How to repair TL WDR8620 lightning strike? 90

If lightning strikes need to be repaired, directly find a dedicated maintenance personnel.

I've told you about it, line failure! The cat first directly connected to the computer to see, if the problem is still there, hit ** to repair, if normal, check the indoor line and crystal head.

Hello! The WDR8620 router is set up as follows:

1. Connect the line between the network cable, the router and the computer, and start the computer and the router equipment;

2. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface.

3. An account and password for logging in to the router appear in the settings interface, enter the default account admin and password.

4. Set up step by step according to the setup wizard, choose the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

5. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

6. Set the wifi password, try to make the alphanumeric combination more complicated and not easy to be rubbed into the network.

7. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can surf the Internet normally after restarting the router.

You can set how your router will be connected You should now set up to connect when you need it.

It is recommended that the landlord find a place to buy and return to TP-Link for warranty and maintenance.

Some routers of the new version of TP-Link firmware cannot enter the flash mode through the dust and stupid way, if the landlord really wants to disassemble the brother by himself, he can use the programmer to write the ROM and then replace the ROM chip to try.

TP-Link TD-8620 is not bad! Stable performance!

Device type: External ADSL

Supported protocols: ANSI, interface types: RJ45, RJ11

Product Features: It provides one 10 100M adaptive port, one RJ11 interface lightning protection enhanced design, provides web interface management through 4000V lightning test standard, and supports software upgrades.

Due to the hardware design defects of TPLink and other single-chip microcomputer WiFi routers and the serious simplicity of materials in manufacturing, they cannot efficiently process the data and throughput from network applications such as games, so a WiFi router with excellent performance is very important for the entire wireless network speed, signal strength and stability.

The wireless router needs to be set up according to the Internet environment. Different Internet environments have different ways to set up wireless routers.

If it is a fiber modem wireless router that requires dial-up, set it up as follows:

1. Plug in the wireless router, don't connect the cat first, and connect the computer to any LAN port of the wireless router;

2. Enter the IP address of the router in the address bar of the browser (on the label behind the router), and enter the login username and password to enter the settings page;

3. Set up according to PPPoE (ADSL virtual dialing) mode, enter the Internet account and password;

4. Set the SSID, encryption method and password;

5. Save and restart;

6. After setting, connect the network cable from the cat LAN port to the WAN port of the wireless router.

There are a lot of problems with this router, it's really not good, and the power consumption is also large, look at the power adapter to know 12V3A, the power consumption reaches 25W, and the compatibility is very poor, if the LAN of the wired network is only connected to the computer, there is no problem, if more than 2 are connected, one of them can not automatically obtain IP and can not access the network. I was disappointed to see the ads and bought this router.

OK,The maximum speed can reach 2600M,It can be said that it has exceeded the specifications of all computers and mobile phone wireless network cards,Wireless is relatively advanced,MediaTek MT7621 dual-core processor is used internally,Support 1000M wired port,Support more than 100M fiber broadband bandwidth,There is no pressure to run broadband within 500M,But the firmware function is more general,TP-LINK's firmware can't play the function and full strength of this router's built-in hardware, It is a product that is relatively simple to set up.

Dual-band router, wide coverage and stronger performance, no problem for home use.

Ways to solve the router setting abnormality (frequent disconnections):

Press (hold for 5 seconds) the router's reset button and wait until all the lights are on together for the reset to be successful.

After the reset is successful, you will need to set up the router again (there is a wizard), because it has been restored to the factory defaults.

DHCP Server DHCP Service is enabled.

Address rental period is 120 minutes by default (if the network is disconnected for 2 hours, you can set a longer time) Save.

My model is the same as yours, and the problem is the same as yours.

Has your router dropped call problem solved? Can you help me?

TP-linktl-wdr8620 is easy to use.

TP-Link dual-band wireless broadband router, wifi home high-power gigabit 5g through-the-wall king, 2600m high-speed smart optical fiber, tl-wdr8620 full gigabit port, the performance and quality are very good, and the wireless signal is strong.

Brand: TP-Link Router.

Internet speed: 600m

A high-performance WiFi router is crucial to the speed, signal strength, and stability of the entire wireless network.