Why can t solar energy go up on the water, what is the reason why the solar can t go up on the water

There are two ways to water on solar energy: automatic and manual.

Automatic water feeding: when the solar water temperature exceeds 60 degrees Celsius and the solar water tank is not full; When the power is temporarily cut off or the power supply of the controller is turned on again; When the solar water level is insufficient, the water system is controlled by the solenoid valve, and the solenoid valve will automatically close when the water tank is full.

Manual water filling: Pull the mixing valve to the water filling position to add water to the solar water tank, and then pull the handle back to its original position after the water tank is full. (The handle of the mixing valve is rotated 180 degrees at the boundary between cold and hot water to fill the water tank).

Reasons why the solar tank can't be watered:

1. The water pressure is insufficient or the water level of the water source does not exceed the water level of the water tank, resulting in a negative height difference.

2. Pipeline blockage.

3. The electric pump valve is faulty and cannot be opened.

Solution: 1. Increase the water pressure and height difference of the water source to make its water level higher than the water level of the solar water tank. (Urban tap water is generally not lower than 4 pressures, since it can meet the normal water consumption of residents, there will be no negative height difference).

2. Check and dredge the water supply pipeline.

3. Repair and replace the solenoid valve.

Solar water heater does not water solution: First, check whether the tap water pressure is normal (loosen the joints at the connection between the water tank and the sewer pipe, open the manual water supply, and see if there is water flowing out of the nozzle of the sewer pipe, if there is no water, the water pressure is low, it is recommended to miss the water during peak hours). Second, if you use the controller to use the water, check whether the sensor of the controller is normal (see whether the water level and water temperature of the controller are displayed normally, if the display is not normal, the controller probe needs to be replaced); Check whether the water solenoid valve is normal (loosen the joint of the solenoid valve towards the end of the solar water heater, press the water button on the controller to see if there is water flowing out, if not, judge that the solenoid valve is faulty, and the solenoid valve should be replaced directly).

1. The battery valve is blocked; 2. If there is no battery valve, the water supply valve is blocked; 3. Water pressure problem, can't look at other people's homes; 4. There is a water leak in the main engine part upstairs, and it flows out on the side; 5. The sensor is broken, and it can only go up to the water, and then it stops. There is a problem with automatic water feeding; Inspection method: 1. Observe the total tap water meter when putting on the water to see how fast and slow it turns.

Is it going to turn all the time. 2. Turn off the valve of the solar energy, and at the same time turn the water to the side of the hot water to see if the water comes out, the water shows that the solenoid valve is good, on the contrary, the solenoid valve is broken, if the water is different from the tap water speed, it means that the solenoid valve is blocked. 3. If it is automatic water supply, temporarily unplug the plug in the automatic meter, and then water on it, if there is no problem with the solenoid valve and valve, you can put water on the main engine.

The reasons and solutions for solar water heaters not producing hot water are as follows:

First, the vacuum tube of Taisolar is damaged, and the vacuum tube needs to be replaced for this reason.

2. Sewer pipes, valves or joints are leaking, and the sewer pipelines need to be overhauled.

3. The tap water pressure is too high, and the hot water cannot flow out, so the tap water flow needs to be reduced.

Fourth, the solar water heater is a multi-way water outlet, and there is a phenomenon of stringing water, so it is necessary to install an independent valve and close the valve.

5. If a fully automatic auxiliary water tank is installed, it may also be that the float valve in the auxiliary water tank is not closed tightly or fails, resulting in continuous replenishment of cold water and reduced water temperature, then the float valve and related components need to be replaced.

Solar water heater maintenance method

1. If you want to extend the service life of solar energy, then you should increase the correct use of solar water heaters in your life, especially when you are on the water, it is best not to use the water when there is sun during the day, and you should also pay attention not to let the solar energy work when there is no water.

2. To protect the solar water tank well, prevent the solar water tank exhaust hole from being blocked, do not install other auxiliary tools by yourself, and check the exhaust hole of the water tank every once in a while, and repair the problem in time.

3. Do not place any items around the solar energy to avoid damaging the vacuum tube of the solar energy due to natural factors, and the solar energy can not be moved or reinstalled at will after installation.

Winter solar water does not go to the solution:

1. Replace the control panel.

If the water in the solar energy is enough, but the control panel of the solar energy still shows that the water level is not enough to put on the water, then it proves that there is a problem with the control panel of the solar energy, and we need to replace the control panel of the product.

2. Increase solar water pressure.

If the water pressure of the solar water is too low, then the water can not go up, if this is the case, you need to buy a water pressure increase pump, as long as the water pressure increase pump is installed, you don't have to worry about the phenomenon that the solar energy is not watery because the water pressure is not enough.

3. Repair the solenoid valve.

If there is no water in the solar energy, but the water of the solar energy can not go up, we can consider whether there is a problem with the solenoid valve of the solar energy, because the water of the solar energy needs to pass through the solenoid valve, if the solenoid valve of the solar energy is faulty, it is necessary to repair the solenoid valve of the solar energy, otherwise the solar energy will never be able to go to the water.

In the early days, the most widespread application of solar energy was to heat water, and today there are millions of solar water heating installations around the world. The main components of the solar water heating system include a collector, a storage device and a circulation pipeline.

In addition, there may be auxiliary energy devices (such as electric heaters, etc.) for use when there is no sunlight, and there may also be water for strong circulation, devices to control the water level or power part or temperature, and pipelines to receive loads, etc.

The reasons why the solar water does not go on the water in winter are: control panel problems, solar water pressure, solenoid valves, and water pipe problems.

1. Replace the control panel.

You can see if the water in the solar energy is enough, if the water in the solar energy is enough, but the control panel of the solar energy still shows that the water level is not enough to need water, then it proves that there is a problem with the control panel of the solar energy, and we need to replace the control panel of the solar product.

2. Increase solar water pressure.

If the water pressure of the solar water is too low, then the water can not go up, if this is the case, you need to buy a water pressure increase pump, as long as the water pressure increase pump is installed, you don't have to worry about the phenomenon that the solar energy is not watery because the water pressure is not enough.

3. Repair the solenoid valve.

If there is no water in the solar energy, but the water of the solar energy can not go in, we can consider whether there is a problem with the solenoid valve of the solar energy, because the water of the solar energy needs to pass through the solenoid valve, if the solenoid valve of the solar energy is faulty, it is necessary to shout to repair the solenoid valve of the solar energy, otherwise the solar energy will never be able to go to the water.

4. Replace the upper and lower water pipes.

The upper and lower pipes of the solar energy have a certain thermal insulation performance, if the thermal insulation performance of the upper and lower solar stoves is not good enough, and it will not be able to go to the water if it is frozen in winter, then we need to replace the upper and lower pipes of the solar energy in time, so that it will not be frozen, and it will not affect the water of the solar energy.

What you need to know when using a solar water heater:

1. The water stored in the solar water heater should be discharged regularly according to the local water quality. The drain time can be selected in the morning when the temperature of the collector is low. You can't store it in solar energy all the time.

2. For the surface of the solar water heater, according to the amount of dust and regular wipe test, rainwater can play a cleaning role, and keeping the surface of the water heater clean can obtain higher heat collection efficiency.

There may be a few points: 1. System failure, such as pipeline freezing, system aging, etc.

Second, the solar radiation intensity is too low, the original solar system water cycle principle is the power brought by the difference in the density of hot and cold water, low solar radiation may lead to insufficient water heating, insufficient circulation power between cold and hot water, resulting in no response to the water.

Solution: 1. Replace the control panel.

You can see if the water in the solar energy is enough, if the water in the solar energy is enough, but the control panel of the solar energy still shows that the water level is not enough to need water, then it proves that there is a problem with the control panel of the solar energy, and we need to replace the control panel of the solar product.

2. Increase solar water pressure.

If the water pressure of the solar's ** water is too low, then the water is not able to go to the middle, if this is the case, you need to buy a water pressure pump, as long as the water pressure increases the installation of the pump, you don't have to worry, because the water pressure is not enough, resulting in the phenomenon of solar water.

3. Repair the solenoid valve.

If there is no water in solar energy, but it will not be able to do solar water into account, we can consider the question of whether the solenoid valve is solar or not, because the language is that solar water needs to pass through the solenoid valve, if the solar solenoid valve fails, the solar solenoid valve needs to be maintained, otherwise the solar energy cannot be on the water.

The reasons why solar energy is not on water are as follows:

1. Solenoid valve problem

When the magnetic valve fails, it will also make it unable to use water. The way to confirm is very simple, press the water button first, and then open the hot water valve, if there is water out, it proves that the solenoid valve is working normally, if there is no water out, it proves that the solenoid valve is faulty, and this situation should ask a professional to overhaul or replace the solenoid valve.

2. Water pressure problem

If the water pressure is too low, the water will not reach the upper part of the tank, and in other cases, the inlet pressure of the solenoid valve will prevent the water from being filled. It is recommended to add a booster pump to make the water leakage more secure and secure.

3. Problems with the control panel and automatic controller

If the control panel shows no water, open the hot water valve to see if there is hot water, if the automatic controller fails and cannot transmit the signal, it will also cause the control panel to show no water, but there is actually water. It is recommended to replace the control panel and sensors.

4. The vacuum tube is damaged

If you return to this section to water the solar water heater during the high temperature at noon, because the temperature in the vacuum tube itself is very high, if you suddenly encounter cold water with a lower temperature, it is very likely that the vacuum tube will be easily damaged. As a result, the water pipe is easily damaged and cannot be supplied with water. It is recommended to choose the water time before sunrise or 1 hour after sunset.