Ask the cat how to connect to the wireless router 30

Plug a wired broadband network cable into the wireless router WAN port, and then use a network cable to connect directly to your laptop (or desktop) from the LAN port. Then open the browser, enter generally, or, (see your manual) enter the management and password, generally admin, enter the setup wizard, fill in step by step, according to your broadband** to make a choice, if it is adsl, you need to fill in the username and password, if it is a fixed IP address or not a fixed IP address of broadband, you have to fill in the necessary information, fill in all the way, very simple. For the security of data and wireless network, you go to the special wireless column to start the key, generally choose the wep method, fill in the key you want to set on it, pay attention to the number of key digits, look at the prompt on your page, and then select the route restart in the route, not manually power off, and then it's OK, search for the routing signal, enter your preset password everything OK

Maybe you didn't look at it carefully.

If there is a cat, connect the cat to the computer, and the cable is first plugged into the jack of a separate color behind the router, and then you can set it according to the router manual, remember that the computer can only be set up when connected to the router, and you are not connected.

The password of the broadband must be accurate, and then plug the network cable of the cat to the computer into the WAN port of the router, and plug a network cable into the remaining 4 sockets at will, open the web page, and enter it at the **"Or "see which one can enter the router, click next after entering, select the second one, that is, pppoe, enter the broadband and password, enter the password twice, set the password for the router in the next step, restart the router, and then connect to the Internet (the IP is best set to get automatically).

First of all, you need to know that if there are only cats, then dialing needs to be carried out on the computer, if the cat is connected to the router, then select PPPoe in the WAN port settings for Internet access, provided that your home network is that kind of password. Then set some corresponding router wireless passwords on it. Is there anything unclear that can be asked

You don't need to set up a cat, the cat defaults. No, please check:

1. The network cable from the cat must be connected to the WAN port of the router, and the WAN port light must be on.

2. The WAN port configuration is PPPoE dial-up, and you need to fill in your own broadband username and password to save it.

Recently, some netizens led a telecom optical brazing network, which was originally a very pleasant thing, but he didn't know where to start when setting up the telecom optical cat to connect to the wireless router, the following is "how to connect the wireless cat to the router" I hope to help. To you!

Optical modem connection wireless routing steps

The first step of wireless routing is to connect the WAN port of the router to any LAN interface of the optical modem.

Step 2: Reset the router and press the reset button on the router with items such as a pin for jujube filial piety.

The default password of the router is admin lowercase.

Step 6: Click "Finish" and the router will automatically restart.

It is to change the original network segment to the new one, because the telecom optical modem uses this network segment, and the router cannot be the same as the optical modem.

<> plug in the wireless router, don't answer the cat first, connect the computer to any LAN port of the wireless Xiaoxiang device, enter the browser to enter the settings page, and set it according to the PPPoe (ADSL virtual dialing) method. Then set the SSID, encryption method, and password again. Save, restart.

After setting, connect the network cable from the cat LAN port to the WAN port of the non-touching circular line router.

A router is a device that connects to the LAN and WAN of the Internet, and it will automatically select and set the route according to the situation of the channel, and send signals in the order of the best path. A router is the hub of the Internet"Traffic police"。At present, routers have been widely used in all walks of life, and various products of different grades have become the main force to realize the internal connection of various backbone networks, the interconnection between backbone networks, and the interconnection between backbone networks and the Internet.

The main difference between routing and switching is that the switch takes place at the second layer of the OSI reference model (data link layer), while the routing takes place at the third layer, which is the network layer. This difference determines that routers and switches need to use different control information in the process of moving information, so the way they achieve their respective functions is different.