What is the experimental method for removing a small amount of sodium silicate from silica?

The experimental method of removing a small amount of sodium silicate in silica is to dissolve it in water and then filter it and then dry it (sodium silicate is easily soluble in water, and the solubility is very large, silica can't, the chemical formula SiO2, also known as silica, is widely distributed in nature, such as quartz, quartz sand, etc.). Colorless or white crystals, light yellow when containing iron, density, lemostitus melting point 1670, cristobalite melting point 1710, boiling point are 2230, insoluble in water and acid (except hydrofluoric acid), because silica is an atomic crystal, its covalent bond is relatively strong, in general is not easy to break. It can react with molten alkali.

It is used to make glass, pottery, refractory materials, etc. Silica is a hard and insoluble solid, and natural silica is divided into two categories: crystalline and amorphous; The main component of quartz is silica crystals, and the hexagonal columnar quartz crystals that are transparent in nature are crystals; Silica is an atomic crystal, so it has a high melting point and a lot of hardness; Chemically stable, it can react with alkali anhydride, alkali and some salts, and is insoluble in water and does not react with water. And the cations of hydroxides are all metal ions!

Soluble in water to make a solution limestone with hydrochloric acid, CaCO3 precipitation, CaCO3 + 2HCl = CaCl2 + CO2 gas + H20, pass into the clarified lime water to precipitate to generate SiO2 + 2NaOH = Na2SiO3 + H2O Na2SiO3 + 2HCl = H2SiO4 precipitation + H2O + 2HCl Hydrogen fluoride will react with sodium silicate, a component of glass, and corrode glass.

Silica is insoluble in water, whereas sodium silicate is easily soluble in water. Because quartz is insoluble in hydrochloric acid, limestone is soluble in hydrochloric acid and releases carbon dioxide gas, whereas quicklime dissolved in hydrochloric acid does not release carbon dioxide. NaOH reacts with SiO2:

2 naoh + sio2 ＝ na2sio3 + h2o

Dissolved and filtered with water Silica is insoluble in water, whereas sodium silicate is easily soluble in water.

In the experiment of preparing silica by precipitation method, the role of sodium sulfate is to use the template. It can promote the more complete growth of the crystal, and also play a dispersing role, so that the fineness is as uniform as possible. If sodium sulfate is not added, the result will not react.

Insoluble in water and most acids, it will become an aggregate fine particle after absorbing moisture in the air. Soluble in caustic soda and hydrofluoric acid. It is stable to other chemicals, resistant to high temperatures, does not decompose, and does not burn.

It has high electrical insulation, porosity, large inner surface area, water absorption, and non-toxic.

The function of sodium sulfate in the preparation of silica is to be used as a template, which can promote the more complete growth of the crystal, and also play a dispersing role, so that the fineness is as uniform as possible.

Summary. The method of sodium silicate for the analysis of sodium oxide and silica is achieved by titration. This method decomposes the sodium silicate in the sample and reacts with the sodium hydroxide in the solution in sodium hydroxide hydrochloric acid solution to form sodium oxide and silica.

As the titrant and standard solution are continuously instilled, the pH of the reaction system is changed. When the reaction components are completely reacted, the content of the reaction components is calculated by detecting the end point of the reaction system. This titration method can be widely used in laboratory and industrial production, and is one of the important methods for sodium silicate analysis.

The method of sodium silicate for the analysis of sodium oxide and silica is achieved by titration. In this method, the sodium silicate in the sample is decomposed and reacted with the wide digging sodium hydroxide in the sodium hydroxide hydrochloric acid solution to form sodium oxide and silica. As the titrant and standard solution are continuously instilled, the pH of the system containing nucleation reactions will be carefully adjusted.

When the reaction components are completely reacted, the content of the reaction components is calculated by detecting the end point of the reaction system. This titration method can be widely used in laboratory and industrial production, and is one of the important methods for sodium silicate analysis.

Fellow, I really didn't understand, I can be more specific.

The method of sodium silicate for the analysis of sodium oxide and silica is achieved by titration. In this method, the sodium silicate in the sample is decomposed and reacted with the wide digging sodium hydroxide in the sodium hydroxide hydrochloric acid solution to form sodium oxide and silica. As the titrant and standard solution are continuously instilled, the pH of the system containing nucleation reactions will be carefully adjusted.

When the reaction components are completely reacted, the content of the reaction components is calculated by detecting the end point of the reaction system. This titration method can be widely used in laboratory and industrial production, and is one of the important methods for sodium silicate analysis.

Yes, the acidity of silicic acid is less than that of carbonate code, and silicic acid spring plum can be prepared.

The slow slip phenomenon of continuous introduction of CO2 into sodium silicate is the formation of white silicic acid precipitate.

CO2 + H2O + Na2SiO3 = H2SiO3 + Na2CO3 (when CO2 is small).

Na2SiO3 + 2CO2 + 2H2O = 2NaHCO3 + H2SiO3 (when CO2 is in excess).

Yes, silicic acid is less acidic than carbonic acid, and silicic acid can be prepared.

The phenomenon of continuous introduction of CO2 into sodium silicate is the formation of white silicic acid precipitate.

CO2 + H2O + Na2SiO3 = H2SiO3 + Na2CO3 (when CO2 is small).

Na2SiO3 + 2CO2 + 2H2O = 2NaHCO3 + H2SiO3 (when CO2 is in excess).

Yes, but no matter how much CO2 passes, it produces sodium bicarbonate, because carbonic acid is stronger than silicic acid and stronger than bicarbonate.

Summary. The temperature ranges from 784-853 degrees Celsius, with a peak of 835 degrees Celsius.

Ask the professionals: At what temperature should sodium carbonate react with silica to form sodium silicate?

The temperature ranges from 784-853 degrees Celsius, with a peak of 835 degrees Celsius.

Na2CO3 + SiO2 = Na2SiO3 + CO2 According to the previous measurements of the suffocation resistance, the reaction occurred at a temperature of 784-853 degrees Celsius, with the highest peak at 835 degrees Celsius in Jingheng.

The reason for this reaction is that the carbon dioxide gas produced volatilizes so that the reaction can be carried out in the forward and complete direction. It should be noted that the reaction occurs at high temperature, and the reaction law at room temperature cannot be applied at this time. At high temperatures, sodium carbonate can be decomposed into sodium oxide and carbon dioxide deficiency.

The carbon dioxide leaves the system as a gas, and the silica left behind is combined with the sodium oxide to form sodium silicate. It is in line with the metathesis idea of gas production.

Kiss, if you can, you can give Xiao Tao a thumbs up Thanks, I wish you a happy life, goodbye

Summary. The reaction of 100 grams of sodium silicate and sulfuric acid can produce about one gram of silica.

The reaction of 100 grams of sodium silicate and sulfuric acid can produce about one gram of silica.

To solve this problem, we need to know the chemical equation formed by the reaction of sodium silicate and sulfuric acid, and then use stoichiometry to calculate the number of moles of silica produced. The chemical equation is: Na2SiO3 + H2SO4 SiO2 + Na2SO4 + H2O, as can be seen from the square shade program, for every 1 mole of sodium silicate, the reaction produces 1 mole of silicon dioxano hailstone.

Now you want to convert 100 grams of sodium silicate to the number of mohongminer. To do this, we need to know the molar mass of sodium silicate. The molar mass of sodium silicate is g mol, so 100 grams of sodium silicate is equal to molar sodium silicate (100

Because 1 mole of sodium silicate produces 1 mole of silica, molar sodium silicate will produce molar silica. Finally, we need to convert the resulting silica into grams. The molar mass of silica is g mol, so molar silica is equal to g silica (

Thus, 100 grams of sodium silicate and sulfuric acid can react to produce about one gram of silicon dioxide.

Please note that this is only an approximation and actual yields may be affected by reaction conditions and purity.