What parts do you need to replace for the Audi A6l 2 4 engine pull cylinder

If during the warranty period, go directly to the claim procedure and throw the car to 4s.

After confirming that it is a cylinder puller.

They're in charge of changing the powertrain, which is just getting the engine new.

Audi pays for quality issues that don't cost money.

Don't play if you hold the tile, first find the reason, is it a lack of water, or a quality problem, pull the cylinder, the main cylinder barrel, piston, piston ring, crankshaft, tile, and then look at the valve

It's Audi again, you're a few years old, have you passed the warranty period? If not, throw the car to the 4S shop as said on the first floor. If you need to change the engine, 4S will be responsible for numbering you, or your original engine number. It's just that.

It is not necessary to extend the warranty period with a new machine.

The price of an Audi A6L engine generally ranges from tens of thousands to hundreds of thousands, and the engine is a machine that can convert other forms of energy into mechanical energy, including internal combustion engines, external combustion engines, electric motors, etc.

The precautions for replacing the engine of the car are as follows:

1. Replace the engine first of all pay attention to the relevant procedures of the engine, whether there is the corresponding certificate, whether the packaging is complete, whether the wooden box of the packaging is clearly marked, in principle, the replacement of the engine is to the vehicle management office for change, the engine number should be the new number, the general number is mainly due to the engine does not have a certificate or to avoid the cumbersome procedures of the change, but this is not allowed, if the car inspection is found, will not be able to carry out the inspection.

After replacement, check whether the engine wiring harness and pipes are messy, and the run-in can be in accordance with the new car run-in standards.

2. Under normal circumstances, the staff of the 4S shop need to help you change the new engine number on the driving license to replace the engine. When replacing the engine, be sure to check the certificate of conformity and, if possible, identify whether the engine is new.

3. The "Measures of the People's Republic of China for the Registration of Motor Vehicles" stipulates that the engine of a motor vehicle cannot be changed at will. The engine that has not been replaced without regulations has not been strictly tested or is itself a scrapped machine, the safety performance is greatly reduced, and the potential safety hazards increase.

The engine replacement is high, what is the problem with the engine, you can find someone who specializes in repairing Audi engines to see, you can save a lot of money, Beijing call me.

The price of a Sutar engine is 30,000, the price of the Magotan engine is 10,000, in view of the same technology as the Audi A6L engine, the price should be around 40,000, the same model displacement is different, the engine price will be different, the ideal price of the engine should be 50,000, 60,000, 80,000.

Friend, what is the engine displacement? The displacement is not the same**much worse Oh if you need **, please explain again.

And why do you have to change the engine?

Can't be repaired?

There's no mistake upstairs.

Volkswagen 4S and Audi 4S are in the same class?

That's not how it works.

Changing the engine? Don't bother with that, just buy a new one.

Changing the engine is not much different from buying a new car.

To disassemble and assemble the engine, Audi needs to disassemble the chassis parts first, then disassemble the engine and transmission wiring harness, drain the oil-water coolant, and finally put down the engine and gearbox directly.

Precautions when disassembling the engine: The disassembled parts, especially when disassembling the engine, must be cleaned in the order of disassembly and placed in clean plates separately so that they can work accurately and quickly during assembly. (2) The machined surface that is easy to rust should be coated with lubricating oil in time.

If the disassembled parts need to be stored for a long time, the packaging should be sealed with a small amount of grease to prevent the parts from rusting. It is forbidden to use metal tools such as hammers to directly percussion processing containing calling surfaces and matching parts. If necessary, tap with a rubber hammer.

Precautions when assembling the engine: Before the engine is assembled, all parts and components should be cleaned. All kinds of repaired parts must be inspected and qualified according to the technical requirements of the mu before they can be assembled.

When installing crankcase bearings, heat the area around the crankcase bearing bore with a heater. Before assembly, the surface of all matching parts should be properly lubricated. All kinds of snap rings, retaining rings, and sealing rings should be strictly inspected before assembly, and those that are defective, deformed, and lose elasticity should be replaced.

Millions of car purchase subsidies.

Prepare the tools needed for dismantling, change the taper to a hand, a T-20 spline, a T-30 spline, and then enter the process of dismantling. Take out the slotted cone cluster rent, first remove the control panel with seepage with the trillion wiring harness, and gently pry from the edge part of the control panel and the door trim panel with the slotted cone cone.

X Bao buys it recommended to buy from the BMW 5 Series even if the lamp is broken. Even the 5 series lamps and buy postage points to do the general seller sells its own broken lamp scrap, the seller keeps it useless, Hella 4 is dismantled from Mitsubishi Wing God, Hella 3 solenoid valve stop Hella logo is concave and convex.

Performance Configuration:

With the continuous development of shock absorption technology, the longitudinal vibration damping performance of today's high-end models has reached a very high level. As a result, more and more attention is being paid to the vibration comfort of the whole vehicle, which is largely determined by the design of the front and rear axles as well as the frame assembly, and the new Audi A6L has focused on this aspect of the development of vibration comfort.

The all-new Audi A6L features a five-link front suspension that combines the rigid connection necessary for sportiness and comfort with low static base stiffness. Among them, the frame shock absorbing support in the form of hydraulic can significantly improve the driving comfort of the vehicle, and effectively reduce the impact and frustration when passing through speed bumps and uneven road surfaces, thereby reducing the impact on the lumbar spine.

Changing the crankshaft oil seal does not need to lift the engine, as long as the engine timing chain or belt shell is removed, and the oil seal needs to be removed after changing the crankshaft, which does not affect the use. Precautions for replacing the crankshaft oil seal: Before installing the oil seal, be sure to wipe the crankshaft flange surface and the oil seal safety and assembly holes with cleaning solution or a cotton cloth dipped in soapy water, and then wipe it with a dry cotton hand-dressed transport cloth; If the cleaning liquid and oil in the oil seal hole are not wiped clean and the oil seal is assembled, it will cause the second oil leakage of the oil seal; Before installation, it is necessary to check whether the oil seal spring is installed in place, and the main lip is flanged and scratched.

Introduction to crankshaft oil seal: crankshaft beam oil seal is a mechanical component used to seal grease (oil is a common liquid substance in the transmission system, and also refers to the meaning of general liquid substance), which isolates the parts that need to be lubricated in the transmission parts from the output parts, so as not to let the lubricating oil leak.

Summary. Hello, happy to answer your <>

After the Audi engine is replaced, the oil seal must lift the engine. The first thing to do is to lift the engine, remove the oil pan, and turn the engine upside down. The crankshaft oil seal is two semicircles together, and the crankshaft must be removed to replace the rear oil seal.

Just put it back in the same way as it was new. Therefore, the oil seal must lift the engine after the Audi engine is replaced.

Does the oil seal have to lift the engine after an Audi engine is replaced?

Hello, happy to answer your <>

The Audi engine is even hungrier, and the oil seal must be lifted after the change. The first thing to do is to lift the engine, remove the oil pan, and turn the engine upside down. The crankshaft oil seal is two semi-circles that are disassembled together, and the crankshaft must be removed to replace the rear oil seal.

Just put it back in the same way as it was new. Therefore, the oil seal must lift the engine after the replacement of the Audi engine.

Kiss <>

Expansion: The automobile engine is the device that provides power for the car, is the heart of the car, and determines the power, economy, stability and environmental protection of the car. According to the different powers, automobile engines can be divided into diesel hail engines, gasoline engines, electric vehicle motors and hybrids.

The engine is the power source of the car. Most of the automobile engines are thermal power units, referred to as the lead state of the thermal engine.