How to install the electronic fence in the factory, how to install the electronic fence

Factory electronic fence installation process:First, assemble the terminal rod, load-bearing rod and intermediate rod respectively; Then select the corresponding position on the wall to drill the hole, and fix the three rods separately; Finally, hang the alloy wire, install the host, and power on and debug.

Factory Electronic Fence Installation Details:

1) The base installation should be firm and horizontal, and try to maintain a straight line between the front and rear bases.

2) The base is installed and fixed, using stainless steel expansion bolts or ordinary expansion bolts, and stainless steel bolts are preferred for rust prevention and long-term use. The terminal rod base is made of 8mm bolts, and the middle rod base is made of 6mm bolts.

3) The fence wires should be kept parallel and equidistant from each other, which should be 200mm 20mm.

Factory electronic fence installation site.

4) Keep a vertical line between the top and bottom of the fence tightener.

6) When arranging PVC pipes, be sure to ensure that there are joints between pipes and pipes, and use V-PVC special adhesive to bond firmly. Party A should be communicated to confirm the use of pipes along the edge of the corner or underground. When the underground pipe needs to be excavated, it should be kept at a certain depth (about 40cm).

7) When arranging the line, it is necessary to ensure that a line goes to the end, and the joint situation is strictly avoided in the middle; Especially when underground pipes, it should be resolutely eliminated. When buying cables, if the length is not enough, you should customize the cable in advance.

8) When installing the arrester, the ground pile must be driven below the ground. The ground resistance should be less than 10. The arrester should be installed at the beginning of the electronic fence, i.e. near the end of the remote control.

The upper end of the arrester is connected to the highest high-voltage wire on the electronic fence, the lower end of the arrester is grounded, the upper lead uses high-voltage insulated wire, and the lower lead wire should be reliably grounded.

9) A warning sign should be hung between the wall piers (10m) to fully remind the warning.

10) 485 bus specifications: RVS RVV four-core, or, waterproof.

The installation of electronic fences in factories is now the most advanced perimeter anti-theft product.

Shanghai Suomai Electronic Technology --- professional factory electronic fence installation.

Factory electronic fence design.

Factory electronic fence**.

Welcome to call Shanghai Suomai Electronics to provide you with detailed factory electronic fence solutions!

Shenzhen Jinsheng Tongda Technology Co., Ltd. is one of the leading professional electronic fence companies in China, and is a new enterprise specializing in intelligent perimeter alarm systems composed of R&D, production, sales, customer service and marketing departments. The company has always taken "continuously improving customer satisfaction" as the goal pursued by the enterprise, and won the support of customers with integrity to achieve faster and more lasting development.

"Electronic fence" is the abbreviation of intelligent perimeter security blocking alarm system, which introduces the latest security concept of "blocking first, alarm secondary". Compared with the existing perimeter security products, the electronic fence has more advantages: generally speaking, the infrared radiation can not block the foreign invaders, and the high-voltage power grid can play a blocking role, but due to the strong alternating current can lead to the death of people, very dangerous, and the electronic fence in the blocking role at the same time, no harm to the human body, truly "blocking, alarm supplemented".

At the same time, the electronic fence has a very low false alarm rate compared with infrared radiation, and its installation and debugging are convenient, high reliability, and at the same time play the role of alarm, it is more deterrent than infrared radiation. In addition, the electronic fence is obviously a better choice than the existing perimeter security products from the comprehensive factors such as installation, commissioning, maintenance, and service life.

With its unique performance, electronic fence is widely used in substations, power plants, institutions, industrial and mining areas, industrial and mining enterprises, material warehouses, residential quarters, villa areas, schools, airports, water plants, aquaculture and animal husbandry sites, key cultural relics sites, military facilities, prisons, detention centers and other places with walls and need walls.

After the installation of the front end support rod of the electronic fence is completed, the wiring construction work of the alloy wire will begin. The alloy wire is usually 100 m disc and 400 m tray, and the 400 disc is preferentially used when the defense zone is long, which may reduce the joint of the alloy wire.

Renderings of electronic fence installation.

When the alloy wire is tightened, the tension of each parallel alloy wire is basically the same, and the tightening force is best to keep the alloy wire parallel and straight, but retain a certain margin of contraction.

When the front end of the electronic fence is installed, it should be installed according to the changes of different physical prevention carriers of the perimeter, and the installation methods of the front end fence are different, and the common installation methods can be divided into: auxiliary installation, wall top installation, independent installation and floor installation.

Attached Installation:

Wall top installation:

It is generally used when only the top of the fence or iron fence needs to be guarded, and the front end support rod is fixed to the top of the fence (or the outside or inside of the top of the wall). It is recommended that the height of the fence wall should be above, as shown in the figure below

Stand-alone installation Floor-mounted installation.

When there is no solid fence or fence at the front end of the fence, the fence support rod can be directly fixed on the ground, and the height of the independent installation fence should be 2m according to the requirements of the national standard.

In order to make the support rod can withstand sufficient tension, it is recommended that the support rod is embedded in the ground depth, if the soil is soft, it is strongly recommended to fix the support rod by pouring concrete, and use diagonal brace support or pull wire reinforcement, as shown in the following figure:

Electronic fence floor mounting.