How to quickly import an automatic screw machine program

Ant automatic screw machine: Since the operation function interface of different automatic screw machines will be different, but it is roughly the same, you can refer to the following steps to import the automatic screw machine program:

New Product Introduction Instructions Steps:

Step 1: After the automatic screw machine is opened, check whether the gas and electricity are normal, and then adjust the required torque through the torque meter.

Step 2: 1. Observe whether the screw feeder is suitable for the screws currently used, if not, we need to adjust. After adjustment, try to absorb about 50 screws and observe the effect.

2. Take out the electric bit, and then take out the electric bit to observe whether it is suitable for the current screw.

Step 3: Set the suction position of the automatic screw machine, after setting, we must first manually suck about 30 screws, observe the effect of suction and whether there is a runout phenomenon after screw rotation after suction, and then adjust the position and nozzle depth appropriately.

Step 4: Adjust the position of the fixture block and the position of the cylinder, the position of the cylinder should be about 4mm away from the edge of the product, and the product is not loose or tight after the adjustment of the front stopper, so that it is convenient to take and place the product, and the product placement direction on the left and right sides should be consistent.

Step 5: Set the number and name of the current product, and enter the model query page to observe the previous program number before setting.

Step 6: 1. Put the product into the left fixture, click the setting page to enter the left step setting. Start by determining the lock-in order and the total number of steps.

2. Set the first screw locking position, move the locking mechanism to the top of the first point position by adjusting the handle, and then slowly descend the Z-axis, and observe the height of its nozzle at the same time. (Note: The nozzle must be higher than the highest position of the product, and the lowest position of the nozzle is limited by adjusting the screw.)

3. If the Z-axis continues to decline, the bit will slowly expose the nozzle, at this time, we should pay attention to whether the position of the nut of the bit and the product is concentric, and then observe the difference between the front and back and the left and right, and then slowly adjust.

4. After determining the position, press and hold the OK button to save the current coordinates. Then move the z-axis to the highest point and move to the second point, and confirm it in turn.

Step 7: 1. Enter the "Left Coordinate Correction" page, press and hold the Copy to Right button to copy the program to the right platform.

2. Then enter the "Right Coordinate Correction" page, and press the correction button after the first point of correction.

3. Go back again: "Right coordinate input" to locate each point at once.

4. Finally, enter the "Left Manual Input" page, enter the parameters such as deceleration position and locking depth, and press Save.

Step 8: Put the product into the left and right fixtures of the automatic screw machine, pay attention to the consistent direction of the left and right placement of the product, and then start to test the lock.

Step 9: Observe the lock-up effect and modify the parameters until the lock-up is good and stable.

The program box of the automatic screw machine is generally a hand-held teaching box, this kind of program can be used point-to-point, block-to-block, face-to-face copy and import, Ruide Xin is a better PLC, which can be directly imported into the CAD drawings with a U disk into a working program.

There is a manual for buying a fast flying effect automatic screw machine, and there will be someone to guide you, so you don't have to worry about this problem when you buy something!

The flying effect automatic screw machine is used like this:

Turn on the power, turn on the air source, and adjust the torque; Pour the screws into the screw silo, and the amount of screws should not exceed the height of the screw conveying track; Before locking the screw for the first time, check whether there is a screw to be locked in the nose of the electric batch; If there is no screw to be locked on the nozzle of the electric batch, it is necessary to press the manual screw button to make the machine move twice to ensure that there is a screw on the nozzle of the electric batch waiting for the locking screw; After ensuring that the electric batch adjustment button is in the position of the lock screw, hold the electric batch in one hand, hold the lock screw workpiece with the other hand, and press the locking screw down on the screw hole; When the electric batch reaches the preset torque and automatically stops, lift the electric batch and lock the second screw; And so on and so forth.

It is written in the technology center of the official website, welcome to view!

It's about 14,000-16,000 yuan, a single-axis handheld automatic locking screw machine.

First of all, we need to know that automatic screw machines are divided into several types.

According to your own needs and economic affordability, you need to choose a suitable automatic locking screw machine to use the method depends on what style of machine you buy, whether it is fully automatic, or close to fully automatic, or semi-automatic.

The usage is largely related to the system that the manufacturer installs for you. If you are using an unfamiliar system, you need to contact the manufacturer to send an instruction manual, and if you can't understand it, then find the manufacturer.