Give me advice to a master who understands network connection, and if you can t connect to the netwo

If you use a router, the ADSL dial-up process is completed by the router, as long as the router is not turned off, it will always be connected!

There are several possibilities for the router to be connected to the boot as you said.

1.The shutdown time is not long, and the IP address lease of your machine has not yet been released, so there is no need to request the IP address.

2.It's that your machine is better, and the distance from the router is relatively close, and the process of doing ARP is faster, so you can't feel it.

This way of using a router to access the Internet is a peer-to-peer network, that is, everyone has the same permission to use the bandwidth of the network, and if someone else takes up resources first, you will naturally be slow!

You don't understand the last sentence of "what about ADSL", is it ADSL's ISP provider that does speed limiting?

A few questions typed so many words strongly ask for extra points.

1.Directly asking you to dial is ADSL's cat.

2.The router is like a small dialer, which connects to the cat and sets up automatic dialing in the router. Then you can use the router to divide multiple computers to access the Internet, and you don't need to dial up anymore. Routers have wireless routers and wired routers.

3.Most routers have a limited speed feature. If you want to limit the speed of a certain computer, first bind the MAC address of that computer to a fixed IP in the router, and then limit the speed. The MAC address is visible in the router.

The connection is adsl modem->router->client (your computer) Generally, the router is used to trigger the adsl dial-up to connect to the network. As long as you have the administrative rights of the router, you can go to the settings. ADSL in general is telecom controlled, you can't here.

Well, it's connected to the router when you open it, and the adsl is not public.

You have to go through a router to share it I don't know what you're trying to ask for help Explain it clearly.

Is there a router and there is a router to see if it is a router problem, restart the router, there is no router plug-in and dial directly, click Set up a new connection,-- select Connect to intrenet,-- next select the broadband pppoe link, and enter the broadband account password.

If you need a wireless connection, click on an icon in the lower right corner of the desktop, which is similar to the mobile phone signal, find your router name and link it, enter the method of entering the router in the browser or, the admin username and password are also guest, go in and see the running status to know what's going on There is a router to see that the router WAN port is plugged into the main line of the port The indicator light is not on, and the light is the router problem.

If the network fails, check the network cable and restart the computer.

You can dial the number to indicate that the network connection is successful, repair the browser, and then uninstall and reinstall your program.

I had a good web page a few days ago, but only a few networks could not be opened, and then the network engineer helped me solve it, it was changed by someone else, I don't know if yours is, I hope it will be useful to you.

Aquatic agate, natural state, good-looking patterns, genuine good quality in the market generally shouting about 1000; Genuine and collectible.

Mammoth tusks, it's just too dry and cracked, (too weathered). **Will be greatly discounted. You can't make too good and too valuable utensils. It is recommended to keep it as is. Treat as much as possible. Otherwise, it will get worse and worse.

Do not set IPv6 for non-education networks and administrative networks, and the basic network does not support it.

It doesn't need to be that much trouble.

If you want to remove the NIC driver, you need to delete it cleanly.

Or it's as simple as changing slots.

But you can delete it in Device Management.

After the computer restarts, you can detect the new hardware, and you can install it again, and you should XP the dial-up driver that comes with it.

This is not a problem with the reinstallation of the network card, it is a system problem. Just reinstall the system and you're good to go. Otherwise, it's the same as many connections you re-establish.

It has nothing to do with the network card, it might as well delete the dial-up connection and build a new one, maybe it will be better.

Here's a password to remember! Just click on it.

You don't need to enter the password anymore, you can just click on it next time.

Install Starry Sky Express, enter your username and password, and save.

It should be possible to try another dialing software, but if it doesn't work, reinstall the system.

First of all, put a boot disc into it, then DOS boot, and then reinstall the system again.

You put my account and password in it, and take a look at it in the cat.

Faint to death, if there is a problem with the chip of your network card, you should simply change the network card, how much is it, and the driver is also a little more convenient.

1。Try swapping slots first.

2。Change the network NIC.

Next, select Connect to the Internet, then select Manually Set My Connection, Next, choose to connect with a broadband connection that requires a username and password, enter the name, and then select Anyone can use it, and then prompt to enter the broadband account and password, check the remember password and shortcut to the desktop, double-click the desktop icon to dial.