Is it a DI 604 router issue

The DI 604 is a broadband router for use in small networks such as homes. According to your reason, it is likely that the router is crashing due to too much traffic or too many connections.

First see if the people in your company are using multi-point ** software such as BT, and if possible, it will be better to limit BT. Because BT** requires a lot of connections, your router may not be that strong.

etherpeek nx。You can intuitively see the traffic of the machines in the network and the protocols used. There's more to this software than that.

You can try. By the way, I use the version, there is a special crack on the Internet, no need to register.

I also used 604+ to take 21 of our company's machines to connect to Tietong 6m broadband, and I have never encountered the problem of dropping the line to you.

The 604+ is not too hot when it works, it is probably close to 40 degrees, so I don't think it should be overheated.

In your question, it says that even the switch is disconnected, this may be due to the external network, and it is best to ask the operator to come and see if it is the cause of the router.

If it is confirmed that it is the router, it may be that the traffic is too large as it was said upstairs, or it may be that some settings of the route are inappropriate, you can consult the network 8008296688 of Youxun

If you need to throttle traffic, 604+, fortunately, you can select the corresponding port (the physical port connected to the router) and speed in QoS.

In short, the reason for the disconnection is complicated, and it is best to confirm whether it is the cause of the route itself.

DIR-605 Router Setup Method:

Home Network Environment Cabling]:

1. There is a telecom cat: the telecom cat --- router WAN port; The LAN port of the router --- a computer.

2. No telecom cat: network cable --- router WAN port; The LAN port of the router --- a computer.

Computer enters the router]:

1. Open the browser - enter the general router address is this) incoming route - enter the user name and password, (the default is admin).

Set Router Dialing]:

The IP and DNS settings of the computer are automatically obtained.

1. Enter the router. In the [Setup Wizard], select [PPOE Dialing] (some are ADSL dialing), follow the prompts to enter your Internet username and password, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPOE Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

Connect the wireless router to the computer first, open the browser, type in the local connection IP address, enter the router settings interface, enter the account number, password (the bottom label of the wireless router is written) and select the wireless switch to turn on, and exit when finished.

The router power switch has a small space that is recessed.

Press it with a toothpick.

Must be electrified.

This restores the factory defaults! Hold down about one.

5-6 seconds.

Look at the lights go out. Prove it again.

Factory reset by default.

Then you're in the incoming route.

Set it up from scratch.

Let's see if it works.

First of all, it is necessary to determine that it is a problem with the router and Thunderbolt software.

2. If the problem still exists, the possibility of troubleshooting the hardware of the router is the setting of the router and checking the settings of the router.

Laptops are filtered by MAC physical address, and the most fundamental way is to upgrade the router's firmware to the latest version officially released. You try the wired connection first, but I personally estimate that it is a firmware problem, and it is safer to find a merchant to help flash the firmware during the warranty period.

How to enter]:

Method 1:1: Check the router login information on the back of the router.

3. The router login interface pops up and enters the default login username of the router: admin and password: admin.

Method 2: 1, check the IP first, method: win+r--- enter: cmd--- enter in the black and white interface: ipconfig, press enter.

4. Pop up the router login interface and enter the default login username of the router: admin and password: admin (if it is incorrect, look at the back of the router).