How to set up TP link mini wireless router

I'm using the same as yours now.

1.First set your IP address, as long as it's not).

Subnet mask Gateway.

2.Enter it on the web page.

Once opened, a login dialog will appear.

Username: admin

Password: admin

This is the initial password that you didn't change your username and password.

After a successful login.

Click "Setup Wizard" on the left, the instructions for the setup wizard appear on the right, click Next, select ADSL Virtual Dialing (PPOE), enter your Internet access and Internet password after the next step, and save it in the next step.

3.At this point, you can connect to the Internet normally, and the rest can be set up according to your needs (or you can keep the status quo).

There are too many specific routing steps on the Internet, you can see for yourself, and I will say some precautions. First of all, look at the IP address and username password that comes with the back of the machine, the IP address and your main router do not conflict, if there is a conflict, you can not connect to the network cable first, after setting up the mini, follow the setup wizard step by step, and finally restart, after your main router is disconnected or restarted, your mini is best to restart together, I hope to help you.

If you want to use your wireless router on the unit and use WiFi, then you need to parse the WLAN and set the LAN in the router settings interface

It's all about getting it right!

1. In the first step, first turn on the computer, click on the network connection icon in the lower right corner of the computer, then click to open the network and sharing center, then click on the wireless network connection, and click on properties.

2. Step 2, then select the IPv4 option, then click Properties, then select Automatically get IP address and DNS address, and finally click OK.

3. Step 3: Enter in the browser, enter the login password (the default is admin), enter the management interface, select the setup wizard, and then select the AP access point mode.

4. Step 4, then you can set the name and password of the wireless, and then click Next, after the setting is completed, Sominying restarts, and then logs in to the management interface (the default password is admin).

5. Step 5, click the setup wizard, select the bridging mode, click Next, modify your name, select the same channel as the main route, then scan, select the signal of the main route, connect, enter the password of the main route, and click Next.

After setting the secret code of the mini router, restart it after the setup is complete. Complete the steps.

Here's how to set up the mini router:

The appearance of the mini router is somewhat different from that of a normal router, but the specific setting method is actually similar.

1. The broadband bus (the network cable from the cat) connects to the WAN port of the router.

2. Connect one end of the network cable to any LAN port of the router, and connect the other end to the computer, and start the computer and router equipment;

3. After starting the device, the computer opens the browser and enters it in the address bar to enter the wireless router settings interface. (The default address is different for different routers, and the back of the router is usually labeled).

4. An account and password to log in to the router appear in the settings interface, enter the default username and password admin (the default username and password are different for different routers, and the back of the router is usually marked).

5. According to the setting wizard step by step setting, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

6. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

7. Click Wireless Settings, Wireless Security Settings, enter the password to set wifi, and finally click Save.

8. After saving, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can surf the Internet normally after restarting the router.

The hotel's network cable is connected to the LAN port of the wireless router.

Turn off the DHCP auto-assignment IP address function for your wireless router (because DHCP is already enabled for the router in the hotel).

Set the IP address of your wireless router (the hotel is set manually, do not set this value, for fear of conflict with the hotel IP).

DNS: Then your laptop also sets the IP manually

dns：

The cable pulled out by the broadband client is connected to the LAN WAN of the router, and then the computer is connected to the router wirelessly or wired in the state of power on the two, and it is best to connect it wired (to buy the root network cable to connect the router LAN port and the computer network card port), when the small computer logo in the lower right corner does not appear bad or exclamation mark, you can enter this address in the browser, and you can enter the settings page.

If the above method does not work, then simply connect the computer and router first, and do not connect to the broadband client.

Connect the line first, and then go to the router to set up broadband dial-up Internet access.

The details are as follows: 1. Connect the line between the network cable, the router and the computer, and start the computer and the router equipment;

2. Look through the nameplate or instruction manual at the bottom of the router to find the router IP, default account and password. If the access is optical fiber, the IP address of the fiber modem must not be in the same network segment as the router IP address, otherwise it is easy to conflict.

3. Open the browser, enter the IP address and press enter, if the input prompt is incorrect, it means that it has been modified, you can only press and hold the reset button on the router to restore the router to factory settings and reset it;

4. Enter the router login interface, enter the default login account and password queried, if the input prompt is incorrect, it means that it has been modified, and can only be reset after resetting the router by pressing and holding the reset button on the router;

5. Enter the router settings interface, find the setup wizard on the left menu bar, select Next according to the prompts, and select PPPoE dial-up Internet access;

6. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

7. Set the wifi password, try to make the alphanumeric combination more complicated and not easy to be rubbed off the network (this step is for the router with wifi function, and without wifi function, go directly to the next step);

8. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

1. You connect the network to the L-WR800N socket, connect the power supply, and the whole room will achieve Wi-Fi wireless coverage. Take out your laptop, Wi-Fi phone, and iPad to access the Internet wirelessly.

2. However, L-WR800N is not encrypted by default, the wireless network at this time is not secure, anyone is connected to the device to surf the Internet, it is recommended to set wireless encryption. That's where laptops come in.

Step 1: Configure the notebook.

In"Computer Desktop - Start - Control Panel - Network Connection"page, select"Wi-Fi connection"icon, right-click and select.

Choice"attributes", specify and save the IP address of the wireless NIC as shown in the following figure.

Step 2: Set up the router.

1. Open the browser, enter the management interface of the router, and enter the use of the router in the pop-up login box.

Account name and password"admin/admin";Click"Setup Wizard", select"Next", 2, click"Next"Start the setup, pop up the work mode settings page, and select"AP mode"。

3. Click"Next"The wireless settings page pops up.

Note: The SSID is the name you search for when you connect wirelessly (used to distinguish it from other wireless routers), in order to prevent illegal users from accessing the network, it is recommended to set wireless security, and it is recommended"wpa-psk/wpa2-psk"and set a password.

4. Click"Next", indicating that the device needs to be restarted.

Click"Reboot", the router automatically reboots, and the setup is complete.

5. After the configuration is completed, please reset the IP address of the wireless network connection to the original configuration (automatically obtain the IP address and automatically obtain the DNS server address), and click"OK"takes effect to connect to the Internet properly.

Step 3: Complete the setup and reconnect to the wireless network.

At this time, the wireless network of the TL-WR800N has been set with wireless security (encryption), the wireless network connection of the laptop will be automatically disconnected, you need to reconnect to the wireless network of the TL-WR800N, and you need to enter the wireless PSK password of the TL-WR800N to connect to the Internet during the connection process.

The above is an example of how to set up the mini TPLlink wireless router of L-WR800N, if you use TPLec, then the method is the same, just copy it directly.

Restore your router to factory values first, then enter it in the browser, enter the account and password, usually admin

The gateway is generally input to see if it can be connected, if not, press the reset button behind the router for 5 seconds and then enter the gateway.

It is recommended that you call ** directly to ask customer service, it is very convenient, I will never get it, I asked customer service today, just a few minutes.

How to set up the TP-Link Mini Wireless Router

TP-Link Mini Wireless Router selects the routing mode.

TP-Link Mini Wireless Router Setup Wireless Method:

Home Network Environment Cabling]:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter the Internet user name and password according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

Turn on the router's wireless function].

1. Select Wireless Settings --- Basic Settings.

2. Check [Turn on wireless function] and click Save.

Set wifi password].

1. Wireless Settings - Wireless Security Settings - Select [WPA-PSK WPA2-PSK].

Authentication Type: Automatic.

Encryption algorithm: AES.

The PSK password is the wireless password. Set the required password.

Generally, the routing factory settings are not encrypted passwords, so the computer will be automatically connected, once you set the account password, it will automatically disconnect this link, at this time there will be a signal of this route at the network connection, but the password is required, re-linking to the router means that it will be automatically disconnected after setting it up and reconnecting on it.

Hearing you say that, I think you must have not entered your Internet access and password. Follow the setup wizard, there is a step to enter your Internet access and password, you enter the back is still the same, and finally restart the router and you can use it. A router is equivalent to a tool that automatically dials up the Internet and realizes network sharing, not that you can access the Internet as long as you have a router.

Internet access is still based on passwords.

It's not clear to say, it's better to have **, have you set a broadband password? In addition, there are places where the restriction route will be bound to the mac.