After the wireless router is set up, it still can t be connected to the Internet, where does it need

After making sure that the password is entered correctly, try to clone the MAC address in Network Parameters --MAC Address, and set a fixed IP address for the computer if it doesn't work.

It depends on whether you have a dynamic IP or a static IP!

Here's how to fix it:Tool: iPhone 8

Operating system: iOS

Software: QQ Browser.

1. First open the browser with your mobile phone, as shown in the figure below

4. After entering the interface, enter the router username and password, and click to enter. As shown in the figure below:

5. Enter the interface. As shown in the figure below:

6. Tap WiFi Settings. As shown in the figure below:

7. Finally, set the router parameters and password. As shown in the figure below:

It may be caused by the wrong settings of the wireless router, it is recommended to reset the wireless router to factory mode, and then set the corresponding Internet access parameters.

When the wireless router is powered off, hold or hold the reset hole or button on the wireless router for about ten seconds, wait for the indicator lights to turn off and turn on, the wireless router will restore the factory settings, and then connect to the computer for settings;

Any browser on the computer, enter the address bar for specific parameters See the parameters on the back of the wireless router), enter the account and password to log in to the wireless router manager background;

Setup Wizard - Next;

The default wireless router selects the Internet access method, the next step;

Enter the account number and password given by the operator when you report the installation of the network cable, and the next step;

Set the wireless network account (SSID) and encryption password, next step;

Click Done.

Let me tell you how to use the router to connect to the Internet, and you will find it very convenient after using it.

1. Connection: The optical fiber into your home is first connected to the ONT (rented to you by the mobile company, now Huawei brands are the majority), and then the ONT is connected to the WAN port of the router with a network cable (it is best to buy a wireless TP-link, the effect is better, and the mobile phone can be WLAN Internet access), and finally use the network cable to connect to your computer network card interface from the 2nd and 4th ports of the router.

2. Set your computer's IP address to and subnet mask to be, then open the Internet Explorer, enter the IP address, press Enter, and you can see the router's configuration interface.

3. Select the network connection setting option in the configuration interface, enter the username and password (there is a description on the list given to you), remember to choose the PPPoE dial-up method, turn on the DHCP function, and then follow the prompts to complete the configuration.

4. In order to prevent others from rubbing the network, you can set a password for wireless access, which will be more secure.

5. Finally, your computer will be ready for Internet access. If there are two, it will be good to connect to port 3 of the router, and if there are three units, you can continue to connect to port 4. For wireless routers, you can access them via Wi-Fi.

6. Happy surfing the web.

Reset the router and set up the reason why you can't access the Internet:

Cause 1: The network line is faulty.

Home Network Environment Cabling]:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Reason 2: The router is misconfigured.

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter the Internet user name and password according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

1. Whether the port on which the router connects to the modem is WLAN;

2. Whether the router is set up to access the Internet correctly, telecom is generally ADSL, it is best to ask the operator;

3. Whether the account password is correct;

4. If there is an IP address in the running status of the router, the bottom display is disconnected, which means that you can access the Internet;

5. Whether the computer IP address and the router IP address are in the same network segment.

The infinity router you bought has an after-sales service. Or set it up yourself in the background. Or maybe the switch on the router doesn't turn on!

After the cable is connected, enter the router settings to see if it is connected, if it is not connected, try to connect it manually, and then it is not connected, there is a problem with the router settings. If the connection is normal, check that the IP, gateway and DNS of the computer are not set, and if the router DHCP is turned on, the computer will be set to get it automatically.

Hello, your problem needs to be analyzed according to the specific situation to know how your route should be connected and set up! And your broadband from the cat out of the network cable to the wan port can not access the Internet, it should be your settings are incorrect, and connected to the lan port can be on 3 computers, if you are sure that in front of your router is a cat, then is it a fiber routing cat all-in-one machine? Do you want to enable routing?

If it is not a routing cat all-in-one machine and the routing function is not turned on, then it is impossible to connect the network cable to the LAN port to enable three computers to access the Internet at the same time! Unless it's the case I mentioned above, or the cat you mentioned in the question supplement, it's actually a router! Please explain your specific situation before you can analyze it specifically, and then you can tell you if the specific connection and settings!

Look at this useless... Your default password is admin account

After entering, click on the setup wizard Next, then enter the correct Internet password and account number, and then set the wireless password of the wireless router Next, restart the router and it's OK··· I hope to adopt...

Connect the network cable on the cat to the WAN port (generally blue, the color of this port is different anyway) and then,Log in to the router on the browser,Set your dial-up account password。。。 Pay attention to the PPPoe method. . .

Then save it, and just restart the route.

Take a look at your local connection, how small the bytes received or sent are, or even 0!

Try slowing it down, and you're good to go!

Secret**Oh, don't forget to add points to encourage if you can!!

Right Health My Computer -- > Properties -- > Hardware -- Device Manager -- Network Adapter -- Select the network card you are on first, and select it from the drop-down menu on the right in the right value drop-down menu"10mbps half dupex"--OK--OK, that's it;

Check to see if your computer's IP address is automatically obtained.

Then, in cmd, type ipconfig renew

There are many reasons for the failure of the router to still not be able to access the Internet after it is set, and it is necessary to test to determine the fault point, and the specific test methods are as follows:

1. Set up the dial-up connection according to the requirements of the operator, connect the stand-alone device to the operator's optical modem, and ping the operator's gateway or DNS server address after dial-up the Internet;

2. If the ping is not working, it means that the operator's external network network is not connected, just call ** to find the operator to report for repair;

3. If ping, the external network network is normal and has nothing to do with the operator's network. If it is different, the fault is on the router, restore the router to factory settings, and then reset the router to eliminate the fault.

4. If the router still fails after step 3 above, you can judge that the router hardware is faulty and you can only replace the router.

Looks like there's something wrong with your setup.

Do you have broadband internet access? How do you set up your routing?

1.Enter the router address, after connecting the wireless router, enter the address you see on the router in the browser, generally of course, if your home is using ** online network, then you have to prepare an additional modem, commonly known as "cat").

2.Enter the corresponding account password, and after entering, you will see that you have entered the corresponding account and password, and generally the newly bought ones are admin.

3.Select the Setup Wizard, and then enter the operation interface, you will see a Setup Wizard on the left, and Attack enters (usually it pops up automatically).

4.Go to the Internet access mode settings and set the interface of the wizard.

5.Click Next, enter the Internet access method settings, we can see that there are three Internet access options, if your home is dial-up, then use PPPOE. Dynamic IP can be used by plugging the computer directly into the network, and there is a DHCP server on the upper layer.

The static IP is generally a private line or something, or it may be a cell bandwidth, etc., and the upper layer does not have a DHCP server, or wants to fix the IP. I chose PPPoE because I dialed.

6.Enter the account password, select PPPoe dial-up Internet access to fill in the Internet account and password, this should be understood by everyone, open broadband will have an account number with, fill in it OK.

7.Set the password of the router, and then enter the wireless settings after the next step, we can see the channel, mode, security options, SSID, etc., generally the SSID is a name, you can fill in as you like, and then the mode mostly uses 11BGN. For wireless security options, we need to choose WPA-PSK WPA2-PSK, which is so safe that it will not be hacked and rubbed by the network.

8.The next step is to set it up successfully.

9.Click Done, and the router will automatically restart, so be patient. The interface that appears after success.

Wireless router encryption methods.

1.Using the encryption methods such as WEP and WPA provided by the wireless router, WEP is generally simple to set up.

2.Or use restrictions to restrict the connection by the MAC address, which means entering the MAC machine in the access restriction list to connect to your wireless router.

3.A simpler way is to turn off the SSID broadcast, that is, you can't search for the SSID of your AP, and you can only manually fill in the correct SSID by yourself to connect.

I don't know why I use a switch? You can use the router directly to access the Internet. If you need to connect to a large number of computers, you need to change the start of the switch to the start of the switch, and the start of the switch in the initial state is also the same.

Go to the router, change the IP link method, change it to on-demand allocation, and see.

Is it that the IP address of your router and the IP address of the switch conflict, for example, it will definitely cause the network to be abnormal.

Why can't I use the wifi when I change a router, and even the wifi is gone?