The power calibration error of the recorder indicates that the power supply is calibrated incorrectl

This is how I solved the recorder power calibration error; I'm using the XP system of the new computer city, and I use the mud road to engrave butterflies to prompt the power calibration error, and even carved a few photos are costly, thinking that the recorder is broken, but the machine has not engraved 20 butterflies, how can it be broken? So I reinstalled the deep system and the problem was solved.

You try it too, and it might work out too!

I'm using the Deepsp3 Rapid Setup Version.

My machine is also BenQ, and I can't open it after buying it for a few months, and I have to knock it by hand to open it, which is depressing!

In more than 1 year, only 20 plates have been engraved, and you have engraved too few.

If you can succeed on someone else's machine, it may really be that the voltage is unstable, try changing the power supply.

Do you always use the same type of burning disk? Sometimes, if you change an incompatible disk, you will also have a power calibration error.

According to your description, it should be caused by an unstable power supply.

The brand model of the power supply is???

The internal aging of the recorder requires more power when burning the same disc, and the power supply is not enough, so it cannot be supplied naturally, and the possibility of aging the power supply is not ruled out.

1: Open the chassis and remove the optical drive.

2: Disassemble the optical drive.

3: Remove the data cable of the laser head.

4: There are two small potentiometers under the data cable interface, both of which are adjusted to the middle of the potentiometer.

The problem is absolutely solved.

The reason is that your laser head is adjusted according to a certain disc, and then you have engraved the disc n times.

It's a little old.

Don't say that you only engraved 20 times, after all, it is not a professional recorder, just a general one.

Let's save it.

As for why you can use someone else's power supply, it's because the current of the power supply is still more or less different.

It is recommended to change to a power supply with higher power (the life of the optical drive after adjusting the laser head is limited).

This is the so-called optical drive is broken.,It's estimated that now in addition to reading the general CD.,Read the compressed disk.,Ghost installation disk,And burning*** can't do it.,And it's very picky.,When you encounter this kind of problem, you have to change the optical drive.,This can only be used as an ordinary ***.。

I once bought an LG engraved CD drive in 02, more than 6 years, or very good, I generally choose this brand of recorder, don't buy Samsung, I bought two are bad in a year, garbage things, and expensive death! Wipe.

Hello: 1. It may be caused by the burning disk problem. Starting Burning after Putting in the Disk collects information about the burning disc and then performs power calibration.

If the quality of the burning disc is not good or there are stains, scratches, deformations, etc. on the surface, resulting in the power required for burning is greater than the power provided by the laser head of the recorder, there will be a "power calibration error". It is recommended that you replace it with a new or another brand of burning disc.

2. Caused by the power supply of the recorder or computer, the aging of the laser head of the recorder, the stains on the head of the light grinding group, and the abnormal operation of the circuit controlling the optical head.

The above problems can generally be solved in 1. Hope it helps.

Let me mention a few possibilities for this scenario.

1.The laser head is grayed out. Under normal circumstances, there is a possibility of dust accumulation after 1 year, and the recorder is used too few times, and it is easy to accumulate dust.

2.The quality of the disc is poor, the workmanship is not good... Some brands of burning disks cut corners.

This is basically related to the accumulation of ash. In other words. The laser head of the recorder is a little gray.

In addition, the disk used is a little bit worse. But if the disk is better, it can still be barely burned. However, the storage time of the burned disk will be reduced.

If the dust accumulation is severe. Then no matter what disc you can't burn.

3.There is a problem with the recorder's data cable. Loosened and so on. This is less likely. Generally, loose data cables will cause the burning time to become very long. It was supposed to be 10 minutes, but if it is loose, it will become 30 minutes and so on.

4.The laser head of the recorder is damaged... This is also less likely. If you don't burn half of the machine, it crashes, loses power, or is damaged by external forces. Generally, it will not cause damage to the recorder.

Your situation. You can try it out with other brands, or you can change the burning software and Ashampoo to try it out.

If it doesn't work, disassemble the machine and wipe the laser head with clean water. If you don't know how to dismantle or like to use brute force, don't dismantle. Let's get a new one.

You can disassemble the optical drive, adjust the power, can be used for a period of time, and it is recommended to buy one, which is not expensive.

There are several reasons for this:

1. First of all, the recorder can't be opened, but the small liquid hand hole can be opened, which means that the rubber ring and other parts in the recorder may have been worn out.

2. If there is a power calibration error in the newly bought recorder, it means that the power required by the disc is greater than the power of the bald head, which should be a problem with the disc: the dye burning power of the disc is high, the disc performance has obvious stains or scratches, the quality of the local resistant disc is poor, the disc base and or the dye are uneven, and so on.

It is recommended to try another brand of platter.

3. If it is a recorder that has been used for a long time.

There is a problem with the bald head: the recorder has been used for a long time, the bald head has been significantly aged, the dirt is attached to the bald head, the mechanical system of the bald head is unstable, the circuit controlling the bald head is not working properly, and so on.

It is recommended to replace the recorder.

The optical drive is a consumable, and it is very complicated to repair, and there are few places to repair the optical drive, so it is recommended to buy a new one

In the process of burning, the recorder first collects the information of the platter, and then performs power calibration: a random laser is emitted on the burning platter, if the platter is of poor quality, the required laser power will be greater than the power of the optical head of the recorder, so that there will be a "power calibration error". In addition, there may be problems with the power supply, the laser head of the recorder, etc.

To solve this problem, you can troubleshoot them one by one:

The first step, first of all, the new recorder, the laser head should be no problem. You can change the disc to another brand for burning. If the fault persists, proceed to the next step;

The second step, install the recorder to someone else's computer host for burning, if the burning is normal, it means that there may be a problem with your computer's power supply, you can check the power interface or replace the power supply, upgrade the burning software to test; If the burning failure persists, it means that there is a problem with the recorder itself, and it is necessary to consider repairing or replacing it.

Note: If the recorder that has been using the normal *** recorder suddenly has the problem of "power calibration error", after excluding the influence of the platter, it can basically be judged that the life has been reached and the recorder needs to be replaced!