing agent for kitchen.

Company Name: Anhui Bangmai Building Waterproof Environmental Engineering ****.

Starting Price: 160

2. High permeability silicone emulsion waterproofing agent Qingdao wall.

Company name: Qingdao Kunrong new materials****.

Starting price: 13 kg.

3. Jinbaihe potassium methosilicate high-quality silicone.

Company name: Jinan Jinbaihe Industry and Trade****.

Starting Price: 5000

Second, the formula of silicone waterproofing agent

The main material of silicone water repellent is polysilicone emulsion, after special processing, its silicon atoms, oxygen atoms and atoms on the fiber will form hydrogen bonds, valence bonds, such a structure makes water droplets unable to bed head. Its color is colorless or pale yellow, and after being brushed is a colorless and transparent film. This film allows the rainwater to bead down on the ridges, while the base layer remains dry.

The production process of silicone water repellent agent is very complex, it is a technology developed by the United States, and it is now widely used in many developed countries in the world. Because of its good permeability, it forms a waterproof layer in concrete, mortar and cement.

3. How to use

1.First of all, it is necessary to know in which occasions the silicone waterproofing agent can be used, which can be used in the hard waterproofing project of building roof, the waterproofing project of underground facilities, the leakage prevention project of the pool and the waterproofing project of the exterior decoration.

2.As with other waterproofing materials, the base layer should be treated before applying the silicone waterproofing agent. Treat the ash layer, stains, cracks, holes, etc. on the base surface, and remove any moss if there is moss.

3.Brush or spray the silicone water repellent evenly on the surface of the building, without missing any corners. Although the silicone waterproofing agent is not toxic, it should be avoided from splashing into the eyes.

Although Xunpeng has the impression that silicon products are very good and are especially suitable for making some accessories and tools, in fact, similar to the above, they can also be processed into silicone waterproofing agents. They are relatively stable in performance compared to ordinary waterproof building materials, suitable for use in the field of home improvement building materials, and a variety of sizes and specifications can also cater to the individual needs of consumers themselves, to ensure that we are more satisfactory to use and waterproof effect, then interested friends may wish to refer to the above before the purchase of understanding it.

You can get it for free

Water repellent agents have several advantages over other waterproofing materials. Clause.

First, the cost is cheap. Clause.

Second, the effect is good and the duration is long. Clause.

3. It is easy and fast to use, and you only need to introduce the waterproof agent into the material to use it.

What are the factors that affect water repellents**?

Clause. First, the type of waterproofing agent is determined, and the waterproofing agent can be skillfully reversed into leather waterproofing agent, textile waterproofing agent, mortar waterproofing agent, silicone waterproofing agent, etc., each of which is used in different fields.

Clause. Second, how much is a barrel of waterproofing agent is also related to the brand of waterproofing agent, generally speaking, the more well-known the brand, the higher the first, because the greater the popularity, the quality of the product is guaranteed.

Clause. 3. The toxicity of the waterproof agent is low, and the safety and environmental protection have basically reached the level of oral five poisons.

Clause. Fourth, how much is a barrel of waterproofing agent is also related to the model, and the quality effect of some newly developed waterproofing agents is better than that of the old ones, but they are often higher than the old ones.

Precautions for the use of silicone waterproof honorifics:

1.Before painting or spraying, the treated object should be cleaned of dust, floating ash, slag and other items on its surface.

2.Before treatment, the surface of the treated object should be a little drier, so that the active ingredients of the waterproofing agent can penetrate and better play its waterproof role.

3.Mix the waterproofing agent with water 8 20 times, stir evenly and spray or brush on the surface of the substrate, generally criss-cross when brushing, and shall not miss the coating, and generally brush once to have a satisfactory waterproof effect. Depending on the density of the substrate and the requirements for waterproofing, additional brushing can be applied after the first coat of drying.

4.This product should be allocated according to the construction needs, and it should be used immediately. The diluted solution should not be left for a long time, if the diluted waterproofing agent is not used up at the moment, it needs to be sealed and stored within 6 months.

The active ingredient of silicone waterproofing agent can penetrate into a certain depth of the surface of the object to play a waterproof role, but it does not have a waterproof effect on obvious cracks, and the cracks should be filled first, and then waterproof construction.

5.The silicon waterproofing agent product is suitable for construction at 4 40 ambient temperature, the low temperature film forming time is slow, the high temperature solution evaporates quickly and affects the absorption, and it can not be washed by rain within 24 hours after construction, and the outdoor operation in summer is generally 4 hours into a water-repellent structure, and the outdoor operation in winter can be a water-repellent structure for 10 hours. After 48 hours, the water repellent test can be done, and the waterproof effect is best after one week of natural maintenance.