Why is Binger watches going faster and faster?

At the beginning of June, I just bought a Tissot mechanical watch in 100 miles, and the watch has been going fast for 8 minutes since I put it on.

Mechanical watches have a power reserve, and generally they will go a little faster when they are worn, and they will go a little slower when they put their heads down. There is no need to worry, unless it is becoming more and more inaccurate over time, which may be due to magnetism affecting the stability of the movement. But it's usually fine.

Mechanical watches are not completely accurate, and it is normal for the daily error to be between 5 and 15 seconds. Especially for the watch you just bought, the error will be unstable, and you need to wear it for a period of time and then observe.

Tissot watches were ok. As long as the error is not too large, it is normal within 15 seconds. After wearing it for a long time, you will gradually get used to this error.

Maybe it's a little bit of a problem.。。 You can take it and fix it.

The watch is not allowed to run inaccurately:

1.Watch magnetization: The watch is in too much contact with items with magnetic fields, which leads to the phenomenon of magnetization of the watch, causing the watch to be inaccurate.

After being magnetized, the watch may stop, slow, or fast. After the watch is magnetized, its magnetism will not recede on its own, and it needs to be demagnetized and repaired to return to normal.

2.Lack of maintenance: If the watch lacks maintenance, it will lead to wear and tear of parts, dry up the sludge, affect the normal running time of the watch, and make the watch appear fast and slow.

3.Mechanical failures: Mechanical failures such as watch balance spring failures, escapement failures, and component slips can cause the watch to be fast and slow.

Mechanical watches are sometimes fast and sometimes slow, and it may be caused by severe impacts, water ingress, etc. Quartz watches are generally very accurate and less prone to time failures. In the case of adequate maintenance, it is more likely to be fast and slow, which is more related to the failure of the circuit board, or the poor contact of a certain part.

Generally, it is caused by the lack of power of the watch, or it may be the reason for the magnetization of the watch, you only need to time the full wind to ensure that the watch has sufficient kinetic energy, or go to the watch store to demagnetize.

If your watch has been bumped, it may also be caused by the speed clip offset of the watch, and the after-sales correction of the speed clip is required.

Binger, the pioneer of Switzerland's first disposable wristwatch!

Haven't you heard that seeing the time is the least important function of a watch?

Come to me tomorrow to repair it, and bring it for a day! That's 24 hours.

Never really owned, just kept for the watchmaker...

For accusatives, errors, everything is possible.

Errors of less than three hours a day are normal.

It is normal for a mechanical watch to have an error, and if it has been stable at -3, there is no problem. The one-day error of high-quality products is -30+45 seconds; The first-class product has an error of -40+75 seconds a day. Mechanical watches have a mechanism for setting the time on the pendulum hairspring, which can be adjusted by itself.

Moreover, mechanical watches also have a run-in period, which can only be stable after a period of wear, while low-end mechanical watches may have the above phenomenon in about a year, so it is recommended to buy a higher-end mechanical watch.

The watch is getting slower and slower, and it may be that the watch battery is running slower and slower.

Solution: Replace the service point after the sale, if the fruit is a new watch that has not been bought for more than a year, it may have been in contact with some magnetic objects.

Solution: Minimize the size of objects with magnetism.

The handling of the magnetization of the watch is very simple. Take it to the customer service center or the watch repairer, do not need to open the cover, directly use the demagnetizer (or called the degaussing machine, the must of the watch repairer, the market price is only a few hundred yuan) for demagnetization, and the watch can return to normal in 2 seconds. Nowadays, there are many anti-magnetic watches, but the so-called anti-magnetic watches are not all parts of the watch are anti-magnetic, only the main parts, such as the balance, hairspring, spring and other parts made of anti-magnetic materials.

Although it is an anti-magnetic watch, it can only serve a preventive role, so you should avoid placing the watch next to electrical appliances or magnetic objects that generate magnetic fields.

If it is a ** table, then the reason for magnetization should be considered first.

The magnetic field is everywhere, and it is impossible to prevent it, and it turns out that with a good end of the watch, the error suddenly becomes larger, and the first thing to guess is whether it is magnetized. There are many steel materials in mechanical watches, such as large and small steel wheels, escape wheels, shaft tenons of gears, bearings, screws and hairsprings, so watches are very susceptible to magnetization. Once the mechanical watch is magnetized, the impact is first of all to increase the error, and in serious cases, it will also stop the watch.

The principle of the demagnetizer is that it can produce an alternating magnetic field, and the watch will be demagnetized if it is a constant magnetic field. Demagnetizers can be bought or made by themselves, and generally professional watch stores have demagnetization services.

Because there is no manual spring in the fully automatic period, it is okay to shake it a few more times with the watch, which may be a lack of kinetic energy.