Does the automatic screw screw machine have any requirements for screws?

The requirements for screws of the automatic screw machine are as follows:

1. Screw length and specifications. The total length of the screw must be greater than the length of the screw cap, and the depth of the screw hole must not exceed 40mm. When working, be sure to check whether there are obstacles within 10mm around the screw holes, because the obstacles will definitely affect the operation in production.

In addition, the surface of the screw hole must be an inclined plane with a flat surface of less than 30 degrees.

2. Whether it has a gasket.

If the screw has a gasket and the gasket is larger than the screw cap, then the diameter of the gasket should prevail, so that it will not be flipped in the feeding pipe. If the screw does not reach the total length of the screw more than the screw cap warp, then the feeding method should take adsorption or other methods.

3. The thread of the screw.

The thread of the screw is not the same, there is a triangular self-tapping locking screw, which is the same as the pitch and angle of the metric thread, but the cross-section is a triangle, and there are two parameters of D and C value to control the locking. The locking function can be achieved.

The automatic screw screwing machine is suitable for various types of screws, such as commonly used Phillips screws, hexagonal screws, slotted screws, hexagon screws and so on. In addition, according to the length of the screws, it is possible to configure an automatic screw feeder with adsorption type or air blowing type. Ruidexin blow-off automatic screw screwing machine has high requirements for screw size.

The diameter of the screw nut and the total length of the screw need to exceed the above ratio.

There are two types of automatic screwing equipment: handheld and mechanical automation, which can be divided into various types.

Hand-held should belong to semi-automatic equipment, need manual operation, wind batch, rechargeable electric batch, brushed electric batch and brushless electric batch, etc., need to manually put screws and align screw holes, the speed is slow, and it can also be more screw feeder to form a semi-automatic lock screw equipment, no need to manually put screws, hit a screw will automatically send a screw, the efficiency is much faster.

Duoweisi specializes in the production of automatic screw locking machine manufacturers, with the production of brushless electric batch, mechanical electric batch, screw feeder and other supporting equipment and various types of automatic screwing equipment, is a subsidiary of high-tech enterprises, good technology and strong strength, can be customized non-standard, there are screw fastening problems to find Duoweisi.

Summary. Deficiencies of hand-held screwing performance: 1. Screws below m2 cannot be completed; 2. Screws with gaskets cannot be completed by handheld semi-automatic screwing machines; 3. When the length of the screw tooth is less than or equal to the diameter of the screw head, it cannot be completed; 4. When the screw counterbore exceeds 2mm, it depends on the length of the screw.

What is the difference between machine screwing and manual screwing?

Deficiencies of hand-held screwing performance: 1. Screws below m2 cannot be completed; Mingda 2. The screws with gaskets cannot be completed by a handheld semi-automatic screwing machine; 3. When the length of the screw macro comic tooth is less than or equal to the diameter of the screw head, it cannot be completed; 4. When the screw counterbore exceeds 2mm, it depends on the length of the screw.

Advantages of automatic screwing machine performance: automatic screwing machine is divided into two kinds of mechanical equipment: desktop type and first-class type. 1. Screws below m2 can be completed by vacuum suction or magnetic suction conveying; 2. The screws with gaskets can be completed by a fully automatic screwing machine, which should be selected according to the screws and products. 3. When the length of the screw tooth is less than or equal to the diameter of the screw head and the paulownia pin, it can be completed by vacuum suction or magnetic suction conveying; 4. The depth of the screw countermere is not more than 40mm, but it depends on the screw and the screw above the diameter and length of the screw. 6. Manual loading and unloading, no manual operation, complete the automatic screw process, such as the use of multi-electric batch screwing, than the handheld semi-automatic improvement of several times; 7. Its first-class automatic screwing machine is to cooperate with the production line to set up the payment position and automatically rotate to complete the screwing process.

Summary. It is relatively simple to do screws, mainly heading machine, tooth rubbing machine, 0 each group, you can according to the size of your screws, appropriate more than one group, etc., simple screws are not large, second-hand you had better find the kind of factory that wants to go out of business, this kind of machine will be better, equipment directly from the second-hand market, laymen may not be able to buy good equipment. The equipment is not high, basically tens of thousands.

Or contact the factory where you bought the equipment. Other electroplating and heat treatment can be sent out. The investment can be 10-200,000 yuan.

It's all about business. If the business is unstable, the value of the equipment will depreciate as soon as it is bought.

Hello, I am helping you to inquire about the relevant information and will reply to you immediately.

It is relatively simple to do screws, mainly heading machine, tooth rubbing machine, 0 each group, you can according to the size of your screws, appropriate more than one group, etc., simple screws are not large, second-hand you had better find the kind of factory that wants to go out of business, this kind of machine will be better, equipment directly from the second-hand market, laymen may not be able to buy good equipment. The equipment is not high, basically tens of thousands. Or contact the factory where you bought the equipment.

Other electroplating and heat treatment can be sent out. The investment can be 10-200,000 yuan. It's all about business.

If the business is unstable, the value of the equipment will depreciate as soon as it is bought.

Heading machine, tooth rubbing machine is enough, generally also supporting the grinding machine, lathe, used to quickly repair the mold, of course, if you only do standard parts or your master will not repair the mold, these can not be used, the mold is not good to send directly back to the mold factory, but the efficiency is too slow, so that the milling groove cutting machine, the amount is not much on the outgoing processing can be sent, after all, the new factory to save money. If you want to buy a new machine or a Taiwan machine to make high-quality screws, it is only used on furniture, and the cost of domestic machines or second-hand phones is low, but it will not take a few years, and the accuracy is not high.

Hope mine can help you.

Heading machine and tooth rubbing machine.

Heading machines can be divided into shoelace heading machines and screw heading machines according to the different industries used. Generally, when used, any combination can be made, and generally does not appear in an independent form. For example, semi-automatic single-knife mechanical rubber feeding shoelace heading machine, automatic double-knife computer glue feeding shoelace heading machine, automatic double-knife mechanical glue feeding gift belt heading machine.

The heading machine belongs to the cold heading equipment, the function is to punch a die and two punch products, mainly for the head forming of screw products, and its working principle is wire straightening, wire feeding, shearing, feeding into the main mold, one punch initial forging, two punch forming blank exit. Its work is done in one go, and the production capacity can reach about 200 capsules per minute, which is a relatively advanced product with current technology.

Components.

1. Automatic feeder.

The automatic screw feeder is mainly responsible for the screening, arrangement, detection, indexing and conveying of screws, which is an important link instead of manual screw removal.

According to the feeding method, it can be divided into blowing and suction type and adsorption type.

Air blowing type: Blowing type feeding is a feeding device equipped with a conventional automatic screw tightening machine. The blown feeder is used to screen, arrange and test the screws.

The screws are automatically conveyed to the lower part of the clamp of the locking mechanism through the air pressure through the feed pipe, waiting for locking. The equipment screws are synchronized with the feed screws without stopping the machine.

Adsorption type: Adsorption feeding is often used for coordinate mechanical feeding, which is a better general feeding method. Screw conveying, testing and discharging are all completed by the screw discharging machine.

The coordinate machine pulls the screws back and forth, and then performs the screw tightening process. It has the advantage of not being affected by the size of the screw.

Second, the locking mechanism.

The locking mechanism (called the locking module in the industry) executes the tightening action by configuring the batch, air blowing batch or servo motor according to the program setting, completely replacing the manual operation.

According to the different locking mechanisms, it can be divided into electric batch, air blowing batch, servo drive, etc. The torque of the wind batch is large; It can be locked according to a given servo torque value, which is more accurate and faster.

3. Power box.

The control system of the locking mechanism is mainly located in the electrical box with an input voltage of 220V. It is usually controlled by PLC (or single-chip microcomputer) to realize the collaborative work of automatic feeding and locking mechanism to achieve automatic locking effect.

Fourth, the positioning system.

The positioning system (motion module) mainly ensures that the locking mechanism can accurately screw the screw into the screw hole position of the product. Positioning is done by a variety of accessories such as tables, fixtures, fixtures, etc. It is usually necessary to design according to the shape characteristics of the product.

Grid for automatic screw machine has the following benefits:

1.Speed up the work efficiency of workers, save time, and thus reduce the production cost of a single product;

2.It can also reduce the labor intensity of workers while speeding up work efficiency;

3.The electronic counting screen of the automatic screw machine can alarm and prompt the abnormal working status;

4.If the production line of the factory is equipped with automatic screw machines, the company's image can be enhanced;

5.The automatic screw machine can also detect the pass rate of product assembly.

Fully automatic screw screwing machine, one person can operate multiple machines for sitting work, and multiple screws can be locked at one time for multi-axis work.