The router signal is very good, but the mobile phone can t connect to the Internet, what s the matte

If the settings are incorrect, connect the computer network card with the LAN port of the router with a network cable, and turn on the power of the router; Double-click the IE browser on the computer, enter the IP address of the router default settings page in the address bar, and press Enter; Enter the default username: admin, and the default password:

admin；Click OK. Click Setup Wizard in the left rail, click Next; Click on ADSL Virtual Dialing (PPPoE) and click Next; Enter the broadband, password, and click Next; Click Done. Many friends think that the dial-up connection is over after setting up, but in fact, there is still one point that is not completed.

Because the following settings are not completed, many friends fail to dial up, or can connect to the network, but it will be dropped after a short time. Let's continue the settings: click the MAC address clone menu in the network parameters menu on the left sidebar, click Clone MAC address in the interface that appears, and click Save.

At this point, the router will prompt you to restart the router, click OK to restart the router. After the router restarts, close the Internet Explorer. Connect the WAN port of the router with an incoming network cable, and then connect the computer to the LAN port of the router with a network cable to start surfing the Internet.

Hello, wifi signal regardless of whether there is a network mobile phone and other devices can be connected, the user can not use the network after connecting to wifi, first confirm whether the broadband line of your bench is smooth, you can check whether the indicator light of the broadband cat has LOS red light flashing, if there is a broadband failure, so the router's wifi can not use the network, at this time, the user can call the operator's customer service to report the fault, and there will be staff to come to the door to troubleshoot the fault after the fault report.

If the broadband modem can be connected to the network normally, then it is a problem with the router, and you can check whether the network cable is connected correctly. If the network cable between the broadband modem and the router is normal, then the user can restore the router to its factory value, and then reset the router parameters to see if the router can be restored to normal

2. Then open the browser and enter the management address and login password of the router.

3. After logging in to the background, click the setup wizard, and then fill in the corresponding parameters according to the wizard instructions.

<>6. After the wireless setting is completed, click Save, and then restart the router to use it normally.

If you can't connect to the WiFi network with your vivo phone, you can check the following information:

1. Check whether the wifi password is correct.

It is recommended to click when entering a password"Eye icon"to display the password and make sure that the password is correct.

2. Reconnect to WiFi

Please go to Settings --WLAN, click on the wifi you need to connect to, and click"Forgot Network Forgot password"reconnect.

3. Check whether the wifi network is normal.

Please compare whether the same wifi connection is normal with other mobile phones, and confirm whether it is the wifi or mobile phone. If it is due to Wi-Fi, please restart the wireless router to check. At the same time, you can enter the router management interface to check whether there are special functions

Sakura does things such as limit the number of connections, MAC binding, Internet time management, etc.

4. Reset network settings.

You can enter the banquet - system management - backup and reset - reset the network - only bend - enter the lock screen password.

Note: Resetting network settings resets Wi-Fi, mobile data, and Bluetooth connection records.

5. Reset all settings.

After backing up the data, go to Settings - System Management - Backup & Reset - Restore all settings and follow the on-screen prompts.

Note: Restoring all settings will not delete any data or ** files, only all settings of the phone will be restored, some third-party application accounts need to be re-logged in, please confirm that it does not affect the use of the software before operating.

There are several reasons for this.

1 The mobile phone has been set to connect to a fixed IP, but the IP is wrong, so it can't be connected.

2.There is a problem with the router settings, or the router itself does not have an external network.

3。The router is dead.

Solution: 1 Check the line of the router first, whether the WAN port has been connected, and whether the light is flashing.

First, use the computer to connect directly to the router through the network cable, and automatically get the IP to try the stool, it seems that you may not be able to connect to the external network, if not, it is not connected to the external network, or there is a problem with the external network.

The router signal is good, which can only mean that the computer connection router is changing to the usual, not that it can access the Internet, so the reason may be that there is a problem with the network.

At this time, you can see whether the LAN port of the router is flashing, if not, it is a problem with the network cable; If it flashes, you can reset the route first

Step 2: Enter the account and password, usually admin (can be viewed on the back of the route);

Step 3: Enter the setup wizard interface;

Step 4: Choose the Internet access method: PPPoE;

Step 5: Enter the corresponding account and password (given by the business hall) for the broadband;

Step 6: Set the username and password for the wireless connection of the router, click "Save";

Step 7: Find the wireless information directly on the computer, enter the password to access the Internet.

If the network does not respond to the dust training in the sixth step, it is recommended to call the operator directly to solve the problem.

1. Please confirm whether the wireless router is configured correctly and whether the WAN port has obtained the IP.

3. If you can dial up the cat directly, only the router can't dial. Then it is generally the router hardware that is resistant to mountain obstacles.

4. If you can go to wifi, you can't go on it suddenly.

If it is related to the router cache, it is recommended that the user dial the power cord behind the router and replug it, and wait until the signal indicator lights up again, and then try to connect the mobile phone or computer.

As long as the wireless router is connected to the power supply, there will be a signal, whether there is a network or not is another matter, maybe the equipment or network cable in front of the router is not connected or malfunctioning, or it may be a problem with the router itself.

To put it bluntly, now the router is not powered on, it's simple, try to change the power supply, if you can't find it, then buy one, it is estimated that either your power strip is loose or your power supply is burned out. The worst-case scenario is that your router itself burns.

First, check whether the router is normal and whether the three lights are on. If you connect to the computer connected to the router to access the Internet, you don't need to connect again, you can directly access the Internet.

You can restart the router and mobile phone, if not, the cat will also restart, but it may be that you are disconnected, call ** to your network provider to ask.

It may be that the router is unstable, and it is recommended to restart the router on the road.

Our family sometimes has this reason, the signal is very good but not connected to the Internet, our home is a line is connected, dismantle it and reconnect it.

Try rebooting your router.

Thank you for adopting it if you are satisfied, and continue to ask if you are not satisfied.

This has happened to me in my house, and the solution: I have unplugged all the wires and plugged them in again, and my family is just like that.

I also have this at home.,It should be about the signal quality.。

Just restore the settings.

1. It may be that the router itself is not connected to the Internet, in this case, the router is also poor because the wheel can be broadcast, that is, the signal is issued, the reason may be that the network cable is not plugged in, or the network fee is due, and you can contact the operator after checking the network cable is normal.

2. There is a problem with the network settings of the mobile phone, and sometimes the slow liquid mobile phone configuration is too poor and it will crash. . . This possibility is relatively small, find another mobile phone to connect to the wifi to know)

The router is not connected to the Internet, you need to set up the road sales rental device, username and password, after the link to the Internet, the hand-portable spine machine can be used, or the router is set up IP, and your defense and penetration IP cannot be on.

Maybe you have used a smartphone to connect to the wifi and have a similar experience: you have entered the correct wifi password, and the mobile phone also prompts you to connect to wifi, but the network still does not work. There are many reasons for such problems, and the following will talk about how to analyze and eliminate them one by one.

Check your router settings.

Step 1: Open the browser of the computer connected to the current wireless router, enter part of the router in the address bar, check the bottom label of the router to know), log in to the web configuration interface of the current router, and the username and password are admin by default

Step 2: Under the network settings of the router, first find the WAN port setting option of the router. Setting the "type" correctly here is the crux of the matter.

There are two commonly used types: PPPoE and DHCP. Choose this according to your own situation.

If it is a home ADSL dial-up Internet access, choose PPPoE; If there is a direct network interface available, such as cell broadband or a hotel, DHCP is chosen

Step 3: If it is DHCP, there is no need to make other settings, and the router will automatically obtain the corresponding network settings. If you choose PPPoE, you need to fill in the correct username and password, which are provided by network service providers, such as China Telecom, and if you forget your password, you can call 10000 for manual consultation.

Step 4: Next, check the LAN port settings of the router. The settings of different brands are actually similar, the most important thing is to turn on the DHCP function, so as to ensure that the router can assign an IP address to the device when it is connected to the LAN port or connected to WiFi, and the IP address range assigned by DHCP should be in the same network segment as the IP address of the router, for example.

Check your phone's settings.

Step 1: Open your phone's settings, select "Wi-Fi", and then, when you see the wifi signal that you are currently connected to, click on the small blue circle arrow on the far right.

Step 2: Click "Ignore this network". Then, the wifi connection of the mobile phone will be disconnected, so that the mobile phone will not automatically connect when you click to connect to the signal source again, but will re-enter the connected wifi password, that is, the mobile phone will re-identify the network once, so that you can achieve the effect of emptying the original network configuration.

Step 3: If you want to clear it more thoroughly, you can open Settings ---General --- Restore and select "Reset Network Settings". In this way, the device will restart, and after the restart, all previously connected networks will not be saved, but will be recognized as a new network, and the wifi password will be entered to connect.

The mobile phone can receive the signal of the wireless router, but it cannot access the Internet Reason:

Router dialing is not set up.

Solution: Computer enters the router].

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter the Internet user name and password according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.