How to fill in IP 5 for the first and second computers of the road gamer

Connect the router to the port, then connect the rest of the machines to the router, use any machine as the host, log in the network card, and then assign IP to all the machines, the specific operation is to select the local connection - > properties - > internert protocol. In fact, the router is a small gateway, and its IP is the default (, the host is set.

The rest of the machines are randomly set from to, and the next time it starts, which machine starts first, is the host. Haha, it's all done, it's a lot of fun!

Supplement: If you want to increase the number of computers in the future, you can buy a hub or switch to connect to the router to increase the number of ports.

Using a router may have some impact on the speed of the network, but in theory it is not very significant, and if there are special circumstances, you will have to consider other options.

Good luck, friend!

Set the gateway of the second device to the IP address of the first device

Default mask.

The router has its own fixed IP address, which is stated in the manual, and can be used to access the router's management interface from the browser. This address is also the gateway for all clients.

Here's an example: Let's say my router's IP is:

The client's IP address can be set from :. For example, the No. 1 machine is: The No. 2 machine is:At the same time, the subnet mask is set to: Gateway:

If you are using ADSL, you can go to the management interface of the router, set the router to dial automatically, and replay the disconnection and replay. When turned on, all clients have access to the Internet and can communicate with each other.

You don't need to set the IP, you can get it automatically. Just set up a host.

No problem. Your router has IP auto-assignment turned on. It's not a wireless router, it's okay to turn it on, don't care. It can be used normally.

It's okay, you can use auto-fetch.

If the external IP is the static IP assigned to you by the cell broadband or the LAN port of the higher-level router), then you set the network of the routing WAN to the static IP mode, and the IP is! The LAN port is set to the WAN port, and the WAN port of the host and router under the LAN is the WAN port.

The WAN port connection is static, and a public IP can be set at will, such as Mask:

If you want to set a static IP to allow LAN interconnection, then turn off DHCP, and configure the address of this network segment on the PC; If static IP addresses and dynamically acquired IP addresses are allowed to coexist, you can set the CIDR block IP address without disabling DHCP.

After reading your question, DNS settings are based on the region, is your router used by the company, the router settings are the same as those at home, but if you want to use a fixed IP, it is in the DHCP in the router, and the method is to set up a static DHCP, and bind the MAC address and IP address of the computer.

The computer can be directly connected to the LAN port of the router! Then manually set the IP address in the network connection and you're done!

You are dizzy, every computer wants to go online, or if you use a router to be in a local area network, you must have an IP, it will be automatically assigned to the computer, two computers are in the same router, the network segment is the same, the IP suffix is different, and everything else is the same.

There can only be one DHCP server in a network segment, that is, you can't turn on DHCP service on both routers, which will cause confusion, and you can only turn one on and not on One router, which means that you can only get automatic IP from one router.

And you also have to see how the two routers are connected, if it is the same level, then it can't be turned on, if it is the upper and lower level, then it is theoretically possible to turn on DHCP, depending on the practical application.

My own legion.

**Wire incoming wire connection - splitter connection - 1 ** Another 1 "cat" - "cat" out of the network cable to connect to the No. 1 router WAN main port - then use a network cable to connect to 1234 any branch port to connect to the computer, open IE and enter the router address to set up broadband connection OK.

Step 2: Remove Router No. 1 and replace it with Router No. 2, turn on IE and enter the router address, enter the remote web management option, change the address to any address (not the same as Route No. 1), and then disable the DHCP function in the DHCP option.

Step 3: Replace the No. 1 router with the same connection as above, and then use one network and one end to connect the No. 1 router to any branch and one end to the No. 2 router to any port (instead of the WAN main port). The layout setting is OK

The most recent one. Computer --- Router A --- Router B In this case, the address you get is Router A.

You can use the IP address to bind the MAC address of the NIC.

You don't need to set the IP address of the router, you just need to go in** to set it up, (remember to choose Auto DCHP and you don't have to set the IP address if you choose it) Auto DCHP will automatically assign the IP addresses of your two computers.

Want to use the same IP address for both computers? But subnets are different. Target.

You can connect the network cable directly to the computer and the router, and then go to PPOE dial-up Internet access, or connect to the Internet on the computer. (Online neighbors), if it still doesn't work, just use the landline to dial 10000 to inquire!

If you have a router, don't set up an IP or something.

Enter the anmin username and password as usual.

Follow the wizard settings.

1 IP open two I also play the new area I use the virtual IP software I use can open a lot of hehe.