Can you build a wall where there are no beams in a frame structure?

Frame structure. Where there are no beams, you can make a lightweight partition wall, but a masonry wall is not good (unsafe).

Lightweight partition panel is a new type of energy-saving wall material, it is a wall material that looks like a hollow floor slab, but it has male and female falcon grooves on both sides, and only the board needs to be used when installing.

Standing up, the male and female falcons are coated with a small amount of caulking mortar and then assembled together. It is made of harmless phosphogypsum.

It is composed of a variety of industrial waste slags such as light steel slag and fly ash, which is cured by frequency conversion steam pressure. Lightweight partition board has the advantages of light weight, high strength, multiple environmental protection, thermal insulation, sound insulation, breathing and humidity control, fire prevention, rapid construction, and reduced wall cost. The inner layer is equipped with reasonable layout of heat insulation, sound absorption inorganic foam profiles or other insulation materials, the wallboard is poured by the assembly line, leveling, scientific maintenance, high degree of production automation, many specifications and varieties.

Masonry construction can not be carried out in the place without beams, when the ground is settled, the masonry wall will crack or even collapse, if you have to carry out masonry construction in the place without beams, you can do the "ingot" foundation after the ground excavation or plant reinforcement on the ground beam to make the strip.

If you need to make a masonry wall, you must ask a professional reinforcement company to issue a calculation basis to see if you need to reinforce.

Masonry is not good, the load is too large, the slab will crack, or consider a lightweight partition.

You can build a simple wall, you can tear it down.

It is not possible to build a wall to isolate the space, but a lightweight wall such as a double-sided plastic gusset can be used to partition the space. For the weight of the masonry wall, the 10cm thick concrete slab is too thin, not how much steel bar, deflection and crack resistance are not up to the requirements.

If your plate is well reinforced, it is not a problem, otherwise it is not safe.

It depends on the reinforcement of your board and how it is matched. You can consider a lightweight build.

Dear, I'll answer this question for you. Yes, the second floor of the frame structure can be built on the first floor where there is a wall but no beams, but the corresponding conditions must be met, if it is still in the design period, this shows that the local frame structure is not to use the wall to bear the weight, and it does not have to be a wall below to make a wall, even if there is a wall below, the structural beam is needed to bear the gravity. If you want to renovate a building that has already been completed, you should use lightweight walls, such as 60 brick walls or 90 blocks, and take into account the size of the location interval during construction, sometimes the design is very open, such as the load and deflection calculations have reached the limit, and a lightweight partition wall system must be used.

During the epidemic period, remember to call the bend site for good prevention, wear a mask, try not to go to a large number of places, if you are satisfied with this time, please like it, thank you very much.

Do the math how much it will cost you to renovate your home

When decorating, many families will tear down the wall and build the wall in order to change the indoor pattern, but many people are not very cautious about demolishing the wall, causing many potential safety hazards. So can you build a wall where there are no beams? What do I need to pay attention to when building a wall?

Can you build a wall where there are no beams:

From the design point of view, the construction must be carried out according to the drawings, and the wall cannot be built where there is no beam, otherwise the force mode of the floor slab will be changed. However, a lightweight wall such as a double-sided plastic gusset can be used to divide the space.

What do I need to pay attention to when building a wall?

1. The load-bearing wall cannot be dismantled.

The load-bearing wall has the function of supporting the weight of the upper floor, so if the load-bearing wall is removed, then the entire building structure will be damaged, affecting the stability of the foundation.

2. Remove the wall fiber and pay attention to the smoothness of the cut surface, so that it can be painted later.

When dismantling the wall, you can first make a rough positioning on the wall, and then use a tape measure to accurately position it, and use a bullet line to play it. The wall can then be smashed to ensure that the cut surface is flat, and unnecessary waste of material is avoided.

3. The junction of the old and new walls is the key to construction.

When laying bricks to the junction of the old and new walls, it must be noted that in addition to the pay-off wall to maintain the verticality and flatness of the wall, the junction of the wall must also be beaten off with white ash, and then a layer of steel wire mesh is pasted to prevent the wall from cracking.

4. When building the wall, it must be carried out in accordance with the drawings.

If the designer has re-planned the space according to the needs of the owner, it is necessary to follow the designer's design drawings when building the wall. Avoid unnecessary waste.

Summary: The above is the introduction of the wall can be built in the place without beams and what matters need to be paid attention to when building the wall, I hope to help friends in need, the wall is the support of the whole house, so the quality of the wall directly affects the safety of the house. Therefore, you must pay more attention to the decoration when building the wall.

Enter the area and get the decoration for free**].

Summary. <> pro

Hello, it is a pleasure to serve you: Regarding your questions: the following comments are provided for your reference:

Absolutely. However, the following conditions apply. 1.

If it is the design stage, the structure needs to be beamed, that is, the frame structure is not load-bearing by the wall, and it is not necessary to have the wall below to make the wall. Even if there is a wall underneath, the structure needs to be made as a beam to bear the load. 2.

If you want to renovate a building that has already been completed, it is recommended to use lightweight walls. For example, light steel keel gypsum board partition wall system, high-strength cement hollow board system, 60 brick wall or 90 blocks can be. However, it depends on whether the span of the location of your construction is relatively large, because sometimes the design is not very conservative, and the load and deflection calculations have already reached the limit, so you need to choose a lighter partition wall system.

The frame structure is loaded by beams and columns, and the wall only plays the role of filling and enveloping, and does not bear the load. In the construction of frame structure, the construction process of wall masonry first, and then supporting beams and column formwork is wrong. It is not only very difficult to construct, but also leads to construction quality problems and even construction quality accidents.

The first floor of the frame structure has walls, but there are no beams, and the second floor should be built in the corresponding place.

<> pro

Hello, I am happy to serve you, please describe your problem more specifically: "There is a wall on the first floor of the frame structure, but there is no beam, is it okay to build a wall in the corresponding place on the second floor" and talk to the teacher in detail, so that the teacher can better help you solve the problem of the wheel and the beam. <>

<> pro

Hello, it is a pleasure to serve you: Regarding your questions: the following comments are provided for your reference:

Absolutely. However, the following conditions apply. 1.

If it is the design stage, the structure needs to be beamed, that is, the frame structure is not load-bearing by the wall, and it is not necessary to have the wall below to make the wall. Even if there is a wall underneath, the structure needs to be made as a beam to bear the load. 2.

If you want to renovate a building that has already been completed, it is recommended to use lightweight walls. For example, light steel keel gypsum board partition wall system, high-strength cement hollow board system, 60 brick wall or 90 blocks can be. However, it depends on whether the span of the position of your construction is relatively large, because sometimes the design is not very conservative, and the load and deflection trace calculation have already reached the limit, so it is necessary to choose a lighter partition wall system.

The frame structure is loaded by beams and columns, and the wall only plays the role of filling and enveloping, and does not bear the load. In the construction of frame structure, it is wrong to first build the wall masonry, and then support the beams and column formwork. It is not only very difficult to build, but also leads to construction quality problems and even construction quality accidents.

Summary. Kiss is happy to answer for you: For frame structures, do you have to build every wall on concrete beams?

Kiss not necessarily, the load-bearing wall should be built on the beam, and the partition wall should not be used. The walls in the frame structure are all non-structural load-bearing infill walls (except shear walls), and concrete beams are generally provided under the walls (under the concrete slab). That is, you are talking about the wall built on the beams.

For frame structures, do you have to build every wall on concrete beams?

Kiss Kiss I am glad to answer for you with a sock: For the frame structure, is it not necessary for each wall to be built on the concrete Wu Bi soil beam?

The walls in the frame structure are all non-structural load-bearing infill walls (except for shear walls), and concrete beams will be provided under the wall (under the concrete slab). That is, you are talking about the wall built on the beams.

I converted my suite into a single apartment, and I didn't see the walls, and the beams were not built.

Kissing is not a requirement for every wall.

I've changed it.

Every wall is out of place.

That's okay, and there's no clear rule about that.

Is it safe?

It is a seven-and-a-half-story building.

There is no relationship with the kiss.

I changed it to three, four, or five floors.

Kiss, it's okay, you can rest assured.

Summary. There must be a wall or column under the beam to support it. The beams support the components in the superstructure of the building and the full weight of the roof, and are the most important part of the superstructure of the building.

Beams transfer the load on the floor to the columns or walls through supports (support points), and then from the foundation to the foundation and then to the crust. Beams and slabs together form the floor and roof structure of the building. Compared with other transverse stress structures (such as trusses, arches, etc.), the mechanical performance of the beam is poor, but it is simple to analyze and easy to make, so it is still widely used in small and medium-span buildings.

Beams are mainly subjected to bending moments and shear forces and sometimes torques during load action.

Where there are columns in the architectural design, do you have to make beams? Does the place where the wall has to be made of beams?

There must be a wall or column under the beam to support it. The beams support the components in the superstructure of the building and the full weight of the roof, and are the most important part of the superstructure of the building. The beams transfer the load on the floor to the columns or walls through the supports (support points), and then from the foundation to the ground and then disperse to the crust.

Beams and slabs together form the floor and roof structure of the building. Compared with other transverse stress structures (such as trusses, arches, etc.), the mechanical performance of the beam is poor, but it is simple to analyze and easy to make, so it is still widely used in Zhongxianghui small-span buildings. Beams are mainly subjected to bending moments and shear forces, and sometimes torques, under the action of return loads.

Columns and walls are load-bearing members that bear the axial pressure of the section in the building structure, the column is a linear member that bears the load parallel to its longitudinal axis, the cross-sectional size is less than the height, and the wall mainly bears the vertical component that is parallel to the wall direction, they all belong to the compression member, and the load is transmitted to the foundation, and sometimes it also bears the bending moment and shear force. The foundation is a structural component that transmits the superstructure loads from columns and walls to the foundation. There must be a wall or column under the beam, so that it can be used as a support for the beam; Supported by the support of the noisy seat, the external force is mainly transverse force and shear force, and the component with bending as the main deformation is called a beam.

1. Functionally, there are structural beams, such as foundation ground beams, frame beams, etc., which together form a spatial structure system with vertical components such as columns and load-bearing walls; There are structural beams, such as ring beams, lintel beams, connecting beams, etc., which play a structural role such as crack resistance, seismic resistance, and stability. 2. According to the structural engineering attributes, the beam can be divided into: frame beam, frame beam supported by shear wall, inner frame beam, beam, masonry wall beam, masonry lintel beam, shear wall connecting beam, shear wall dark beam, shear wall frame beam.

3. From the construction technology, there are cast-in-place beams, prefabricated beams, etc.

I believe that when you decorate your house, you have heard that the load-bearing wall can not be removed from these related problems, in fact, you must know that these parts must be paid attention to in the decoration process, or it will bring danger. Let's introduce to you whether you can build a wall without load-bearing beams?

If you want to start from the design point of view, you have to build according to the drawings, then you can't build the wall without beams, or you may change the force mode of the floor slab. However, you can also choose lighter walls such as keel frames and gussets for space partitioning.

What aspects need to be paid attention to when building walls in the home.

1. Ensure the construction temperature.

Generally speaking, the height of the wall should be controlled below the meter every day. If it is rainy, then the height should not exceed meters, and the consistency of the mortar must be controlled. Every day, before the end of work or the shutdown, it is also necessary to put a row of dry bricks on the top surface of the wall, or cover it with a material, and the measures should be done.

2. Soak the bricks in water in advance.

The bricks are relatively dry and dry, and the bricks need to be watered two days in advance, and they must not be poured and used, and they cannot be directly put on the wall with dry bricks, which will also affect the stability of the wall.

3. The amount of sand should be controlled.

The amount of sand should also be controlled, usually medium sand is used. Moreover, it is necessary to strictly follow the sand design label to proportion, and not exceed the standard amount of sand.

4. The mortar should be mixed and used.

The mortar should be mixed and used, and the mixed should be used up within half a day. If the temperature is high, then it should be used up within 2 hours, if the hardening phenomenon is found, do not add water to stir it, and do not use the mortar overnight.

Summary: If you want to start from the design point of view, you must construct according to the drawings, then you can't build the wall without beams, or it may change the force mode of the floor. If you want to know more about related knowledge, you can **** Qijia net hole socks to consult.