The computer keeps stopping at the screen when it was just turned on

The top shift is regrettable and breaks the reef

Staying on the boot screen when booting up means that the system has failed to boot, and it can also mean that the system is damaged and the system must be reinstalled.

Caused by driver conflict: press F8 to enter safe mode when booting up, if you can enter safe mode normally, it is caused by driving conflict. Think about what software you have installed, drivers, updates that are caused by patches, and uninstall them in safe mode.

Caused by poor contact of the hard disk: open the chassis and reseat the hard disk, connect the dual-wire hard disk to the motherboard interface, and replace one.

What should I do if my computer is stuck at boot screen?

Below is the interface where the BAI machine is stuck:

1. First of all, I press F8 when I boot up to enter the safe mode interface. But when I went in, I waited for a few minutes and there was no response, and it kept saying please wait a while.

2. There is no way but to press the reset button to restart the computer, because the computer was installed with a one-click ghost backup before, so I decided to restore it and try it, but it is still the case after the restoration. The computer is still stuck on the "Starting Windows" screen.

3. I can't tell what the reason is for the time being, guess it's a problem with the ghost backup before, so I enter the PE system to take a look, restart and press the delete key, enter the boot interface, set the boot to U disk start, enter the PE system, reinstall it with the newly prepared Windows 7 in the PE system, after the installation and restart, the computer boot is still stuck in the "starting Windows" interface.

4. After the above two steps, it is certain that there is no problem with the system, but what is the problem? Problems with hardware settings? Factory reset?

Discharging the batteries in the motherboard? Turn off the main power of the computer, open the case, remove the battery from the motherboard, clean up the dust, and put it back in.

5. Then connect the power, turn on the computer, OK can enter the system, for convenience and speed, restore the system with the previous ghost file.

The motherboard battery discharge is mainly to clear the CMOS settings, removing the battery will restore the BIOS settings to default, and can also be used to clear the password.

Situation 1: The computer has been stuck in the "Starting Windows" interface after booting Reason: It may be caused by the computer's hard disk or memory module, we can re-insert or replace the computer memory module and hard disk to solve the problem, if it still doesn't work, it is the system reason, just redo the system.

Solution: After the computer boots up, press Ctrl+Alt+del to automatically restart the computer before entering the "Starting Windows" interface, and then the Windows system can run normally.

Situation 3: Stuck in the "Starting Windows" interface at boot, the above methods are useless. Reason:

This situation is generally when we replace or add hardware (such as graphics card, hard disk, etc.) and then do not redo the system, resulting in the system is not compatible, and then the original system cannot enter, and it has been stuck in the "starting windows" interface. Solution: Press F8 on the keyboard to enter safe mode when booting up, and ** drive the software to reinstall the system.

Questions. <>

That's what it looks like.

Don't worry, this is the interface where the computer is starting, it may be because Windows is not compatible, and it is stuck.

Questions. Ok thanks!

It's okay. Questions. Bye.

Hello I have collected relevant information for you, please plan your trip in advance, and consult If the computer boots up and stays in the windows icon interface, is it that the system has been updated before, or has you installed any programs? 1. The computer is turned off, and then turned back on. 2. If it is caused by updating the system patch, then you need to uninstall the system patch.

If it is W10 into safe mode, you can force shut down 3 times first, and then restart the computer will appear in the recovery interface - select safe mode - and then the computer will restart into safe mode, after entering safe mode, open Settings, then click System & Security, click View Update, and then uninstall the latest updated patch, before restarting the computer. 3. If the system problem is deleted, this needs to install the system 4. If it is caused by the installation of software, go into the safe mode and uninstall the corresponding installed program. Have a great day.

What is the reason why you consult the computer that does not turn on and stays on the boot screen?

There are many reasons for this situation, but most of them are related to hardware, for example, the BIOS battery is out of power or the BIOS storage is wrong, it will generally stay on the boot screen, in this case you need to turn off and disconnect the computer power, take the BIOS battery off, wait for about 10 seconds, and then reinstall the BIOS battery or replace a battery, and restart it in the save, so that the problem can be solved.

If you still can't get into the system, the problem is the same, then you have to see, other hardware such as memory or hard disk or graphics card may affect the normal boot of the computer into the system, you can turn off the computer, re-insert the memory, hard disk and graphics card, should also solve the problem of not being able to boot normally!!