How to adjust the area accuracy in VIVSO

Looking forward to the tormenting pain of the onset of drug addiction. It's as if a person who has been imprisoned in a dark room for a long time suddenly hears the sound of approaching footsteps that have not been seen for a long time. As a result, the door of the heart that had been locked all this time also cracked open a small crack that was not easy to be noticed, and he waited for the further tentative knock of outsiders during the breathing period.

But the fingers outside the door hesitated, and the heart inside the door was anxious. A tangible bond was formed silently like this!

Love is the product of the emotional collision between the sexes, it is born of loneliness, but in the periodic shaking of the bond of love, it is the feeling. Perfect.

1. All files - configuration - CASS parameter configuration - measurement parameters - advanced settings - earthwork number of decimal places; the number of decimal places in the grid elevation; The number of decimal places for area statistics.

File --cass parameter configuration --- number of elevation annotation digits.

This can't be set.,The version is two digits.,The version is 3 decimal places.。

Legally, there is no need to measure the area, because according to the plan, the homestead must be arranged horizontally and vertically, which cannot affect the visual effect.

1. First open Sketch Master.

2. Draw a flat figure and a three-dimensional figure.

3. Select one of the graphics and click the zoom button to adjust the size of the graphics.

4. You can also enter the scale in the number field to accurately adjust the size of the model.

5. Click the rectangle tool in the toolbar to draw a rectangle in the workspace, and you can enter a value in the lower right corner to specify its size.

6. Click the push and pull tool in the toolbar, and enter a value in the lower right corner to specify its height.

7. Click the angle tool in the toolbar and enter the value in the lower right corner to draw the angle accurately.

8. When drawing, operations such as zooming and splitting can also be accurately adjusted through numerical values.

According to what you said, it should be possible, no need to do any settings Select the rectangle, draw a point with a brush, and then drag a rectangle into the input in the lower right corner Enter 1000, 500 Enter Enter enter and it should be fine.

The input method of comma does not seem to work if it is Chinese.

Start by clicking on the rectangle.

Determine the endpoint. Input data:

Data A comma (,) Data b

Confirm the carriage return.

Left-click and type e.g. 100, keyOr pull out a rectangle and enter a numeric value.

When you enter a value, you must have a comma in the middle, and it is an English input method to be effective.

Don't use Chinese commas, use English.

According to the European standard EN779, the filter paper has medium efficiency, high efficiency and super high efficiency. The medium effect is divided into F5, F6, F7, F8, and F9; Efficient is divided into H10, H11, H12, H13, H14, H15, H16; Ultra-efficient is rarely used.

1. Open the relevant window of Tianzheng building directly, and you will find that the measurement accuracy is an integer.

2. Next, if there is no problem, continue to select the format in the menu bar and click on the unit.

3. At this time, a new interface will pop up, and you need to determine it accurate to three decimal places according to the diagram.

4. In this way, after getting the corresponding results, the goal can be achieved.

In the menu bar format, select the unit, which contains the length unit precision and the angle unit accuracy, both of which can be adjusted. I usually set 3 decimal places.

I haven't used the Tensho Building, but generally you can adjust the accuracy to in the settings.

Enter the command un space, and change the precision to three decimal places in it.

Press the d space (change the number of digits to save it).

I'm better off digging than you're going to find it! Ha ha! Steps: Format - Units, change the precision to the number of decimal places you want, ok....Then AA, choose your graphics to change lead.

CAD defaults to millimeter units. Single-digit millimeters. Architectural decoration on the millimeter as a unit, one-to-one scale drawing, so there is no need to set any unit, precision.

Type d, then click Modify and select "Main Unit" in the header above. The second precision is to adjust the back to the units you want, which can be an integer or a decimal. Look at the unit you want.,Then click "OK.,Set it to current.,OK。。。

Tools-Format-Units. There are two options, length and angle, and you can choose the exact number of decimal places you want in the unit of measurement.

Here's how to set it up:

1.Set shortcut definitions, including, modifying, and annotating.

2.Set the right mouse button to repeat the previous command and perform the action.

3.Use standard A4 wireframe, or specify your own A4 wireframe, standard part drawing frame, and save.

4.Define the size, width, and color of each line in the layer. After taking the name, save it.

5.In the options, tick Don't create backup files.

6.In the options, drag the crosshairs to the far right and select the set without pressing shift.

7.Smoothness adjusted to a maximum of 20,000.

8.Define the default Chinese font and define the default callout font.

9.Define the annotation format as well as the text formatting.

10.Select a save path.

Then it's time to draw.