Installation requirements for electronic fence system, electronic fence installation and commissioni

Electronic fence installation:First, assemble the terminal rod, load-bearing rod and intermediate rod respectively; Then select the corresponding position on the wall to drill the hole, and fix the three rods separately; Finally, hang the alloy wire, install the host, and power on and debug.

Electronic fence installation:

Electronic fence installation requirements:

1) The base installation should be firm and horizontal, and try to maintain a straight line between the front and rear bases.

2) The base is installed and fixed, using stainless steel expansion bolts or ordinary expansion bolts, and stainless steel bolts are preferred for rust prevention and long-term use. The terminal rod base is made of 8mm bolts, and the middle rod base is made of 6mm bolts.

3) The fence wires should be kept parallel and equidistant from each other, which should be 200mm 20mm.

4) Keep a vertical line between the top and bottom of the fence tightener.

6) When arranging PVC pipes, be sure to ensure that there are joints between pipes and pipes, and use V-PVC special adhesive to bond firmly. Party A should be communicated to confirm the use of pipes along the edge of the corner or underground. When the underground pipe needs to be excavated, it should be kept at a certain depth (about 40cm).

7) When arranging the line, it is necessary to ensure that a line goes to the end, and the joint situation is strictly avoided in the middle; Especially when underground pipes, it should be resolutely eliminated. When buying cables, if the length is not enough, you should customize the cable in advance.

8) When installing the arrester, the ground pile must be driven below the ground. The ground resistance should be less than 10. The arrester should be installed at the beginning of the electronic fence, i.e. near the end of the remote control.

The upper end of the arrester is connected to the highest high-voltage wire on the electronic fence, the lower end of the arrester is grounded, the upper lead uses high-voltage insulated wire, and the lower lead wire should be reliably grounded.

9) A warning sign should be hung between the wall piers (10m) to fully remind the warning.

Attached to the fence, the attached electronic fence is mainly used in occasions with high safety requirements and does not occupy the surrounding land. There are three requirements for the existing fence. First, the fence should have sufficient fastness to withstand the tension and pressure of the electronic fence.

Second, the height of the fence should not be less than 2m. Third, the mesh of the fence must be less than 50mm, so as not to reach into the electronic fence attached to the inner side of the wall. Wall-top electronic fences, which are more popular in China, are erected above or on the side of the top of existing fences.

It can be installed vertically or at an angle. The height of the electronic fence is about the same.

1. System check.

When the pulse electronic fence alarm system is fully installed, a comprehensive inspection should be carried out. Check whether the load-bearing column is firmly installed, whether the position is appropriate, whether the position of the insulator is correct, whether the grounding resistance of the wire meets the requirements, whether the connection of the high-voltage insulated wire is correct, whether there is a blind area, etc.

2. The system is energized.

When the power cord of the pulse controller host is connected, you can see that the power indicator is on and the pulse signal is "clicking" every second; The alarm indicator light is not lit, and the internal alarm horn does not sound; If the arming light is not on, it means that the system is in the state of disarming, and there should be no "click" sound of the pulse signal at this time, indicating that the system is operating normally.

Short circuit test of electronic fence system.

3. Electronic fence alarm test.

1) Open circuit test.

Remove any high-voltage insulated wire in the electronic fence host in the measured defense area to form an open circuit, then the alarm indicator light of the pulse electronic fence host will be lit, and the corresponding sound and light alarm will be started. The alarm management equipment in the monitoring room emits an alarm sound to indicate the specific alarm defense area and a series of functions are realized.

2) Short circuit test.

With a high-voltage insulated wire with bare wires at both ends lapped on any adjacent 2 alloy wires, the alarm indicator light of the electronic fence host is lit, the sound and light alarm light of the corresponding defense area is activated, and the alarm management equipment in the monitoring room sends out an alarm sound to indicate the specific alarm defense area and a series of functions are realized.

When the front end of the electronic fence is installed, it should be installed according to the changes of different physical prevention carriers of the perimeter, and the installation methods of the front end fence are different, and the common installation methods can be divided into: auxiliary installation, wall top installation, independent installation and floor installation.

Attached Installation:

Wall top installation:

It is generally used when only the top of the fence or iron fence needs to be guarded, and the front end support rod is fixed to the top of the fence (or the outside or inside of the top of the wall). It is recommended that the height of the fence wall should be above, as shown in the figure below

Stand-alone installation Floor-mounted installation.

When there is no solid fence or fence at the front end of the fence, the fence support rod can be directly fixed on the ground, and the height of the independent installation fence should be 2m according to the requirements of the national standard.

In order to make the support rod can withstand sufficient tension, it is recommended that the support rod is embedded in the ground depth, if the soil is soft, it is strongly recommended to fix the support rod by pouring concrete, and use diagonal brace support or pull wire reinforcement, as shown in the following figure:

Electronic fence floor mounting.