Whether the two buildings can be connected to the wireless network, and how to use one broadband wir

The connection distance of a wireless AP or wireless router is generally about 100-300 meters.

Just buy a D-Link wireless router.

But you're 200 meters away, and you're in two buildings.

Maybe the signal is relatively small, I guess it will be very slow after connecting it, and the probability of a successful connection is also very small.

Specific connection: cat + wireless routing.

Requirements: Both computers must have wireless network cards.

Here's a ** for you.

You look at which wireless router has the transmission distance** which.

I don't recommend going wireless, though.

Because you're between two buildings, after all, and there's a few walls between them.

It will affect the signal very much.

If you want to get good transmission efficiency, then you can only spend a lot of money, then it's not worth it, you might as well pull the cable.

The effective distance of the wifi is very limited, and the attenuation is very fast, if there is a building in the middle, the attenuation is faster 50m is already very good.

You can use two wireless repeaters, but the distance of 200m is too far, I don't think optimistic, and the energy density required to penetrate the space of 200m is more than 1W, which is not necessarily a good thing for people.

You can go to **Find a wireless signal amplifier to try it.

There's always a way, and if you can't pull a cable or fiber from your home to your mother's house, you need to look at the way you use wireless, you can use directional antennas to enhance the wireless signal.

First of all, the network speed of two buildings with one broadband may be very slow, and you need to pull a light drill.

Secondly, with wireless Internet access, then you have to do wireless coverage engineering.

If you do these two things well, then you can do it.

Don't do it, it can't be realized, the only way is to pull the network cable, there is no other way.

Self-routing cables, your home leads to your mother's house.

If Wi-Fi can be on the first floor and can not be used on the second floor, it means that Wi-Fi penetration is poor, you can buy a better browser.

If the signal on the first floor and the second floor is not good, you can place the router between the first floor and the second floor, and there is an open and unobstructed place, and you can also buy a powerful router and wireless network signal repeater with better effect. Move the route location left and right, and go to the route settings page to change the signal strength to 100%.

You say that, it means that you are rubbing other people's wifi, right? Hee-hee, wifi can be set to the coverage area.

Just set it up according to the wireless bridging method.

How to set up the wireless bridging mode of the wireless router:

1. Confirm the main wireless routing parameters.

Confirm the wireless signal name, wireless encryption method, wireless password, and wireless channel of the primary router.

Note: Before setting up, the wireless channel of the main router needs to be fixed.

2. Set up the secondary router.

1. Modify the wireless parameters and turn on the WDS scan signal.

Connect the computer to the sub-router, log in to the management interface, click Wireless Settings >> Wireless Basic Settings, modify the SSID number to be the same as the main router, fix the channel, check to enable WDS, and click Scan.

2. Select the main router signal.

Find the SSID of the primary router in the scan page and click Connect.

Note: If the WDS cannot scan the signal of the primary router, make sure that the wireless function is enabled on the primary router, and try to reduce the distance between the primary and secondary routers.

3. Select the encryption method and enter the wireless password.

Key Type Select the encryption method of the main router, enter the wireless password of the main router in the Key field, and click Save after entering. You don't need to restart your router and proceed to the next step of setup.

4. Set the wireless password of the secondary router.

Click Wireless Settings >> Wireless Security Settings, select WPA-PSK WPA2-PSK, set the same wireless password as the main router in PSK Password, and click Save. When the system prompts "You have changed the wireless settings, it will take effect after restarting", click Restart, and when the restart prompt page pops up, click OK and wait for the restart to complete.

1: Please confirm the wireless router first.

Check whether the configuration is correct.

Check whether the IP address is obtained for the WAN port

2: If the WAN port does not get the IP of the Chinese companion oak, then please plug the network cable directly into the cat broadband dial to see if you can dial it.

3: If you can dial directly to the cat, only the router cannot dial. Chaos Hall.

Then it is generally a router hardware failure.

4: If you can go to wifi, you can't go on it suddenly.

Then it is related to the router cache, it is recommended that the user dial the power cord behind the router and plug it in, sell it and wait until the signal indicator lights up again, and then try to connect the mobile phone or computer.