There are too many terminals, what components can reduce the terminal interface

With heavy-duty connectors, connectors.

Definition: A component that connects a device to an external conductor. In electrical engineering, terminals mostly refer to wiring terminals, also known as terminals, which are divided into single holes, double holes, sockets, hooks, etc., from the material, copper silver plating, copper galvanizing, copper, aluminum, iron, etc.

Their function is mainly to transmit electrical signals or conduct electricity. In a project, it is an interface reserved for the post-station project by the pre-station project.

First of all, the terminal block must belong to electronic components, and electronic components are the general term for components and devices. Electronic components: Refers to finished products that do not change their molecular composition during production and processing in the factory.

Such as resistors, capacitors, inductors. Because it does not produce electrons itself, it has no control and conversion effect on voltage and current, so it is also called a passive device. Electronics:

Finger. It's better to take two, but it's okay to take three.

Hello! The general surface treatment of the terminals, the generally used brass terminals, and then there are tin-plated, silver-plated, and the wiring harness terminals inside the airbag are too sensitive, so gold-plated terminals can be used! Specifically, it depends on what kind of requirements you have for the parts you are producing.

Don't be fooled, the S terminal is an analog signal, HDMI is a digital signal, you can get it without using an adapter cable There is this kind of adapter cable for sale, but there will be no signal if you buy it back.

With heavy-duty connectors, connectors.

Open the lid and poke it out.

Hope it helps......

No more than 2 sticks. This is required by the installation wiring specification.

What is the maximum number of wires that can be connected to a terminal block of an electrical component? Can anyone tell me about it.

It's better to take two, but it's okay to take three.

2 root This is required by the specification.

It does not belong to the terminal, which generally belongs to the legal inspection product.

Terminals belong to connectors, and connectors belong to a class of electronic components.

We do terminal product classification to classify terminals as electronic components.

GB 50171-92: Clause.

6. Each side of each terminal should be one, not more than two. --

The terminal block is a kind of accessory product used to realize the electrical connection, which is divided into the category of connectors in the industry. With the increasing degree of industrial automation and the increasingly strict and accurate requirements of industrial control, the amount of terminal blocks is gradually increasing.

With the development of the electronics industry, the use of terminal blocks is increasing and varied. In addition to PCB board terminals, the most widely used are hardware terminals, nut terminals, spring terminals and so on.

In order to facilitate the wire connection, it is an accessory product used to realize the electrical connection. It is a metal conductor encapsulated in an insulating plastic piece with holes at both ends where the wire can be inserted.

For example, if there are two wires, sometimes they need to be connected and sometimes they need to be disconnected, then they can be connected with terminal blocks and can be disconnected at any time without having to solder them or entangle them, which is very convenient and fast.

With the development of microelectronic technology, PLC and DCS technology have been rapidly developed and applied on a large scale, and the functions of conventional instruments and unit control instruments have been replaced by various highly integrated control systems, so that industrial devices can achieve more flexible control schemes, and bring great convenience to maintenance and repair.

1. A full range of modular structure: the wiring accessories in the control cabinet are designed into a series of products with modular structure, including signal input and output, power distribution, etc., using standard installation sizes, transparent arrangement of components, and clear instructions, which are both beautiful and fast.

2. Comprehensive functions: It has many functions such as signal isolation and drive, loop power supply, card power supply, signal indication, alarm indication, loop protection, power supply protection, signal transfer, etc., which can support multi-brand safety barriers and isolators to comprehensively improve the quality of wiring.

3. Simplified design and wiring: The type of jumper on the board is used to solve the problem of differentiation and complexity of wiring between external equipment and system clamps. Signal transmission and power supply are cleverly and organically integrated, and the same card can be connected to different types of instruments and signals, only need to change the jumper on the board, reducing the line nodes.

The on-panel construction drawings are simplified to simple, which reduces the dependence of complex lines on the drawings, and completely simplifies the design of construction drawings and the process of intra-panel wiring.

4. Omit the terminal block: the pluggable terminal block equipped with the external terminal can facilitate terminal maintenance, and the terminal board can be replaced without removing the wiring. The spring terminal has the characteristics of fast wiring, reliable crimping and low failure rate.

1 The conductor can be connected directly to the terminal block, so there is no need for a special terminal block. The internal terminals are equipped with a dedicated interface and are quickly plugged into the PLC or DCS using special cables.

5. All-round protection, do not dismantle the line and stop the meter, omit the power distribution switch, and avoid misoperation: each signal circuit is equipped with a convenient insurance to provide all-round safety protection, and the user does not need to be equipped with a power distribution switch and a safety terminal for external equipment. In particular, it solves the problem of stopping the peripheral instruments of DCS and PLC systems, and repairs and dismantles external equipment as long as the insurance is unplugged without having to remove the wire, which is fast, efficient, safe and reliable to prevent misconnection.

The power circuit adopts over-voltage, over-current, and reverse connection protection measures to ensure the safe operation of system equipment.

6. LED indication and current measurement without dismantling the wire to facilitate maintenance and repair: the power supply circuit and signal circuit are equipped with a full range of LED signal indication and insurance fuse alarm, with the ingenious non-dismantling of the wire measurement signal current technology, the measurement of signal current as long as the ammeter pen is inserted into the test hole, the whole measurement process equipment is uninterrupted, does not affect the normal measurement and control process, provides great convenience for maintenance work.

7. Quick assembly: Using the special installation backplate with standard module holes designed by the company, you can put aside the drilling tool and only need a screwdriver to complete the installation of electrical components in the cabinet.

VGA analog signal display port such as a monitor.

com serial communication port such as used to configure switches.

PS2 mouse and keyboard interface.

The VGA is the same as the COM interface.

PS2 is the same as the S terminal.

There is no such high-end goods in China, the D terminal is purely digital, there are too many differences, and the D terminal is the Japanese version.

Sony's TV has this, and it seems to sell 49999

If your connector is used in electrical circuits or electrical circuits, it is an electronic component. As an electronic component, the connector has electrical requirements, such as dielectric strength, creepage distance, current and voltage, and some can be soldered.

The terminal is an electronic component, which is a component of electronic components and small machines and instruments, which is often composed of several parts and can be used in similar products; It is often referred to some parts of the electrical, radio, instrument and other industries, such as capacitors, transistors, hairsprings, clocksprings and other sub-devices. If you want to test the connector, you can choose the blade pin, which can ensure the stability of the test.