How can a novice pull an erhu without noise Thank you

I learned erhu, because I also live in the community, so I used to be troubled by this matter, I want to practice professionally at night, but I am afraid of disturbing others

Later, the teacher gave me a suggestion

First, prepare a piece of paper and a pencil, which should be at least the width of an erhu barrel and a little tape

Roll the paper on the pencil, roll it firmly, preferably without gaps, and fix it with tape.

Then place the pencil above the horse and hold it between the barrel and the strings

This way, not to mention that you're upstairs and downstairs, even if you're in their house, as long as the door of the room where he practiced is closed, it's basically inaudible

And this method also helps with the control of the bow

That's how I practice at night

If you want to be ruthless, treat him. If you're a kid or you have a kid buy a roller skate and let the kid skate in the house except for the downstairs of your house and the rest is basically unaffected or buy a glass ball and bounce it on the ground a few times when it's okay don't pick it up and wait for the ball to stop moving and start over again The sound... It's really uncomfortable.

Hand hitting: I hope oh

This is mainly a matter of the method of transporting the bow, the arm is relaxed, the big arm runs naturally with the small arm, and the friction between the bow hair and the string is reduced to a minimum.

Pull your right hand slowly, try to be as steady as possible, and it will get better slowly

Practice longbowing often, carry from bow to tail, stay relaxed, and put force on the bow.

Practice more, carry a longbow, big arm with small arm, small arm with wrist.

Enthusiastic netizens" method is easy to use!

Summary. The surface of a new erhu bow is very clean and smooth, pay attention when holding it in your hand, try not to scratch or touch the bow hair with your hands, especially those with sweaty or stained hands. When wiping rosin, it should be even and in moderation.

Why can't the newly bought erhu be installed but can't pull out the sound?

Hello, it's a pleasure to serve you, dear, wait a minute, Ha, inquiring, thank you very much <>

Dear, the newly bought erhu can't make a sound, because the erhu bow hair is not rubbed with rosin, if there is too little rosin, the erhu can't make a sound.

The rosin is also rubbed evenly, but it can't pull out the sound, what's going on! Newly bought erhu.

2.Scratch back and forth on the surface of the new rosin, roughening the surface so that the rosin powder can effectively adhere to the surface of the bow hairs when rubbing the rosin. 3.

The surface of a new erhu bow is very clean and smooth, pay attention when holding it in your hand, try not to scratch or touch the bow hair with your hands, especially those with sweaty or stained hands. When wiping rosin, it should be even and in moderation.

It's all wiped off. Shaya's voice.

Wipe them evenly.

Dear, the sound of Shaya may be a python skin tight, not yet opened. The second reason is that the force is insufficient to press the solid strings to make it vibrate perfectly with the python skin.

Dear, it is recommended that you also consult the store where you purchased it.

After rubbing it for a long time, the bow hair has become milky white.

Good. <>

If there is too little rosin, the erhu will not make a sound, so it is recommended that users rub their feet with rosin.

The bow hairs rub the rosin, and the bow hairs will have a certain friction with the strings, making the strings vibrate, and the greater the amplitude of the strings, the greater the sound. Rub rosin evenly on both sides, too much is easy to make noise, too little is not enough to make sound. And don't easily touch the erhu bow with your hands, don't touch it with your hands, the strings may be stained with sweat, etc., and you won't be able to pull out the sound.

Incorrect way of holding the bow can also cause the erhu to not sound. If the bow is held incorrectly when pulling the erhu, it will not exert enough force to pull the inside and outside, and the ideal sound effect will not be achieved.

My newly bought erhu still doesn't make a sound after rubbing the rosin, what's going on?

The rosin should be rubbed along the bow, and the end can be wiped by fixing it in one place, rubbing more, the bow should be in the middle of the two strings, and the wood part should be on the outside of the thin string. Maybe it's not wrong, it's the rosin's problem, and it is recommended to see if the Rafa of the manga has a bow there is right. Thank you.

The inner chord of the erhu should be inside, the outer chord should be outside, and the bow should be above"Long hair"It should be sandwiched between two strings, and when you pull hard, you pull the inner string, and when you push harder, you pull the outer string. The rosin needs to be ground into a powder and then rubbed on top of the bow"Long hair"on, directly wipe particularly slowly. There is also the need to tighten the strings slightly, otherwise it will not sound if it is too loose.

A string pillow should be installed on the snakeskin eardrum below, and two strings should be placed on it to drive the eardrum to vibrate to achieve the effect of amplifying the sound.

Try it again.

Summary. One is a bow made of nylon wire. This kind of bow cannot replace the bow made of a horsetail, and if you buy such a bow, it will definitely not be able to sound, so it is recommended that you change it.

Second, if it is a bow made of horsetail, it is not rubbed with rosin. Many beginners who play stringed instruments do not pay attention to this problem, and the newly bought bow will not be able to pull the sound if they are directly installed and pulled. The bow hairs do not rub the rosin, there is no friction on the strings, and the strings do not make sounds.

The top of the horsetail is not smooth, and the top of the horsetail is uneven and uneven with a microscope, and when rubbed with rosin, it becomes sticky, so that it can rub against the strings and make sounds.

Why can't the newly bought erhu be installed but can't pull out the sound?

One is a bow made of nylon wire. This kind of bow cannot replace the bow made of a horsetail, and if you buy such a bow, it will definitely not be able to sound, so it is recommended that you change it. Second, if it is a bow made of horsetail, it is not rubbed with rosin.

Many beginners who learn to play stringed instruments do not pay attention to this problem of Zhenchun, and the newly bought bow will not be able to pull the sound if it is directly installed. The bow hair does not rub the rosin, there is no friction on the strings, and the strings will not make a sound. The top of the horsetail is not smooth, and the top of the horsetail is uneven and uneven with a microscope.

The bow hairs of the newly purchased bow should be cleaned and smoothed. Because there is grease on the surface of the horsetail, it can't be rubbed with rosin. Use an alkali ruler to disperse water (baking soda water is also fine), wash the bow hairs of the letter sleepy general, rinse them with clean water, and dry them.

The bow bought by the new only skin is not easy to rub rosin, I have a trick to share with you, rub the rosin on the newly bought bow, don't wipe the whole bow, take off the bow first, start from the root of the bow, rub it repeatedly at 5 cm, rub the 5 cm and then extend 5 cm to continue to rub, in this way to wipe the whole bow (the bow should be wiped inside and outside), it is very effective. After wiping it for the first time, the next time you wipe it, just wipe it twice, erhu is not better than banhu, usually rosin should not be rubbed too much, too much will also produce noise, and unhygienic.

In addition, if it still doesn't sound, check the erhu itself, whether there are any problems with the saddle, strings, python skin, etc. The newly bought erhu is like our newly bought car, which needs a run-in period (I heard that the current new car does not need to be run-in), and I can't find the feeling when I just pull, and I can only adapt to it after a while, and the more I pull, the better it is, the color is getting brighter and brighter, and the good erhu is pulled out. Li Sou.

Summary. Hello dear and happy to answer your <>

The newly bought erhu is installed but the reasons why it can't pull out the sound are as follows: 1. A bow made of nylon wire. This kind of bow cannot replace the bow made of a horsetail, and if you buy such a bow, it will definitely not be able to pull it, so it is recommended to change it.

2. The bow made of horsetail is not rubbed with rosin. The newly bought bow is directly loaded and pulled, and it will definitely not be able to pull out the sound.

Why can't the newly bought erhu be installed but can't pull out the sound?

Hello dear and happy to answer your <>

The newly bought erhu is installed, but the reason why it can't pull out the sound is as follows: 1. A bow made of nylon wire. This kind of bow cannot replace the bow made of a horsetail, and if you buy such a bow, it will definitely not be able to sound, so it is recommended to change it.

2. The bow made of horsetail is not rubbed with rosin. The newly bought bow is directly loaded and pulled, and it will definitely not be able to pull out the sound.

Kiss to expand the file: The method of learning erhu is as follows: 1. Erhu Mu Fool Feng is a very difficult instrument to learn among stringed instruments, and you need to be patient and calm your mind when learning erhu.

2. Through many exercises, train the sensitivity of the ears, and quickly achieve the accuracy of distinguishing the pitch to cultivate their own musicality.