Deceleration oscillation reticle, using hot melt paint, thickness 2mm set of what quota

If the fluid characteristics of the original marking coating are improved, the coating has excellent thixotropic properties in the molten state. By shortening its drying time and improving the compressive strength and softening point, etc., and using special special construction tools to regularly draw out various protruding pattern markings such as point shapes, bars, squares and so on on the surface of the marking, the finished markings have the function of vibration after the automobile crimping. Land Rover Traffic has the production of marking paints, which have a large inventory and the effect is not bad.

Oscillating marking coating is to modify the coating on the basis of hot melt road marking coating by shortening its drying.

Knot time and improve compressive strength and softening point, etc., and use special special construction tools to draw point shapes, bar shapes.

and other convex pattern markings, these convex parts should have enough compressive strength when cooled down in order to be able to bear.

Crushed by a vehicle.

When a speeding vehicle is crushed on such a marking, a low "boom" sound will be produced, which is more pronounced.

The sound of crushing on the road nails should be softer, so as to remind the driver that the car has been lowered and the driver is right.

The machine has a strong warning and reminder effect. In addition, on rainy days especially on rainy nights, due to the raised reticle sections.

The gap between them can form a drainage area, and the raised part of the marking line will always protrude from the water surface to ensure that the marking line is not rained.

Completely submerged, therefore, the oscillation marking is also known as the raised marking, noise marking, rainy night marking. That is to say, the class of mark.

Lines can provide all-weather visibility, especially on rainy nights with the incomparable advantages of any marking, often installed.

In special places on the road, such as: turns, pedestrian crossings, intersections, etc.

Reflective hot-melt marking coating contains 20% internal mixing beads, vibrating hot-melt marking coating contains 20% microbeads, and enhanced reflective marking coating contains 25% internal mixing beads, which is generally applicable to highways, municipal roads, national highways, etc.

Land Rover Transport is a manufacturer of hot melt marking coatings.

1) There is no specific setting specification for vibrating marking so far, 2) the color refers to T280 hot melt marking coating (protruding type), 3) there is no standard for protruding spacing and protruding block shape, all of which are set according to the knife edge shape (transversely arranged and fixed) of the current marking equipment, and the longitudinal spacing of the protruding block is generally between 10 and 20cm.

4) The thickness of the base and the thickness of the protrusion are specified in 16311, and the thickness of the protrusion is 3 5mm5) The color is mainly white and yellow, and the color coordinates are specified in white, blue, yellow and other colors 6) To put it in the vernacular, what shape is set into, it is your design that has the final say7) Width, the maximum width of the current market vibration marking equipment is generally 30cm wide, and 45cm is generally spelled out with 15cm.

8) The color deceleration line should be mostly hot-melt anti-skid marking line (or cold-painted color anti-slip), refer to the standard JT T712

9) Vibration protrusion type is commonly used.

Hot-melt marking coating is currently one of the most marked coatings used in China's traffic roads, from this year's 315 CCTV party to blow up the road marking in some cities in China since the unqualified, hot-melt marking paint manufacturers pay more and more attention to the quality of coatings, according to the national standard ingredients should be about 30 to 35 yuan a square, thickness; One ton of hot-melt marking paint can generally be applied about 200 to 220 square meters.

In fact, it mainly depends on the amount of a line on your side, if it is relatively small, not much, you can choose the local construction team to contract labor and materials, the road surface is in good condition, ** is about 4-6 yuan a meter (line width 15 cm, thickness in, does not include the class fee in it. If you go by square meter, it is about 30 yuan per square meter.

If there are more, the amount of work is very large and the requirements are very high. It is recommended that you find a manufacturer specializing in hot melt coatings, purchase coatings, and then find someone in the local area to contract labor and materials for you to do marking. The cost will be much lower.

Land Rover Transportation has a hot melt marking coating in the production of hot melt marking coatings, which can be supplied in batches throughout the country.

This is based on the quantity and quantity, as well as the local price and consumption level. Under normal circumstances, the amount is low, and the marking construction team is contracted labor and materials, and there is no additional cost. There are also parking spaces that are only counted by the number, and the passages can be calculated by square or meters, and arrows and paintings are counted by the number.

You may be asking how much is a meter of hot melt construction! There are basically two commonly used road markings, one is cold spray, the ** of one meter of road marking paint is about 3-6 pieces, and the ** of one meter of hot melt is about 5-8 pieces, depending on the number and construction difficulty! There are also two-component reticulators, and **reticulators, which are not commonly used, and the smaller the number, the more expensive!

Suzhou Fengjingyuan Transportation will serve you wholeheartedly!

The market of this product is not expensive, more than a few thousand yuan a ton. In general, its ** is related to its manufacturer, that is, the different places of origin. In addition, when buying it, you should pay attention to the cost of its freight, that is, the distance, whether the freight is included, and how the shipping cost is calculated.

1. Manufacturers and brands: Due to the different quality of the products produced by each manufacturer and the different reputation, the quality of the products is different, and some big brand products have good quality assurance, which is relatively higher. It's about 3,500 yuan a ton.

Sanace marking line construction for 20 years, has rich construction experience.

How many materials do you need for three kilometers and fifteen centimeters.

The unit of raw materials is tons. How to say that it is a square meter、

There is a corresponding quota in the municipal engineering quota, and the number of projects and the design have basically been given.

1.The demarcation solid line (dashed line) is calculated by length (m), (paint points: cold paint, warm paint, hot melt paint);

2.Motorway and non-motorway ground text marks are counted by one (3m, 6m, 9m high, paint: cold paint, warm paint, hot melt paint);

3.The guiding arrows of motorized lanes and non-motorized lanes are also counted by one (divided into several kinds of heights of 3m, 6m and 9m, and paints are divided into: cold paint, warm paint, and hot melt paint);

4.The bar line is calculated by square meters (paint points: cold paint, warm paint, hot melt paint).

You can check the quota description of the relevant chapters of the local municipal engineering quota.

Thick polyurethane waterproofing coatings should be applied to the construction project budget quota.

The construction project budget quota 94 standard can be found in the roofing project quota sub-project coating film waterproofing, and apply A7-193 and A7-195 polyurethane waterproof coating quotas.

The 03 version of the construction project budget quota is applied to the 7-49 polyurethane waterproof layer quota, and the thickness is converted according to the design requirements.

Apply A7-193 and A7-195 polyurethane waterproof coatings. View the original post