What are the steps to fill up motor oil?

1.Check the oil 1: The car rests for five minutes and then checks the oil.

If you check the oil immediately after turning off the car, you will get an inaccurate reading because some of the oil is still on top of the engine. Keep your car on a level, even surface to make sure you're not checking for sloping oil. Most cars are manufactured.

2.Choose the right oil 1: The oil recommended in the instruction manual. Knowing the different quantities and grades on the oil package will make you an expert when it comes to motor oil and will help keep your car flat.

1.Warm up the engine.

2.Open the engine filler oil port cap.

3.After lifting the vehicle, remove the engine guard, remove the oil pan drain screws, and release the old oil.

4.Drop the vehicle and remove the old oil filter.

5.Open the new oil filter, take an appropriate amount of new oil and apply it to the sealing ring, wipe the oil and dirt on the joint part of the filter with a clean rag, screw on the new filter, and tighten it with a certain torque with an appropriate oil filter wrench, and wipe the appearance and joint part of the new filter.

6.Screw on the oil drain screw, put down the vehicle, fill with new oil, check the oil level, start the vehicle to idle and run at medium speed for a while, during which pay attention to observe whether the oil filter is leaking, and complete the operation after everything is normal.

First of all, make sure that the oil bottom screw and the oil filter element have been tightened, open the fuel filler hole cover, insert the funnel, pull out the oil dipstick, start to refuel, add to about three liters when inserting the oil dipstick measurement, see how much is missing according to the amount, to the upper line of the oil dipstick scale line, tighten the oil filler hole cover, and then turn off the engine after running for a minute or two, wait two or three minutes to pull out the oil dipstick to observe the oil level, if not enough to add a little more to the upper limit.

Engine oil is equivalent to the blood of the car, bringing endless power to the car and braking. Engine oil is indispensable for machine lubrication, especially for the engine. Too much or too little is not good, generally the highest liquid level is a little lower, and it is necessary to check regularly.

Before the inspection, the vehicle should be parked on the horizontal plane, and the engine should be started to idle for 5 mis "minutes";

Stop the engine, wait for 3 mis, pull out the oil dipstick and wipe it clean, reinsert the dipstick and take it out again, and record the oil level on the dipstick;

The correct oil level should be between the highest and lowest positions;

Beat the oil on the dipstick with your hand and check its viscosity to see if there is any gasoline smell and bubbles;

If the oil level is too high, even if the reason is inquired, it should be ruled out, and the cause may be caused by cooling water or gasoline entering the crankcase.

Five misunderstandings about the use of automobile engine oil:

Myth 1: Engine oil is often added but not changed.

For some German oil-burning car owners, it is not wrong to check the engine oil frequently, but only replenishing and not replacing can only make up for the lack of oil quantity, but cannot fully compensate for the loss of lubricating oil performance. During the use of engine oil, the performance will gradually decrease due to pollution, oxidation and other reasons, and there will also be some consumption, so that the quantity will be reduced.

Myth 2: The role of engine oil additives is large.

A good quality oil is a finished product with a variety of engine protection functions, and the formula already contains a variety of additives, including anti-wear agents, and the oil is most important to balance the formula to ensure that the performance is fully realized. Adding other additives by yourself not only does not bring additional protection to the vehicle, but is easy to react with the chemicals in the oil, resulting in a decrease in the overall performance of the oil.

At this time, the owner needs to prepare a clean paper towel or rag to pull out the oil dipstick under the engine.

3. Use a paper towel or rag to wipe the head of the oil dipstick clean, and then check the oil level inside the engine. The head of the oil dipstick will have a scale of organic oil quantity, which is usually identified by min and max, min is the lower limit of oil quantity, and max is the upper limit of oil quantity.

4. The owner can add oil to the vehicle according to the scale on the oil dipstick, and add it to the center of the two scale lines in the best position.

When the owner uses the vehicle, he needs to check the oil level of the vehicle regularly, under normal circumstances, the new car is checked once every 3-4 months, and the older vehicle needs to be checked once in about 2 months.

1. Place the old oil container under the oil pan in the lower part of the engine compartment of the vehicle;

2. Unscrew the oil filter element with a wrench and take it out;

3. Slowly unscrew the oil drain bolt of the oil pan, release the old oil, and reinstall the oil drain bolt after a period of release, do not tighten the bolt too tightly to prevent the oil pan from being damaged;

4. Tighten the screws after putting it clean, not too tight, and then pour the oil into the engine and screw on the oil filter element.

Engine oil is the lubricating oil used in the engine, which is composed of base oil and additives, known as the blood of automobiles, mainly containing anti-wear additives and cleaning agents, dispersants and multi-grade oil viscosity index improvers.